Canon 7215 - LV XGA LCD Projector Manual de usuario
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
LV-5210/7215/7210
EXPAND SERIAL COMMAND
FUNCTIONAL SPECIFICATION
Page1
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
CONTENTS
1. Overtview
2. Serial Interface Specification
2.1 Communication Specification
2.2 Connection
3. Note for communications
4. Name Definition
5. Functional Execution Command table
5.1 Image Command Table
5.2 PC Control Command Table
5.3 VIDEO Control Command Table
5.4 Input Control Command Table
5.5 Screen Command Table
5.6 Lamp Command Table
5.7 Sound Command Table
5.8 Setting Command Table
6. Status Read Command Table
6.1 IMAGE Status Read Command table
6.2 PC Status Read Command Table
6.3 VIDEO Status Read Command Table
6.4 Input Status Read Command Table
6.5 Screen Status Read Command Table
6.6 Lamp Status Read Command Table
6.7 Sound Status Read Command Table
6.8 Setting Status Read Command Table
6.9 Other Status Read Command Table
7. Error Code Table
8. Functional Execution Command
8.1 Format
8.2 Transfer Example
8.3 Operation Requirements
8.4 Image Command
8.4.1 CF_BRIGHT COMMAND
8.4.2 CF_CONT COMMAND
8.4.3 CF_COLOR COMMAND
8.4.4 CF_TINT COMMAND
8.4.5 CF_SHARP COMMAND
8.4.6 CAMMA COMMAND
Page2
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
8.4.7 WBAL COMMAND
8.4.8 COLTEMP COMMAND
8.4.9 PROGV COMMAND
8.4.10 IMGE COMMAND
8.4.11 CF IMAGE ADJ COMMAND
8.5 PC Control command
8.5.1 CF_FSYNC COMMAND
8.5.2 CF_TDOTS COMMAND
8.5.3 CF_CLAMP COMMAND
8.5.4 CF_H-POS COMMAND
8.5.5 CF_V-POS COMMAND
8.5.6 CF_DDOTS COMMAND
8.5.7 CF_DLINE COMMAND
8.5.8 CF_PC STORE COMMAND
8.5.9 CF_PC MODE FREE COMMAND
8.6 VIDEO Control Command
8.6.1 CF_AVDDOTS COMMAND
8.6.2 CF_AVDLINECOMMAND
8.6.3 CF_AVHPOS COMMAND
8.6.4 CF_AVVPOS COMMAND
8.6.5 CF_AVSERV COMMAND
8.7 Input Control Command
8.7.1 CF_INPUT COMMAND
8.7.2 CF_SOURCE COMMAND
8.7.3 CF_INPUT_%1_%2 COMMAND
8.7.4 CF_SYSTEM COMMAND
8.8 Screen Control Command
8.8.1 CF_SCREEN COMMAND
8.8.2 CF_FLSCREN COMMAND
8.8.3 CF_UE COMMAND
8.8.4 CF_CENT COMMAND
8.8.5 CF_KEYSTONE COMMAND
8.8.6 CF_KYSTNMODE COMMAND
8.9 Lamp Command
8.9.1 CF_LAMOPH COMMAND
8.9.2 CF_ALMP MODE COMMAND
8.10 Sound Command
8.10.1 CF_VOLUME COMMAND
8.10.2 CF_MUTE COMMAND
Page3
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
8.11 Setting Command
8.11.1 CF_BBACK COMMAND
8.11.2 CF_DISPCOMMAND
8.11.3 CF_LOGOCOMMAND
8.11.4 CF_CEILCOMMAND
8.11.5 CF_REARCOMMAND
8.11.6 CF_RCODE COMMAND
8.11.7 CF_LANGCOMMAND
8.11.8 CF_ON-STACOMMAND
8.11.9 CF_P-MANECOMMAND
8.11.10 CF_P-MANETIMECOMMAND
8.11.11 CF_FANSPEEDCOMMAND
8.11.12 KEYDISCOMMAND
8.11.13 TERMINALCOMMAND
