CenturionPro Original Manual de usuario
For more information or to watch our video tutorials visit cprosolutions.com 1
OWNERS MANUAL
The Original & Silver Bullet
cprosolutions.com
1 855 535 0558
cprosolutions. 1 855 535 0558
2
OWNERS MANUAL
The Original & Silver Bullet
For more information or to watch our video tutorials visit cprosolutions.com 3
TABLE OF CONTENTS
Important Safety Information 4
Machine Assembly 5
Cover Assembly 6
Triple-Bag Kief Collection System 7
Leaf Collector Assembly 8
Hopper Assembly 9
Blade Removal 10
Cleaning the Original & Silver Bullet 10
Leaf Collector Cleaning 11
Machine Maintenance 12
Quantanium Coated Non-Stick Tumbler 13
Warranty Information 14
Frequently Asked Questions 15
Additional Assistance 16
Original & Silver Bullet Machine and 17
Leaf Collector Specifications
Trimming Dry? Here Are Some Important Tips 18
Trim Both Wet and Dry 19
Troubleshooting 20-21
cprosolutions. 1 855 535 0558
4
IMPORTANT SAFETY INFORMATION
This document refers to the CenturionPro Solutions Original & Silver Bullet
automated trimming systems.
The Original & Silver Bullet are high-speed trimming systems, requiring that
specific safety precautions are practiced during operation to reduce the risk of
personal injury. Improper use of The Original, Silver Bullet, or any Centurion Pro
trimming machine, may cause serious or fatal injury. Please ensure you read the
operations manual and warning notes before using the Original or Silver Bullet.
Do not lend out or rent your Original or Silver Bullet without this operating
manual. A first time user should obtain proper instruction prior to use.
GENERAL
• Do not move, disassemble, clean or inspect the trimmer while the power is still connected to the machine.
• Replacement parts are specific to The Original & Silver Bullet and must be purchased from an authorized
dealer only. Substituting factory parts with non-approved third-party replacements may result in damage to
the machine or bodily harm.
• Keep all individuals a safe distance from the work area. Do not operate the machine around children.
• Do not remove safety labels. Replace any and all labels if they become damaged or obscured.
CONNECTION
• As with home appliances, The Original & Silver Bullet must be used in connection with a properly grounded
receptacle.
• Never plug in or power up your trimming machine if the protective shrouds are removed.
• Do not use extension cords over 8m (25ft) in length to power the Original or Silver Bullet.
OPERATION
• The initial set up will show assembly instructions to unpack and set-up your machine.
• Your bed bar blade has been factory set to cut perfectly. Please do not adjust your blade until it is time to
clean the machine. Also, please watch the video tutorial located on our website on how to adjust your blade
before attempting.
• Safety glasses should be worn at all times while operating The Original or Silver Bullet.
• Do not operate any trimming machine while tired or under the influence of medication, drugs or alcohol.
• Do not put anything other than plant material into the tumbler. Doing so may cause damage to the tumbler,
the machine or result in bodily harm.
• Operate the trimmer in a well ventilated area in order to prevent overheating.
MAINTENANCE
• Never leave The Original or Silver Bullet system running unattended.
• Never conduct maintenance or cleaning while the machine is plugged in.
• Do not modify or adapt any part of the trimmer or its accessories. Doing so may cause irreversible damage
to the machine or result in bodily harm.
IMPORTANT
For more information or to watch our video tutorials visit cprosolutions.com 5
MACHINE ASSEMBLY
TOOLS REQUIRED
1 x #2 Phillips Screwdriver
1 x 3/32" T-Handle Allen Wrench
1 x 5/32" T-Handle Allen Wrench
1 x 1/8" T-Handle Allen Wrench
1 x 3/16" T-Handle Allen Wrench
1 x 3/8" Wrench
Tighten Four Sealing
Bolts & Washers
Note the longer end of the
TUMBLER when re-installing
Cover
Brush
Upper Frame
Tumbler
Blade
Adjusters
Requires Cleaning
See Page 10
Tumbler O-Ring
Cutting Reel
Lower Frame Shroud
(area behind cutting reel)
Requires Cleaning
See Page10
Requires Cleaning
See Page 10
Requires Cleaning
See Page 10
Bed Bar Blade &
Magnet Bar
STEP 1
PLACE
TUMBLER IN
GROOVES
STEP 3
INSTALL
COVER
STEP 2
INSTALL
UPPER
FRAME
STEP 4
INSTALL
SKIRT
(INSTALLED ON THE
MACHINE WHEN
SHIPPED)
110V
220V
North
America
Australia
EU
Motor
cprosolutions. 1 855 535 0558
6
COVER ASSEMBLY
It is UNSAFE to operate the ORIGINAL or SILVER BULLET TRIMMER without COVERS!
