Celsi B-1004554 Manual de usuario

22” & 33” Ultiflame Electric Fire

Model No’s:

B-1004554, B-1004555

CEUL22RE-ERP, CEUL33RE-ERP

Packing Checklist

Electric Fire



Remote Control Handset*



Log Set



Ember Ice Set



Instruction Manual

*THIS PRODUCT REQUIRES 2 X AAA BATTERIES FOR USE IN THE HANDSET (NOT SUPPLIED)

IMPORTANT

PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE

INSTALLATION AND USE OF THIS ELECTRIC FIRE AND RETAIN

FOR FUTURE REFERENCE.

This appliance is not intended for use by persons (including children) with

reduced physical, sensory or learning disabilities, or lack of experience

and knowledge, unless given supervision or instruction concerning use of

the appliance by a person responsible for their safety.

Page 1

IMPORTANT SAFETY ADVICE

WHEN USING AN ELECTRICAL APPLIANCE, BASIC PRECAUTIONS SHOULD ALWAYS

BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK AND INJURY TO

PERSONS, INCLUDING THE FOLLOWING IMPORTANT SAFETY ADVICE.

DO NOT cover or obstruct the airflow to the front of the heater. This is to avoid over-heating

of the product.

DO NOT leave the heater unattended while it is in use. Always turn the appliance to the OFF

position and switch off at the mains socket when not in use.

DO NOT leave children unsupervised whilst the appliance is switched on.

DO NOT operate this appliance with a damaged cord or plug, or after the appliance

malfunctions, has been dropped or damaged in any way.

DO NOT install a timer switch to operate the appliance.

DO NOT use this appliance as a freestanding appliance. It must always be securely fixed into

a Chimney breast opening.

DO NOT insert or allow objects to enter any ventilation or exhaust openings on the appliance.

To prevent a possible fire do not block air intakes or exhaust openings in any manner.

DO NOT place this appliance near flammable materials, surfaces or substances, as there may

be a risk of fire. Keep flammable materials, surfaces or substances at least 1 metre away from

the front of the product.

DO NOT switch on the fire if volatile vapours are present in the room.

DO NOT use this appliance in any areas where petrol, paint or other flammable liquids are stored

e.g. a garage or a workshop as the appliance contains components capable of producing a spark.

DO NOT let bare skin touch any hot surfaces to avoid burns and personal injury. The heater vent

will get hot when in use.

DO NOT use outdoors.

CAUTION- Some parts of this product can become hot and cause burns. Particular attention has

to be given where children and vulnerable people are present.

This appliance is for household use only

Page 2

Product Technical Data Sheet

Supplier Name / Trademark CELSI

Supplier Model Identifier B-1004554, B-1004555 ULTIFLAME 22” & 33”

Voltage 230v AC 50HZ

Fuse 13 Amp

Nominal Heat Output (Measured) 1.6 kW

Minimum Heat Output (Indicative) 0.8 kW

Maximum Continuous Heat Output 1.6 kW

Auxiliary Electricity Consumption at Nominal Heat Output

0.016 kW

Auxiliary Electricity Consumption at Minimum Heat Output

0.016 kW

Auxiliary Electricity Consumption at Standby Mode

0.0005 kW

Type of heat Output / Room Temperature Control With electronic room temperature

control plus week timer

Other Control Options

With adaptive start control

Manufacturers Name and Address

BFM Europe Ltd. Gordon Banks Drive,

Trentham Lakes, Stoke-on-Trent, Staffs, ST4

4TJ Tel: 01782 339000

Ultiflame 22”

Ultiflame 33”

Page 3

Unpacking

Remove and discard the plastic bag.

Be responsible when handling the packing materials.

Keep the original packaging for future transportation and/or storage.

Check all accessories are removed from the packaging before storing it away for future use.

KEEP PLASTIC BAGS AWAY FROM CHILDREN!

Choosing a suitable location

This electric fire is designed to be fitted within an existing brick / masonry chimney breast which

must be dry with the chimney capped off using a suitable chimney cap.

The appliance must be kept away from any source of damp or moist conditions. Avoid any close

contact with water.

Important Notice: To reduce heat losses and to prevent any chimney up draught

affecting the operation of your fire we recommend that the chimney is blocked off.

The chimney breast, wall or fireplace must be of sound construction and all fixings used must

be suitable for the type of wall. If there is any doubt regarding the suitability of the installation

site please contact your supplier.

From the front of the fire ensure that there is a minimum clearance of 50mm between any

non-combustible materials. For combustible material clearances please consult with the

manufacturer.

The fire can be connected direct or plugged into a mains socket which can be sited on the

right hand side of the fire.

