Canon ScanFront 220 Manual técnico

Canon ScanFront 220/220P System Software Update

Instructions

ScanFront Version Up Procedure Version 1.0 Page

ScanFront 220/220P system software updates are distributed as .bin files. These files

can be downloaded from the Drivers and Downloads area of the Canon USA support web

site (http://www.usa.canon.com/html/download/sf220.html). Before you can download the

update file you will be prompted to input the 17 digit alphanumeric Product Key located on

the underside label of the ScanFront. When entering the Product Key be sure to use upper

case for any alpha characters in the key. Once the file is downloaded the device can be

updated using the same ScanFront Administrator Mode Web Menu that is used for

configuration and day to day management of the device. The following are the procedures for

applying these software updates.

The configured settings of the device should be backed up before performing a system

software update. Applying new system software will not erase configuration settings such as

user accounts, address book entries, job buttons, etc., but it is always advised to perform a

device backup before performing any software update. With that in mind this document starts

with instructions for backing up the configured settings on the ScanFront in the event those

settings need to be restored after the system software has been updated.

Canon ScanFront 220/220P System Software Update

Instructions

ScanFront Version Up Procedure Version 1.0 Page

ScanFront 220/220P Configuration Backup Procedure*

1. The IP address assigned to the ScanFront can be obtained at the device by clicking on the

Administrator Settings button on the main menu screen. You will need to enter the

administrator password if one has been assigned, and then click on the Network Setting

button. This will display the IP address, which is needed to connect to the ScanFront 220

Administration Mode Web Menu using a browser on any computer attached to the network;

* The Backup/Restore operation can also be performed at the ScanFront device. For more information please

refer to the detailed instructions on page 3-10 in Chapter 3 “ScanFront Setup” of the ScanFront 220/220P

Instruction manual.

Canon ScanFront 220/220P System Software Update

Instructions

ScanFront Version Up Procedure Version 1.0 Page

2. Once the IP address is obtained, launch an Internet Explorer session on a network attached

computer. Type the ScanFront IP address into the Internet Explorer address bar and then

click enter. You will be presented with the ScanFront 220 Web Menu login screen for the

device. Make sure the login screen is in Administrator Mode and not in User Mode.

Switching to Administrator Mode from User Mode can be done by clicking the To

Administrator Mode>> link in the upper right hand corner of the login page. If the upper

right hand corner link says To User Mode>> you are at the Administrator Mode login page

already. At that point you should enter the administrator password, and then click the Login

button;

Canon ScanFront 220/220P System Software Update

Instructions

ScanFront Version Up Procedure Version 1.0 Page

3. After logging in to the ScanFront Administrator Web Menu, click on the System Settings

menu item on the left side of the screen. Then click on the Backup/Restore sub menu item;

4. Click on the Backup All Settings… link. This will bring up the following dialog box

prompting you to Open or Save the file. You should choose the Save option;

Canon ScanFront 220/220P System Software Update

Instructions

ScanFront Version Up Procedure Version 1.0 Page

5. After clicking on the Save option you will be presented with a Save As dialog box where

you can specify a location and file name for the backup file;

You now have a file saved to your hard drive containing the ScanFront configured settings.

In the future this file can be applied to the device to restore the settings that existed at the

time the backup was made.

Canon ScanFront 220/220P System Software Update

Instructions

ScanFront Version Up Procedure Version 1.0 Page

ScanFront 220/220P Software Version Update Procedure

1. Before beginning you should make a note of the current version number displayed in the

upper right hand corner of ScanFront login screen. This can be compared with the version

displayed after applying the update to verify the update was successful.

You should also make sure that if you are using a laptop it is powered by the AC line. Power

cords to both the computer and ScanFront should be secure and fully inserted so that both the

computer and ScanFront don’t lose power during the upgrade process.

