Cascade corporation IForks Manual de usuario

cascade

corporation

Cascade is a Registered Trademark of Cascade Corporation

SER MANUAL

Manual Number 6806956-R3

6806956-R3

ONTENTS

Page

OVERVIEW 1

WARNINGS & SAFETY MEASURES 2

INSTALLATION 3

USING DISPLAY 5

Functions 5

Other Features 6

USING iFORKS 7

Dos and Don'ts 7

Weighing Load - Basic 8

Weighing a Load - Net/Tare/Gross Weight 9

Weighing a Load - Add to the Total & Reset 11

Piece Counting 12

AUTO SHUT-OFF 13

BATTERIES 14

iForks Indication 14

Changing iFork Battery Packs 15

Changing Display Batteries 17

DISPLAY OPTIONS 18

User Settings 18

User Settings - Submenus 19

PRINTER OPTION 22

PERIODIC MAINTENANCE 24

6806956-R3

VERVIEW

FK0034.eps

Read through

user manual

Recharge or

change batteries

Install batteries

Review parts

Perform 2000 Hour

Maintenance

Install iForks

system on truck

Use system

This manual describes the installation and use of the iForks. Read this manual carefully. The installer must be

informed of the contents of this manual. Follow the contents of the manual precisely. Always do things in the

correct order. This manual should be kept on a safe and dry place. In case of damage or loss the user may

request a new copy of the manual from Cascade RAVAS.

26806956-R3

IP65

ARNINGS & SAFETY MEASURES

When using the iFork, please observe carefully the

instructions and guidelines contained in this manual.

Always perform each step in sequence. If any of the

instructions are not clear, contact Cascade RAVAS.

READ

CAREFULLY

- All safety regulations that apply on the truck remain valid and unchanged.

- No weighing operations are allowed if any persons or objects are in the vicinity; around, under or close to the load.

- Cascade RAVAS is not responsible for any physical harm done to the operator because of the presence of the indicator

in the cabin.

- Any modiﬁcations done to the system must be approved in writing from the supplier, prior to any work being completed.

- It is the sole responsibility of the purchaser to train their own employees in the proper use and maintenance of this

equipment.

- Do not operate this unit unless you have been fully trained of its capabilities.

- Check the accuracy of the scale on a regular basis to prevent faulty readings.

- Only trained and authorized personnel are allowed to service the scale.

- Always follow the operating, maintenance and repair instructions of this truck and ask the supplier when in doubt.

- Cascade RAVAS is not responsible for errors that occur due to incorrect weighings or inaccurate scales.

Should you have any further questions after reading this manual then you can contact Cascade RAVAS.

Min. 15°F (-10°C) Max. 105°F (40°C)

CAUTION: Do not Pressure Wash

IMPORTANT:Tampering or removing iForks NTEP Security wire or label will void NTEP Certification.

NSTALLATION

6806956-R3

FK0037.eps

FK0036.eps

FK0035.eps

Install iForks

IMPORTANT: Truck mast must be vertical.

A Remove standard forks.

B Unlock iForks.

C Install iForks.

Lock iForks

3Install battery packs into the iForks

A Lift up battery holder locking clip.

BPosition battery pack.

CClick into the battery holders.

DSecure the locking clips down.

IMPORTANT: If installing on fork positioner,

contact cascade.

NSTALLATION

46806956-R3

S13

FK0039.eps

FK0038.eps

7Install display bracket and support, if

required

Side Rail

Dashboard

Cabin Roof

Display

AInstall bracket to display.

BInstall bracket/display to the support.

6Locate and mount the display

Find a suitable location for readout and easy

access to display.

NOTE: If required, install batteries into display.

Refer to Batteries Section, "Changing Display

Batteries", page 17.

6806956-R3

SING DISPLAY

UFunctions

FK0040.eps

When appears: When appears:

Weight shown is in .44 lb (.2 kg) steps; only for

weight that ranges 0-441 lb (0-200 kg).

Weight shown is in 1.1 lb (.5 kg) steps; only for

weight that ranges 441-1102 lb (200-500 kg).

Weight shown is in 2.2 lb (1 kg) steps; only for

weight that ranges 1102-4850 lb (500-2200 kg).

Fork 1 relay setpoint 1 is activated.

Fork 2 relay setpoint 2 is activated.

When appears, the

weight shown is negative

The weighing system

(including load) is stable

The weight shown is

within the zero range

The display is showing

the net weight

Left of Display

Display

Button Entry ModeShort Key Press 3 Second Key Press

Right of DisplayMiddle of Display

When the following

appears:

Weight shown is

in kilograms

Weight shown is

in pounds

Amount displayed

is the number of

pieces on the scale

Low battery indicator

Enter (accept value)

Decrease the value

of the digit ﬂashing

Increase the value

of the digit ﬂashing

Shift to the next digit

on the left

Clear entry

Code Entry - A 5-digit code

useful for a weighing system

connected to peripheral

equipment for later processing.