STEP 1
Attach the BEARING COVER to the ORIGINAL
or SILVER BULLET
STEP 2
Attach the BELT COVER to the ORIGINAL
or SILVER BULLET
Belt Cover
4x Washers
4x Bolts
Belt Cover
Bearing Cover
2 x Washers
2 x Bolts
Bearing Cover
For more information or to watch our video tutorials visit cprosolutions.com 7
TRIPLE-BAG KIEF COLLECTION SYSTEM
Kief is becoming wildly popular due to the rise of extractions. Unfortunately, machines that require
sprays can contaminate and destroy your Kief, therefore making it virtually useless.
Thankfully, CenturionPro offers an optional non-stick Quantanium coating on the tumblers. This means
no spray is needed so your Kief remains 100% pure and usable. To further benefit growers, we devel-
oped a new triple-bag filtration system. This system will assist with Kief collection, separating it from
your trim. This allows you to safely and easily collect the precious trichomes for further processing and
profits.
With your machine, you will see that you have a black mesh bag, a white nylon bag, and an outer cloth
bag. The black bag goes inside the white nylon bag, which then goes inside the white cloth bag.
The bags are easy to wash with a pressure washer using cold water. The bags can also be put through
the washing machine, but it is recommended to be run through on a cold delicate cycle only.
The green leafy trim will collect in the new
inner black bag.
Only the Kief makes it through the black bag
and collects in the outer mesh bag.
Outer cloth bag catches any Kief that may
pass through the micron white bag.
Turn off the machine and remove the inner
bag and then extract Kief. ENJOY!
HOW IT WORKS
cprosolutions. 1 855 535 0558
8
LEAF COLLECTOR ASSEMBLY
4” Flex Hose
Secure with one 4”
hose clamp
Zipper
Leaf Collector Bag System Leaf Collector
Secure with
4” hose clamps
Requires Cleaning
See Page 11
Requires Cleaning
See Page 11
Secure with 4”
Hose Clamps
110V
220V
North
America
Australia
EU
STEP 1
ATTACH BAG
SYSTEM TO LEAF
COLLECTOR
STEP 2
ATTACH 4" FLEX
HOSE TO THE
DIVERTER AND
ORIGINAL OR
SILVER BULLET
Please disregard hole on
top of diverter, the suction
will hold the diverter in
place and no screw is
needed to secure.
For more information or to watch our video tutorials visit cprosolutions.com 9
HOPPER ASSEMBLY
STEP 1
ASSEMBLE
THE FRAME
STEP 2
SECURE THE
HOPPER BAG TO
THE FRAME
STEP 3
CONNECT THE
HOPPER TO THE
MACHINE
Inward
Hopper
Bag
Opening Frame (Back)
Frame (Front)
Ensure the
OPENING and
FRAME (front) match
Ensure the RODS are
facing inward. Secure with
1/4" BOLTS, WASHERS
& LOCKING NUTS
Ensure the Frame and OPENING
match the ORIGINAL & SILVER BULLET
machine exactly
cprosolutions. 1 855 535 0558
10
WARNING:
Avoid direct water
contact on motor
Clean with pressure-washer at 1500-2000 PSI.
Hot water, fan spray setting.
Run the machine for 15 minutes
aer washing. Allowing components to dry.
Clean the length of the Cutting Reel and
Shroud of all debris.
For optimal performance and life, the components must be cleaned every 2 to 3 days of use.
For optimal performance and life, the BLADES and the MAGNET BARS must be removed and cleaned every few hours of operation.
IMPORTANT NOTE: Your bed bar blade has been factory set to cut perfectly. Please do not alter the settings of your machine.
You might notice slight contact between your rotating cutting reel and the flat bed bar blade - this is normal.
Remove BLADE
then MAGNET BAR
carefully!
Clean BLADE and MAGNET
BAR with a utility knife.
Wipe clean with acetone.
BLADE
BLADE REMOVAL
CLEANING THE ORIGINAL & SILVER BULLET
For optimal performance and life, the components must be cleaned every 3 to 4 days of use.
Clean the Brush using
pressure washer
Clean the length of the
CUTTING REEL and
SHROUD of
all debris
Avoid
water
on the
Clean with pressure-washer at 1500-2000 PSI.
Hot water, fan spray setting.
Run the Original or Silver Bullet for 15 minutes
after washing. Allowing components to dry.
Otros manuales para Original
1
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Recortadora de CenturionPro
CenturionPro
CenturionPro XL Series Manual de usuario
CenturionPro
CenturionPro GC1 Manual de usuario
CenturionPro
CenturionPro THE MINI Manual de usuario
CenturionPro
CenturionPro DBT 4 Manual de usuario
CenturionPro
CenturionPro Original Manual de usuario
CenturionPro
CenturionPro The Gladiator Manual de usuario
CenturionPro
CenturionPro 3.0 Manual de usuario