Ensure that the plug socket-outlet connection for this appliance is accessible. It MUST be readily

accessible for easy electrical isolation in the event of servicing and replacing components etc.

This appliance MUST NOT be located immediately below an electrical socket-outlet.

Page 4

Installation

Please refer to the relevant installation instructions applicable to the model fire

purchased. Installation must be carried out by a qualified and competent person.

The opening sizes required to install the fires are

Ultiflame 22”

H : 650mm

W : 610mm

D : 185mm

Ultiflame 33”

H : 605mm

W : 890mm

D : 185mm

Connect the appliance to single-phase AC supply of the voltage specified on the rating plate.

Should the fire be connected directly into the mains supply, then a fused switched spur with a

13 amp fuse must be fitted. It is imperative that the power supply is capable of handling a load

of 2000 watts (2kw). This appliance must be earthed. Allow sufficient flex to enable the fire to

be removed from the wall. Do not use an extension lead

IMPORTANT NOTE: Models which have LED downlights included in the suite / surround will

require an additional mains supply. If wired directly into the mains supply, then a fused

switched spur with a 3 amp fuse must be fitted ensuring that the plug socket-outlet connection

is accessible. It MUST be readily accessible for easy electrical isolation in the event of servicing

and replacing components etc.

Always ensure that all electrical work complies with the relevant Building Regulations

and the Electrical Code of Practice. All electrical work should be carried out by a

qualified electrician.

Page 5

Ultiflame 22” & 33” Wall Mounting

The base of the fire opening must be solid, level and firmly fixed to safely support the weight

of the fire.

The fire is held in place using

4 suitable screws and

fasteners in the 4 fixing holes

on the sides of the appliance.

4 x Fixing Holes

A false studded chimney breast can be built with a plastered finish to encase the fire

The chimney wall can now be finished with plasterboard or an alternative facing material which

terminates at the facing trim.

The fire can be fitted direct into the chimney breast and plastered flush up to the facing trim

Ultiflame 22” & 33” with Trim option

Installation is the same principle as wall mounting but the fire is screwed to the plastered wall to

ensure that the facing trims protrude from the fire. For fitting of the trim please refer to the

instructions included with the trim.

Page 6

Rennes, Avignon & Lille Models (22”)

Fireplace opening for Pablo, Boticelli & Angelo Surrounds

When fitting this fire into a surround the fireplace opening needs to be prepared at

differing heights dependent upon which surround type is to be installed.

Pablo Surround

Fire opening to be

146mm from floor level

Boticelli Surround

Fire opening to be

146mm from floor level

Angelo Surround

Fire opening to be

172mm from floor level

Page 7

INSTALLING THE “PABLO” SURROUND

1. Unpack the surround from the wooden crate, check all parts are present and carefully store

the components.

Contents of Pablo surround:-

1 off hearth panel

1 off R/H leg

1 off L/H leg

1 off R/H infill section

1 off L/H infill section

1 off bottom infill section

1 off shelf

1 off stub hearth

2. The underside of the hearth should be painted with a weak PVA (8 parts water to 1 part

PVA). This will prevent staining penetrating through the stone. The hearth must be

centred to the opening. If the fireplace is to be installed on a chimney breast ensure that

the opening is also centred to the chimney breast. It is essential that the hearth is

completely level. The hearth must be bedded down on bonding or an equivalent material.

Avoid cement based products and ensure the hearth is firmly fitted and well supported.

Allow the bedding material to set before any weight is placed onto the hearth. Wipe off

any surplus bonding material with a wet sponge.

3. Fit bottom section to hearth, ensure it is central before fixing with a suitable

mastic adhesive.

4. Fit brackets to top of legs, offer leg up to wall and mark position of fixing hole on wall, use

shelf to ensure legs are correctly spaced / positioned. Remove shelf then cover hearth with

dust sheet and drill the fixing holes. Remove the brackets from the legs, fix the side infills

into place with suitable adhesive and secure the leg fixing brackets only to the wall. Fit legs

to brackets that have been securely attached to the wall with fixings as detailed in Point 5.

5. Assess the chimney breast onto which the fire is to be installed and ensure that

it is of sound construction and suitable for supporting the weight of the

surround. Fixings used to secure the leg brackets to the masonry of the

chimney breast shall be of expansive stainless steel or galvanised steel type

masonry fixings for dense concrete blockwork or brickwork. Where fixings are

located into light weight blockwork or friable aggregate blocks, the fixings shall

be of the resin anchor type.

Page 8

6. Fix the top infill and shelf infill into place again with suitable mastic adhesive.

7. Fit shelf into place ensuring it is correctly aligned with legs, mark the position of holes for

securing brackets on wall, remove shelf and drill wall and insert fixings in accordance with

Point 5, these brackets can be recessed if required. Fit the stub hearth in position between

the legs.

