Caple AS610BK Manual de usuario

Este manual sirve para los siguientes modelos

1

Tabla de contenidos

Otros manuales de Campana de ventilación de Caple

Caple

Caple CE1500 Manual de usuario

Caple

Caple ST850SS Manual de usuario

Caple

Caple BXC910 Manual

Caple

Caple Zalto ZAL48CO Manual de usuario

Caple

Caple Mi360 Manual de usuario

Caple

Caple BXI911 Manual de usuario

Caple

Caple CCH600SS Manual de usuario

Caple

Caple CE1122SS Manual de usuario

Caple

Caple BUCHB Manual de usuario

Caple

Caple CCH601BK Manual de usuario

Caple

Caple TSCH601 Manual de usuario

Caple

Caple DD600SS Manual de usuario

Caple

Caple DD921BK Manual de usuario

Caple

Caple 1MBUCH2 Manual de usuario

Caple

Caple BODY/DD600BK Manual de usuario

Caple

Caple BUCH Manual de usuario

Caple

Caple FSCHSS8 Manual de usuario

Caple

Caple D911BK Manual de usuario

Caple

Caple T80BUCHSS3 Manual de usuario

Caple

Caple Ceramica CR700 Manual de usuario

Caple

Caple Sirocco Si800 Manual de usuario

Caple

Caple ST523 Manual de usuario

Caple

Caple CE900 Manual de usuario

Caple

Caple INCH Manual de lista de piezas

Manuales populares de Campana de ventilación de otras marcas

emmeti

emmeti RECUPA MED A-140 Guía

Nibe

Nibe F135 Manual de usuario

Kuppersberg

Kuppersberg INTRO 60 Instrucciones de instalación y mantenimiento

Zephyr

Zephyr Spruce AK9834BS Guía de instalación

Hisense

Hisense MH6INBG Manual de usuario

Miele

Miele DA 1255 Manual de usuario

Broan

Broan 46000 Manual de usuario

GE

GE Profile PV977 Instrucciones originales

FALMEC

FALMEC FFRIA24W5FS Manual de usuario

Whirlpool

Whirlpool RH2600XL-1 SERIES Manual de usuario

Küppersbusch

Küppersbusch DX ISLA Manual de usuario

ETNA

ETNA AV360RVS Manual de usuario

JUNO

JUNO JDF603E6 Manual de usuario

Miele

Miele DA 6708 D Manual de usuario

Tricity Bendix

Tricity Bendix LE 150 Manual

AEG

AEG X68163BV1 Manual de usuario

AEG

AEG 125 D Manual de usuario

Smeg

Smeg KSEV97X Manual de usuario

Instruction manual for wall chimney hoods

Model codes: AS610BK / AS910BK

Contact Caple on 0844 800 3830 or for spare parts www.4caple.co.uk

1. For ease of installation, the light assembly should be fitted using a magnetic

screwdriver before the hood is installed on the wall.

2. The plastic cover is to protect the light assembly in transit. Once the light is

fitted to the hood, the plastic cover is easily removed by slackening the screws

and pulling the cover off.

4. For ease of installation, the light assembly should be fitted using a magnetic

screwdriver before the hood is installed on the wall.

5. The plastic cover is to protect the light assembly in transit. Once the light is

fitted to the hood, the plastic cover is easily removed by slackening the screws

and pulling the cover off.

Installing the Ductwork

1. Plan where the ductwork will run between the hood and the outside. The

hoods exhaust vertically but can be ducted to the rear behind the chimney

duct through an outside wall or vertically up through the ceiling to the

roof. A short straight duct run will produce the most air flow. Length and

elbows will reduce the efficiency of the blower.

2. Install a roof or wall cap. Connect a 6 round metal duct to the cap and

work backwards toward the hood. Ensure joints are completely sealed

with duct tape.

Fixing to the Wall

1. Before mounting the hood, plug in and test all functions for correct operation.

2. Remove the filters from the bottom of the hood to pre vent damage during the installation.

3. With assistance, hold the hood temporary in position ensuring the bottom is above the minimum clearance for

the cooking surface. Mark on the wall the holes for the two mounting screws.

4. Drill the holes and install the mounting bracket (1) . Use the appropriate screws and screw anchors for your

wall type (e.g. reinforced concrete, drywall, etc.). If necessary, prepare back wall with cross framing for secure

installation.

5. Mount the hood onto the bracket (2).

Connect a 6 aluminum duct tube (not included) to the exhaust piece using duct tape on all seals. (C)

7.

to roof cap

to wall cap

hood

decorative

chimney duct

38

39

40

Mounting bracket

Hook

1

2

mushroom tapping screw

3

6. Install two mushroom tapping screw into the wall.

Installing Guideline

Wall Mounted-Duct-out

1200~1700mm

650~700mm

Note:The above installation guideline for references only , please contact your local dealer

for a installation service.

Fixing the Decorative Chimney

Flu

1

2

3

.

.

.

Carefully losen but do not separate the telescopic chim ney duct pieces.

Arrange the electrical power supply within the dimen sions of the

decorative chimney duct.

Adjust the width of the support bracket to match the upper duct. Fix it

to the ceiling using the screws (B) so that it is centered in line with your

hood and at a distance from the ceiling indicated.

C

1. Separate lamp cover and left bracket by unscrewing.

2. Install right bracket to the cooker hood, then tighten the screws.

3. Connect two cables.

4. Re-Install left bracket and tighten the screws.