8.11.14 STANDBYMODEOCOMMAND
8.11.15 POINTERCOMMAND
8.11.16 FDEFAULTCOMMAND
8.11.17 LOGOCAPTURECOMMAND
9. Status Read Command
9.1 Format
9.2 Transfer Example
9.3 Operation Requirement
9.4 IMAGE COMMAND
9.4.1 CR-BRIGHTCOMMAND
9.4.2 CR-CONTCOMMAND
9.4.3 CR-COLORCOMMAND
9.4.4 CR-TINTCOMMAND
9.4.5 CR-SHARPCOMMAND
9.4.6 CR-GAMMACOMMAND
9.4.7 CR-WBAL-RCOMMAND
9.4.8 CR-WBAL-GCOMMAND
9.4.9 CR-WBAL-BCOMMAND
9.4.10 CR-COLTEMPCOMMAND
9.4.11 CR-PROGVCOMMAND
9.4.12 CR-IMAGECOMMAND
9.4.13 CR-IMGGMD COMMAND
9.5 PC COMMAND
9.5.1 CR-FSYNC COMMAND
9.5.2 CR-TDOTS COMMAND
Page4
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
9.5.3 CR-CLAMP COMMAND
9.5.4 CR-H-POS COMMAND
9.5.5 CR-V-POS COMMAND
9.5.6 CR-DDOTS COMMAND
9.5.7 CR-DLINECOMMAND
9.5.8 CR-PC STORECOMMAND
9.5.9 CR-SET PC ADJ COMMAND
9.6 Video Command
9.6.1 CR_SERSYSCOMMAND
9.7 Input Command
9.7.1 CR-INPUTCOMMAND
9.7.2 CR-COURCECOMMAND
9.7.3 CR-INPUT_%1COMMAND
9.7.4 CR-SYSTEMCOMMAND
9.8 Screen Command
9.8.1 CR-SCREENCOMMAND
9.8.2 CR-FLSCRENCOMMAND
9.8.3 CR-TRUECOMMAND
9.8.4 CR-KYSTONMODECOMMAND
9.9 Lamp COMMAND
9.9.1 CR_LAMPREPLCOMMAND
9.9.2 CR-LAMPMODECOMMAND
9.9.3 CR-PROJECOMMAND
9.10 Sound Status COMMAND
9.10.1 CR-VOLUMECOMMAND
9.10.2 CR-MUTECOMMAND
9.11 Setting Status COMMAND
9.11.1 CR-BBACKCOMMAND
9.11.2 CR-DISPCOMMAND
9.11.3 CR-RCODECOMMAND
9.11.4 CR-LANGCOMMAND
9.11.5 CR-ON-STACOMMAND
9.11.6 CR-P-MANE COMMAND
9.11.7 CR-P-MANETIMECOMMAND
9.11.8 CR-FANSPEEDCOMMAND
9.11.9 CR-KEYDISCOMMAND
9.11.10 CR-TERMINALCOMMAND
9.11.11 CR-STANDBYMODECOMMAND
9.11.12 CR-POINTERCOMMAND
Page5
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
9.12 Other Status Read Command
9.12.1 CR-SIGNAL COMMAND
9.12.2 CR-VMUTECOMMAND
9.12.3 CR-FREEZECOMMAND
9.12.4 CR-PTIMERCOMMAND
9.12.5 CR-TEMPWARNCOMMAND
9.12.6 CR-TEMPFAILCOMMAND
Page6
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
1 Outview
1.1 This Functional Specification defines communication functions such as Wireless Imager for
LV-5210/7215/7210.
1.2 The Projector Firmware Ver.1.x-ready.
1.3 Commands are to communicate to such as Wireless Imager, but most commands control a
remote projector with PC installed RS232C. That’s why commands are defined as expand
serial commands
2 Serial Interface Specification
2.1 Communication Specification
Specification
Synchro System Asynchronou
Transmission
S
p
eed 9600 / 19200
Data Length 8 bit
Parity N/A
Stop Bit 1
Flow Control N/A
Note1) transfer rate: initial setting value is 19200
Note2) transfer rate can be changed by service MODE
2.2 Connection
Must use a dedicated serial cable that come with the projector for a connection to a
COMPUTER and a projector.