8. Ensure that the surround components as shown below are mechanically secured as

indicated, this is required in accordance with the latest revision of

BS 1251 : 2015

Open Fireplace Components.

9. Once the fireplace is correctly installed, grout all of the joints including between the

fireplace and the wall with a water based cream mastic or tile grout. Ensure all surplus

grout is immediately removed by washing the stonework using a sponge and clean water.

Page 9

INSTALLING THE “BOTICELLI” SURROUND

1. Unpack the surround from the wooden crate, check all parts are present as per below and

carefully store the components.

Contents of Boticelli surround:-

1 off hearth panel

1 off R/H leg

1 off L/H leg

1 off R/H infill section

1 off L/H infill section

1 off bottom infill section

1 off shelf top infill section

1 off shelf top section

1 off top infill section

1 off stub hearth

2. The underside of the hearth should be painted with a weak PVA (8 parts water to 1 part

PVA). This will prevent staining penetrating through the stone. The hearth must be

centred to the opening. If the fireplace is to be installed on a chimney breast ensure that

the opening is also centred to the chimney breast. It is essential that the hearth is

completely level. The hearth must be bedded down on bonding or an equivalent material.

Avoid cement based products and ensure the hearth is firmly fitted and well supported.

Allow the bedding material to set before any weight is placed onto the hearth. Wipe off

any surplus bonding material with a wet sponge.

3. Fit bottom section to hearth, ensure it is central before fixing with a suitable

mastic adhesive.

4. Fit brackets to top of legs, offer leg up to wall and mark position of fixing hole on wall, use

shelf to ensure legs are correctly spaced / positioned. Remove shelf then cover hearth with

dust sheet and drill the fixing holes. Remove the brackets from the legs, fix the side infills

into place with suitable adhesive and secure the leg fixing brackets only to the wall. Fit legs

to brackets that have been securely attached to the wall with fixings as detailed in Point 5.

5. Assess the chimney breast onto which the fire is to be installed and ensure that it is

of sound construction and suitable for supporting the weight of the surround.

Fixings used to secure the leg brackets to the masonry of the chimney breast shall

be of expansive stainless steel or galvanised steel type masonry fixings for dense

concrete blockwork or brickwork. Where fixings are located

Page 10

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Chimenea de interior de Celsi

Celsi

Celsi Electriflame VR B-1005973 Manual de usuario

Celsi

Celsi B-160940 Manual de usuario

Celsi

Celsi B-1036319 Manual de usuario

Celsi

Celsi ULTIFLAME B-1004553 Manual de usuario

Celsi

Celsi B-1005975 Manual de usuario

Celsi

Celsi ELECTRIFLAME XD Mk2 B-1005344 Manual de usuario

Celsi

Celsi Electriflame VR EFVR40RE Manual de usuario

Celsi

Celsi ELECTRIFLAME XD 850HOW Manual de usuario

Celsi

Celsi 16" Electriflame XD series Manual de usuario

Celsi

Celsi B-1036317 Manual de usuario

Celsi

Celsi CFECE0RE-ERP Manual de usuario

Celsi

Celsi Electriflame Manual de usuario

Celsi

Celsi B-1005344 Manual de usuario

Celsi

Celsi Ultiflame Aleesia Manual de usuario

Celsi

Celsi B-1001645 Manual de usuario

Celsi

Celsi Electriflame VR Commodus S Manual de usuario

Celsi

Celsi Accent Infusion Manual de usuario

Celsi

Celsi Electriflame VR 750 Manual de usuario

Manuales populares de Chimenea de interior de otras marcas

Brigantia

Brigantia 35-DVRS31N-2 Manual del propietario

Nordpeis

Nordpeis Bergen Manual de usuario

Superior

Superior BCT2536TMN Manual de usuario

Quadra-Fire

Quadra-Fire 5100I-GD-B Manual de usuario

Renaissance

Renaissance RUMFORD 1000 Manual de usuario

Lacunza

Lacunza IV-800 Manual de usuario

Baxi

Baxi 940 Instrucciones de uso

Dru

Dru Maestro 60/2 Tall RCH Manual de usuario

Diamond Fireglass

Diamond Fireglass SS-O22 Manual de usuario

HearthStone

HearthStone Windsor Bay 8830 Manual de programación

Napoleon

Napoleon ASCENT B42 Manual de usuario

Enviro

Enviro E33GI Manual de usuario

Smeg

Smeg L30 FABE Instrucciones de montaje

KEDDY

KEDDY K700 Manual de usuario

Godin

Godin 3451 Manual de usuario

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manual de usuario

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manual de usuario

Desa

Desa CCFPDFT Manual de operación