Celluon Picopro Manual de usuario
User Manual
Table of Contents
1. Safety Precautions
FCC Compliance Information
FCC Class Notice
FCC Caution
FCC RF Radiation Exposure Statement
Industry Canada Statement
CE Caution
IEC-60825-1 Caution
2. Certifications
3. Environmentally Friendly Disposal and Recycling
4. Package Contents
5. Product Features
6. Identifying Parts
7. Connecting PicoPro
a. Compatible Operating Systems
b. Wired Connection
c. Wireless Connection
d. Switching Connection Mode
e. Reset Switch
8. Making Adjustments
a. Volume Adjustment
b. Speaker / Earphone Usage
c. Laser Alignment
d. APC Setting
e. Engine High Temperature Protection Mode
9. Charging the PicoPro
10. Troubleshooting
11. Specifications
12. Warranty
3
1. Safety Precautions
This product is not waterproof – avoid using it near water or wet places.
There is a risk of malfunction if product is used in places where sudden or extreme temperature changes occur.
Applying excessive force or impact to this product may result in product damage, and will void warranty.
Never attempt to disassemble or service this product yourself. Doing so can result in electrical shock and void warranty.
This is a Class 3R Laser product. For your safety, do not stare directly into the laser source. Doing so could damage your eyes.
FCC Compliance Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference to another device.
2. This device must accept any interference received, including interference that may cause undesired operation.
FCC Class Notice
This equipment has been tested and found to comply within the limits for a Class B digital device, pursuant to Part15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment.
This equipment generates, uses, and radiates radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference will not occur with special installation.
If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct
the interference by one of the following measures:
■Reorient or relocate the receiving antenna.
■Increase separation between the equipment and receiver.
■Connect the equipment to an outlet on a circuit different from which the receiver is connected.
■Consult the dealer or an experienced radio/TV technician.
FCC Caution
Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority
to operate the equipment.
4
FCC RF Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 centimeters between the radiator
and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Industry Canada Statement
This device complies with Industry Canada license- exempt RSS standard(s). Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.
CE Caution
Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
IEC-60825-1 Caution
Use of control or adjustments or performances of procedures other than those specified here in may result in hazardous radiation exposure.
5
2. Certifications
KC : MSIP-CMM-CLK-PICOPRO FCC ID : TCLPICOPRO CE1177
compliant
RoHS IC No : 10211A-PICOPRO IEC-60825-1 : Class 3R LaserIEC-60825-1 : Class 3R Laser
LASER APRETURE
LASER RADIATION
AVOID DIRECT EYE EXPOSURE
CLASS 3R LASER PRODUCT
Output: Red(90mW)/Blue(85mW)/Green(50mW)
λ= Red(639nm)/Blue(445nm)/Green(522nm)
Pulse frequency : 60Hz
IEC 60825-1:2007
3. Environmentally Friendly Disposal and Recycling
To protect the environment, dispose this product separately from household waste once it has
reached its end of life, or take it to your local electronic waste disposal center.
Built-in Battery
Use supplied USB power adapter to begin charging the battery.
Battery status is indicated by four blue LED indicators while charging.
(4 LED : 100% / 3 LED : 75% / 2 LED : 50% / 1 LED : 25%)
3140 mAh @ 3.7VBattery Capacity
Approx. 120 minutes (with continuous use)Battery Operating Time
Rechargeable Lithium-ion Polymer BatteryBattery Type
Approx. 270 minutesBattery Charging Time
Charging the Battery
6
4. Package Contents
5. Product Features
PicoPro is a laser-based HD pico projector that always stay focused and easily fits in your pocket.
It enables you to share contents from your mobile device onto any surface via HDMI connection or Miracast (Screen Mirroring) capability.
PicoPro User Manual Power Adapter Holding Mount PouchMHL Cable
7
6. Identifying Parts
Reset Button
LASER APRETURE
LASER RADIATION
AVOID DIRECT EYE EXPOSURE
CLASS 3R LASER PRODUCT
Output: Red(90mW)/Blue(85mW)/Green(50mW)
λ= Red(639nm)/Blue(445nm)/Green(522nm)
Pulse frequency : 60Hz
IEC 60825-1:2007
Laser radiates from this aperture
FCC ID : TCLPICOPRO CE1177 KC : MSIP-CMM-CLK-PICOPRO
IC : 10211A-PICOPRO
Model : PicoPro DC : 5V 2A Celluon, Inc. Made in Korea
Touch-sensitive Volume Up
Touch-sensitive Volume Down
Backlit Battery Indicator Light Speaker
MHL/HDMI cable input
3.5mm Audio Out
Battery Status Indicator
CHARGE – Micro USB port for charging
Power Button
Mode Switch Button
8
7. Connecting PicoPro
a. Compatible Operating Systems
Miracast
For HDMI Connection
Any digital device that supports HDMI capability
DLNA
For Wireless Connection
Android OS 4.2 or later
Windows OS 8.1 or higher
Any OS that supports Screen Mirroring functionality
Any digital device that supports DLNA protocol
* Using DLNA connection requires downloading DLNA
streaming app from the App Store or Play Store.
b. Wired Connection
**For proper operation of PicoPro, please do not insert HDMI cable during Miracast connection.
Using HDMI Connection :
Use plug-n-play connection for any digital/mobile device via HDMI connection.
1. Turn on PicoPro by pressing the power button for about 2-3 seconds.
1
2. Celluon logo will display upon powering on, followed by a “Preparing
wireless connection… To go to HDMI mode, press Mode Switch button” screen.
2
9
3. Press and hold “Mode Switch” button located next to power button
for 2~3 seconds to change to HDMI mode.
5. Locate MHL/HDMI port on the PicoPro and use supplied HDMI cable to connect to a device.
6. PicoPro will start mirroring contents from connected device.
4. PicoPro is now in HDMI mode.
3
*For Apple devices, please use additional Apple Digital AV Adapter to connect via HDMI cable.
*For Samsung devices, please use supplied Samsung adapter (5pin to 11pin converter) to connect to MHL/HDMI cable.
*During the use of PicoPro via supplied MHL cable, connected mobile device may charge from PicoPro's internal battery.
It is recommended to supply power via USB port on supplied MHL cable to maintain PicoPro's operating time.
4
5
10
Tabla de contenidos
Otros manuales de Proyector de Celluon