PC Projector
COM No.1 Control Port
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
CD
SG
RXD
TXD
DTR
DSR
RTS
CTS
RING
(D-Sub9Pin) (MiniDIN8Pin)
Page 7
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
3 Note for communications
3.1 The expand command is defined one Command/one line that starts ”C” and ends carriage
return (0x0D)
3.2 When a projector receives carriage return (0x0D), it starts decoding.
-Functional Execution
(Ex.) ”CF_BRIGHT_032” [CR]
-Status Read Command
(Ex.) “CR_RIGHT” [CR] Note) _means a space
3.3 When it takes more than one second to receive one Command, it does not execute the Command.
Since the projector has received the first data “C”, when it takes more than 1 second until the
projector receives a carriage return (0x0D), it clears information of buffer.
3.4 When a COMPUTER keeps sending some Command, it must wait sending next command after
100ms when the COMPUTER receives the return command.
More than 100ms
Command
PC Projector “CF_BRIGHT_032”CR Next Command
Projector PC “000” CR
Response
(A few ms -- 5s)
3.4.1 When a COMPUTER sends next command before receiving a return command, the
projector may not operate properly.
3.4.2 Except no response after 5 seconds
3.5 It takes about 5 seconds for internal initialization after plugging in AC. During this time it
cannot process command. Do not issue any commands.
4 Name Definition
4.1 Data from a controller to a projector is represented as COMMAND, and data from a projector to
a controller for the incoming command is represented as RESPONSE.
4.2 [CR]: Carriage Return Code
The Command ends carriage return code. Also response Command ends carriage return, too.
4.3 : Space Code
All space Code is indicated by (_).
4.4 %1: Parameter in Command
When there are some parameters, the parameters are defined as %2, %3…
4.5 %%%: Error Code from a projector
“000”: Normal Reception
See “ 7.Error Code Table “ for error number.
4.6 %a : Parameter for response from a projector
When there are a few parameters, the parameter defines as %b, %c…
Page8
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
5 Functional Execution Command Table
5.1 Image Command Table
Execute Command Item
CF_BRIGHT_%1 [CR] Set Brightness value
CF_CONT_%1 [CR] Set Contrast value
CF_COLOR_%1 [CR] Set Color value
CF_TINT_%1 [CR] Set Tint value
CF_SHARP_%1 [CR] Set Sharpness value
CF_GAMMA_%1 [CR] Set-GAMMA value
CF_WBAL-R_%1 [CR] Set White Balance Red value
CF_WBAL-G_%1 [CR] Set White Balance Green value
CF_WBAL-B_%1 [CR] Set White Balance Blue value
CF_COLTEMP_%1 [CR] Set Color Temp. value
CF_PROGV_%1 [CR] Set or Cancel for Progressive
CF_IMAGE_%1 [CR] Set Image MODE.
CF_IMAGEADJ_%1 [CR] Reset and store for Image Adjustment.
5.2 PC Control Command Table
Execute Command Item
CF_FSYNC_%1 [CR] Set Fine Sync value.
CF_TDOTS_%1 [CR] SetTotalDotsvalue.
CF_CLAMP_%1 [CR] Set Clamp value.
CF_H-POS_%1 [CR] SetHorizontalPositionvalue.
CF_V-POS_%1 [CR] SetVerticalPositionvalue.
CF_DDOTS_%1 [CR] SetDisplayDotsvalue.
CF_DLINE_%1 [CR] SetDisplayLinevalue.
CF_PCSTORE_%1 [CR] Store e current PC Adj. Status to MODE 1, 2, 3, 4, or 5.
CF_PCMODEFREE_%1 [CR] Reset MODE1, 2, 3, 4, and 5.
5.3 VIDEO Control Command Table
Execute Command Item
CF_AVDDOTS_%1 [CR] Set AV Horizontal Resolution Value
CF_AVDLINE_%1 [CR] Set AV Vertical Resolution Value
CF_AVHPOS_%1 [CR] Set AV Horizontal Position Value.
