Cassia Personal Safety Sensor Manual de usuario
CASSIA PERSONAL SAFETY SENSOR
USER GUIDE
Personal Safety Sensor
3 Batteries Battery Cover
Opener Key User Guide
GETTING STARTED -- ENGLISH
I. INCLUDED IN PACKAGE
II. DETAILS
Alert LED
Alert Button
Battery Cover
Cover Slot
III. INSTALL BATTERY
1) To remove Battery Cover, insert Opener Key into Cover Slot.
2) Turn battery cover counter clockwise as shown in figure 1
below and remove.
3) Insert battery “+” side up between bracket holders.
4) With battery in place, insert Battery Cover in the unlocked
position shown in figure 1, then turn clockwise to the locked
position as shown in figure 2.
Fig. 1 Fig. 2
Unlock / Remove Battery Cover Lock Cover to Seal
IV. DOWNLOAD / INSTALL PERSONAL SAFETY APP
1) For Android (4.3+) device users -
i. tap on Google Play icon on phone
ii. search for “Cassia Personal Safety”
iii. tap on Install button, then Open when installed
2) For iOS (7.0+) device users (COMING SOON) -
i. tap on App Store icon on phone
ii. search for “Cassia Personal Safety”
iii. tap on Get button, then Open when installed
V. SETUP CASSIA PERSONAL SAFETY APP
1) Make sure Bluetooth is turned on in the Setting menu on
user’s smart phone
2) After launching the Cassia Personal Safety App, you must
accept the Subscriber Agreement before using App. Use of
App constitutes acceptance of the terms and use conditions
of the Personal Safety Sensor and App.
3) If you do not accept the terms of the Subscriber Agreement,
please cease using the product immediately.
4) Upon acceptance of Subscriber Agreement, proceed with the
onscreen instructions to setup user profile, enter emergency
contacts, and bind sensor to phone.
IMPORTANT: Make sure that Bluetooth is enabled in the
phones Settings menu in order to connect Sensor with phone.
VI. USE WITH CASSIA HUB
1) Please see Cassia Hub setup instructions to install the Hub.
No additional setup is required between Sensor & Hub.
2) If the Personal Safety Sensor is out-of-range of the user’s
phone, it will automatically attempt to communicate to Hub.
VII. ALERT DETECTED
1) When a Fall or Alert Button push is detected, the Alert LED on
the sensor will flash RED and then the phone will buzz or
make a sound indicating an alert has been detected.
2) The App will proceed to initiate an outbound call from your
cell phone to the first contact on your friends list as well as
send an SMS message to user’s contact list in App.
3) If the alert is a false alarm, user has 20 seconds to tap on
the Cancel Alarm button in App to cancel outbound call and
SMS message.
IMPORTANT REMINDERS
1) The Personal Safety Sensor App must remain running in the
background -- Do not close App.
2) The sensor must remain within approx. 30 feet of user’s
phone to remain connected to phone.
3) The cell phone must operate with an active cellular service.
4) If the user’s phone is unavailable and the Personal Safety
Sensor connects with a Cassia Hub, only SMS messages will
be sent from Hub to Contacts. No voice call will be initiated.
5) The Personal Safety Sensor must have a battery installed
with sufficient power level. Note: If LED is flashing RED in
normal operation mode, please replace the battery.
6) Press and hold Alert button for at least 0.5 seconds to
trigger an alert.
VIII. SPECIFICATIONS
40mm (D) 12mm (T); 15 grams
0~45℃/-20~70℃
4.0
+5dBm
-97dBm
3V/220mAh, CR2032
6 months
IP66
2AGF9CNK1000
Size/Weight:
Operating & Storage Temp.:
Bluetooth Standard:
Transmit Power:
Receiver Sensitivity:
Lithium Coin Battery:
Standby:
Waterproof Level:
FCC ID:
Federal Communications Commission (FCC) Statement
This device complies with FCC part 15 FCC Rules.
Operation is subject to the following two conditions:
1) This device may not cause harmful interference, and
2) This device must accept any interference, including
interference that may cause undesired operation of the
device.
FCC Warning
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1)This device may
not cause harmful interference, and (2)this device must accept
any interference received, including interference that may
cause undesired operation.
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
In addition to the FCC ID engraved on the battery door within
the device, the FCC ID will also be displayed on the user manual
in order to comply with FCC KDB 784748D01.
Beijing Cassia Networks Technology Co., Ltd.
www.cassianetworks.com
This device meets the FCC and IC requirements for RF
exposure in public or uncontrolled environments.
For additional assistance, please go to:
http://en.cassianetworks.com/pages/support. Or, contact
Tabla de contenidos
Idiomas:
