Capelec CAP2600 Manual de usuario
Rev A
1130, rue des Marels
FR 34000 MONTPELLIER
Phone: (33) 0 467 156 156
Fax: (33) 0 467 224 224
e-mail: contact@capelec.fr
www.capelec.fr
USER MANUAL
CAP2600 WORKSHOP™
Expert | Universal headlight beam tester
Edit: 30/07/19 | Rev A | Page: 1
Contents
Introduction...................................................................................................................................................2
Section 1: COMMISSIONING..........................................................................................................................3
I. Area of use..............................................................................................................................................3
II. Installation and commissioning.............................................................................................................3
2.1 Assembly instructions......................................................................................................................3
2.2 Configuration: first start up .............................................................................................................5
2.3 Computer links.................................................................................................................................5
2.4 Without a connection......................................................................................................................9
2.5 Customising and entering the garage header ...............................................................................10
Section 2: USER MANUAL ............................................................................................................................11
I. Overview...............................................................................................................................................11
II. Positioning the CAP2600 Workshop™.................................................................................................14
2.1 Vehicle preparation .......................................................................................................................14
2.2 Positioning in the vehicle length axis ............................................................................................15
2.3 Positioning the optical block in front of the headlamp.................................................................16
III. Lamp inspection..................................................................................................................................17
3.1 Inspection sequence......................................................................................................................17
3.2 Expert report..................................................................................................................................23
3.3 Advice when using the expert function.........................................................................................27
IV. Configuration......................................................................................................................................28
V. Care and maintenance recommendations..........................................................................................29
Edit: 30/07/19 | Rev A | Page: 2
Introduction
Thank you for having purchased the CAP2600 Workshop™ headlamp adjustment system. It has embedded
image processing technology developed by CAPELEC. It is a powerful expert system for adjusting and
checking lighting.
It is compatible with all headlamp lighting technologies installed on heavy and light road vehicles of the
M1, M2 and N1 categories (vehicles with a gross vehicle weight of less than 3.5 tonnes)
Please read this manual carefully before using the CAP2600 WORKSHOP™.
Keep it in a safe place to be able to consult it if necessary.
Note: The information in this document is subject to change without notice. CAPELEC cannot be held liable for direct or indirect
damage of any type, nor for losses or costs incurred through non compliant use.
WARNING
Precautions for use: the CAP2600 WORKSHOP™ lens must never be exposed to sunlight. The concentration of sunlight can
cause heating and a risk of damaging the equipment and/or burns.
Edit: 30/07/19 | Rev A | Page: 3
Section 1: COMMISSIONING
I. Area of use
Unlike other headlamp beam testers, the CAP2600 WORKSHOP™ does not need to define a work zone
and qualify it. It features innovating and unique technology: the "ANYWHERE" ground compensation
system. The CAP2600 WORKSHOP™ can therefore be used anywhere in your workshop.
II. Installation and commissioning
2.1 Assembly instructions
The CAP2600 WORKSHOP™ is delivered assembled and calibrated.
-Unpacking the CAP2600 WORKSHOP™
Edit: 30/07/19 | Rev A | Page: 4
-Cut the collar and keep the rubber stop.
-Caution: do not allow the metal cable to slip into the column
-Attach the metal cable onto the optical block
-Screw the upper stop to the top of the column
Edit: 30/07/19 | Rev A | Page: 5
2.2 Configuration: first start up
When you first activate the CAP2600 WORKSHOP™, you must select the language, the configuration
(France WS by default), and check the basic parameters: date, time and time zone.
2.3 Computer links
The CAP2600 WORKSHOP™ can be used with or without a computer connection. If you want to connect
your device, you can do so via the CAPELEC router or via your own WIFI network.
Connection to the preconfigured CAPELEC router
The CAP2600 WORKSHOP™ is delivered with a router configured for automatic WIFI connection as an
option. It is used to access the WEB interface and generate the expert report.
-Connect the router to the computer network (1), connect the power supply (2) and then turn on
the power (3)
1
2
3
Edit: 30/07/19 | Rev A | Page: 6
-Start the CAP2600 WORKSHOP™
-The WIFI icon (1) and the WEB interface address (2) appear on the home page
-Open a web browser and enter the displayed address
1
2
Edit: 30/07/19 | Rev A | Page: 7
-Add this page to the favourites
Connection to a WIFI network
The CAP2600 WORKSHOP™ can be connected to your WIFI network. It is used to access the WEB interface
and generate the expert report.
-Start the CAP2600 WORKSHOP™
-Go to "Config / Link" and enter the password "2345"
-Go to "Web server" and enter your SSID and key
Bookmark this page
Edit: 30/07/19 | Rev A | Page: 8
For networks with DHCP, keep the "IP AUTO" configuration, otherwise switch to static IP by
unchecking "IP AUTO" and enter an IP address
-Restart the CAP2600 WORKSHOP™
-The WIFI icon (1) and the WEB interface address (2) appear on the home page
-Open a web browser and enter the address
-Add this page to the favourites
1
2
Otros manuales para CAP2600
1
Tabla de contenidos
Otros manuales de Equipo de prueba de Capelec
Manuales populares de Equipo de prueba de otras marcas
SMART
SMART KANAAD SBT XTREME 3G Series Manual de usuario
Agilent Technologies
Agilent Technologies BERT Serial Manual de usuario
Agilent Technologies
Agilent Technologies N3280A Manual de usuario
Vernier
Vernier Go Direct Voltage Manual de usuario
Lifeloc
Lifeloc R.A.D.A.R. Manual de usuario
Fluke
Fluke T5-600 Instrucciones de funcionamiento e instalación