CF_AVVPOS_%1 [CR] Set AV Vertical Position Value.
CF_AVSERV_%1 [CR]
Reset AV Horizontal /Vertical Resolution that are set in
such as CF_AVDDOTS/CF_AVDLINE to default
setting.
5.4 Input Control Command Table
Execute Command Item
CF_INPUT_%1 [CR] Select Input.
CF_SOURCE_%1 [CR] Select Input Sauce.
CF_INPUT_%1_%2 [CR] Select Input and Source.
CF_SYSTEM_%1 [CR] Select System.
Page9
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
5.5 Screen Command Table
Execute Command Item
CF_SCREEN_%1 [CR] Select Screen size.
CF_FLSCREN_%1 [CR] Set and Cancel Full Screen.
CF_TRUE_%1 [CR] Set and Cancel True for Screen.
CF_DZCENT_%1 [CR] Cancel DIGITAL zooms.
CF_KEYSTONE_%1 [CR] Set Keystone
CF_KYSTNMODE_%1 [CR] Set Keystone store MODE
5.6 Lamp Command Table
Execute Command Item
CF_LAMPH_%1 [CR] Reset lamp total running time.
CF_LAMPMODE_%1 [CR] Select lamp MODE.
5.7 Sound Command Table
Execute Command Item
CF_VOLUME_%1 [CR] Set Volume value
CF_MUTE_%1 [CR] Control Sound Mute ON/OFF
5.8 Setting Command Table
Execute Command Item
CF_BBACK_%1 [CR] Set Blue Back function.
CF_DISP_%1 [CR] Set Display function.
CF_LOGO_%1 [CR] Set Logo function.
CF_CEIL_%1 [CR] Set Ceiling function.
CF_REAR_%1 [CR] Set Rear Function.
CF_RCODE_%1 [CR] Select Remote Control Reception Code.
CF_LANG_%1 [CR] Select OSD language.
CF_ON-STA_%1 [CR] Set Power ON Start Function.
CF_P-MANE_%1 [CR] Set Power management function.
CF_P-MANETIME_%1 [CR] Set Power management time
CF_FANSPEED_%1 [CR] Select Fan Speed.
CF_KEYDIS_%1 [CR] RC//ＫＥＹ inhibit
CF_TERMINAL_%1 [CR] Set TERMINAL.
CF_STANDBYMODE_%1 [CR] Set STANDBYMODE
CF_POINTER_%1_%2 [CR] Set POINTER
CF_FDEFAULT_%1 [CR] Set Factory Default
CF_LOGOCAPTURE_%1 [CR] Capture the current image on the screen.
Page 10
Otros manuales para 7215 - LV XGA LCD Projector
2
Este manual sirve para los siguientes modelos
4
Tabla de contenidos
Otros manuales de Proyector de Canon
Canon
Canon LV-5220 - Multimedia Projector SVGA Manual de usuario
Canon
Canon LV-5220 - Multimedia Projector SVGA Manual de usuario
Canon
Canon LV-7385 Manual de usuario
Canon
Canon WUX500ST Manual de instalación
Canon
Canon Vizcam 1000 Manual de usuario
Canon
Canon REALiS WUX4000 D Manual de usuario
Canon
Canon LV-8235 Manual de usuario
Canon
Canon LV-WU360 Manual de usuario
Canon
Canon RE-350 Manual de usuario
Canon
Canon LV-X4 Manual de usuario
Canon
Canon LV-5110U Manual de usuario
Canon
Canon LV-8235 UST Manual de usuario
Canon
Canon WUX10 - REALiS WUXGA LCOS Projector Manual de usuario
Canon
Canon Rayo S1 Manual de usuario
Canon
Canon LV 7490 Manual de usuario
Canon
Canon LDP-3070K Manual de usuario
Canon
Canon ReallS SX80 Manual de usuario
Canon
Canon RE-350 Manual de uso y mantenimiento
Canon
Canon LV-7545 Manual de usuario
Canon
Canon LV-7555 Manual de usuario