Canon ScanFront 220/220P System Software Update

Instructions

ScanFront Version Up Procedure Version 1.0 Page

2. Launch an Internet Explorer session on a network attached computer, type the ScanFront

IP address into the Internet Explorer address bar, and then click enter. You will be presented

with the ScanFront 220 Web Menu login screen for the device. Make sure the login screen is

in Administrator Mode and not in User Mode. Switching to Administrator Mode from User

Mode can be done by clicking the To Administrator Mode>> link in the upper right hand

corner of the login page. If the upper right hand corner link says To User Mode>> you are at

the Administrator Mode login page already. At that point you should enter the administrator

password, and then click the Login button;

Canon ScanFront 220/220P System Software Update

Instructions

ScanFront Version Up Procedure Version 1.0 Page

3. Once logged into the ScanFront Web Menu, click on the System Settings menu item on the

left side of the screen, then click on the Version Up sub menu item;

Canon ScanFront 220/220P System Software Update

Instructions

ScanFront Version Up Procedure Version 1.0 Page

4. Click the Browse button to navigate to the downloaded ScanFront system upgrade .bin file.

Once the update file path location is selected, click on the Version Up button to start

transferring the file to the ScanFront;

5. You will be prompted with a dialog box warning that once the file has been uploaded the

ScanFront will be updated and the process cannot be reverted. Click the OK button to start

the update process;

Canon ScanFront 220/220P System Software Update

Instructions

ScanFront Version Up Procedure Version 1.0 Page

6. It will take several minutes or more depending on the bandwidth of your network for the

update file to be uploaded to the ScanFront. During this time you will see the following

screen. A progress indicator will display the transfer status in the lower part of the Internet

Explorer window;

Otros manuales para ScanFront 220

Este manual sirve para los siguientes modelos

Otros manuales de Escáner de Canon

Canon

Canon IRIS IRIScan Desk 5 Pro Manual de usuario

Canon

Canon ImageFormula R10 Manual de usuario

Canon

Canon CanoScan D1230UF Manual de usuario

Canon

Canon imageFORMULA DR-6030C Manual de usuario

Canon

Canon CanoScan LiDE 80 Manual de usuario

Canon

Canon PS-7000 Manual de usuario

Canon

Canon CanoScan FS2720U Manual de usuario

Canon

Canon P-208 Manual de usuario

Canon

Canon CanoScan LiDE 70 Manual de usuario

Canon

Canon imageFORMULA P-215II Manual de usuario

Canon

Canon imageFORMULA DR-6030C Manual de usuario

Canon

Canon CanoScan LiDE 30 Manual de usuario

Canon

Canon IMAGECLASS MF4150 Manual de instalación y operación

Canon

Canon IRIScan Book 5 Wif Manual de usuario

Canon

Canon 3622B002 Manual de usuario

Canon

Canon CanoScan N676U Manual de usuario

Canon

Canon CanoScan LiDE 20 Manual de usuario

Canon

Canon imageFORMULA DR-1210C Manual de usuario

Canon

Canon CanoScan LiDE70 Manual de usuario

Canon

Canon imageFORMULA CR-135i II Manual de usuario

Canon

Canon CR-25 - imageFORMULA Desktop Check Scanner Manual de instalación y operación

Canon

Canon IRIScan Express 4 Manual de instrucciones

Canon

Canon DR-9050C - imageFORMULA - Document Scanner Manual de usuario

Canon

Canon DR-6050C - imageFORMULA - Document Scanner Manual

Manuales populares de Escáner de otras marcas

Plustek

Plustek Scanner Manual de usuario

Z/I Imaging

Z/I Imaging PhotoScan 2001 Manual de usuario

Renkforce

Renkforce DS100-5M Manual de usuario

Image Access

Image Access WideTEK A2 Manual de usuario

Fujitsu

Fujitsu FI-4860C2 Manual de usuario

GeoSlam

GeoSlam ZEB Horizon Instrucciones de instalación

Kodak

Kodak i5800 Scanner Manual de usuario

Kodak

Kodak i7300 Manual de usuario

Revopoint

Revopoint POP Manual de usuario

Fujitsu

Fujitsu fi-4860C Manual de usuario

Eddyfi Technologies

Eddyfi Technologies Floormap X Manual de usuario

Faselase

Faselase F6 Manual de usuario

Fujitsu

Fujitsu CardMinder Manual de usuario

Uniden

Uniden BC340CRS Manual de usuario

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Manual de usuario

Mustek

Mustek PageExpress 4800 Pro Manual de usuario

Optex

Optex 750830 Manual de usuario

Innova

Innova 5210 Manual de usuario