Manual Tare - An entered tare

weight at any moment.

Check subtotal and print total.

Enter a piece weight - The

last used piece weight or an

entered value.

Toggle Units

Weighed load is added to total

weight. If printer is installed, a

printout is made.

Automatic Tare - Allows the

tare weights to be reset to

zero automatically. Added

and subtracted weights

can be determined.

Zero Setting - Manually

zeros the display

Sampling a piece weight -

Determined an unknown piece

weight by sampling a certain

number of pieces. Standard

sampling amount is 10 pieces.

On/Off

NOTE: Smaller loads are weighed with higher accuracy.

Example: If an original load with e2 range selected is

removed, and a smaller load qualiﬁed for e1 range, the

e2 range will remain selected until the forks are zeroed.

66806956-R3

SING DISPLAY

Select Weight Type

1000 kg➔lb

2205

FK0042.eps

Hold for 3 seconds

Wait 5 seconds to

switch units

Other Features

Display Menus

FK0041.eps

Weigh Mode

Options:

Net/Tare/Gross (Auto/Manual Tare)

Add weight/Subtotal weight/Total weight

Piece weight

Toggle units

Manual zero

On/off

User Settings

Auto shut-off time

Light intensity

Deactivate/Activate Com Port 1

Deactivate/Activate Com Port 2

Alibi Memory

6806956-R3

SING iFORKS

UDos & Don'ts

FK0044.eps

Wait 3-5 minutes

before using forks

Center load on forks and

pallet, load must be ﬂat

Wait for display

to zero

NTEP Temperature Range:

15° F (10° C) minimum

105°F (40° C) maximum

FK0045.eps

FK0046.eps

WEIGHING

PRIOR TO WEIGHING

FK0043.eps

Position to vertical

Level load to

Horizontal

Verify iForks are free of

obstacles prior to zeroing

For legal trade:

NTEP – ±5% (3°) Horizontal

OIML – ±5° Horizontal

Zero before each weighing

if display does not

automatically zero

86806956-R3

SING iFORKS

UWeighing a Load – Basic

FK0047.eps

Press the on/off key.

Wait 5 seconds.

Position load on

forks, raise forks

Press the

blue button

on each

battery pack

Display will zero.

If necessary, zero

manually.

1000

FK0048.eps

5Weigh load. Before next

weighing, check zero point.

To weigh a load: IMPORTANT:

If front face or bottom of iForks touches the•

load or pallet, it will not weigh correctly.

Unstable weight readings indicate debris•

between fork and fork shoe.

Tabla de contenidos

Otros manuales de Máquina elevadora de cascade corporation

cascade corporation

cascade corporation 35E Manual

cascade corporation

cascade corporation K Series Manual de usuario

cascade corporation

cascade corporation QFM Push/Pull E Series Manual de usuario

cascade corporation

cascade corporation F Series Manual de usuario

cascade corporation

cascade corporation K Series Manual de usuario

cascade corporation

cascade corporation 55H Manual de usuario

cascade corporation

cascade corporation 80G Manual de usuario

cascade corporation

cascade corporation Sideshifting Series Manual

cascade corporation

cascade corporation C Series Manual de usuario

cascade corporation

cascade corporation 35A Manual de usuario

cascade corporation

cascade corporation J Series Manual de usuario

cascade corporation

cascade corporation L Series Manual de usuario

cascade corporation

cascade corporation 782008-R3 Manual

cascade corporation

cascade corporation C Series Manual de usuario

cascade corporation

cascade corporation D Series Manual de usuario

cascade corporation

cascade corporation J Series Manual de usuario

Manuales populares de Máquina elevadora de otras marcas

Hyster

Hyster G108 Instrucciones de funcionamiento

ep ESL122 Manual de usuario

Cascade

Cascade D Series Manual

Daewoo

Daewoo D35S-2 Manual

Konecranes

Konecranes SMV 10-600B Manual de usuario

Cascade

Cascade G Series Manual de usuario

Manitou

Manitou MC 40 Powershift Manual de usuario

Hyundai

Hyundai 50DS-7E Manual de usuario

Pegasolift

Pegasolift W12 Instrucciones de montaje

Multi-Mover

Multi-Mover XXL 10 TO Manual de usuario

Noblelift

Noblelift PT 20I Manual

Lifter

Lifter QX 20 EVO Manual de usuario

Noblelift

Noblelift SPN22 Manual

Noblelift

Noblelift PT 27R Manual

Noblelift

Noblelift PS30RM Manual

Noblelift

Noblelift PS35LSL Manual

Noblelift

Noblelift PT E30 Manual

Still

Still CX-M 10 Manual de usuario

cascade corporation iForks Manual de usuario

Manuales populares de Máquina elevadora de otras marcas