Canon PIXMA MX922 Manual de usuario
1
Getting Your Multifunction
Back On Your Network
After A Router Or Network Change
PIXMA MX922
Mac OS
2
If any of the following situations exist
•You have replaced your Router or Access Point
•You want to use a different wireless network
•Router settings have been changed.
Please complete the following steps to apply the new configuration settings to your multifunction.*
*The procedure to reconfigure the printer will cause a new instance or listing of the printer in Print & Fax or Print & Scan. To avoid
possible confusion it is recommended to delete the printer listing prior to performing the reconfiguration procedure. Click here for
instructions.
1. To re-establish communication on the network after changing the router / Access Point or when connecting to a different network, the
settings on the Multifunction need to be changed. If you saved a copy of the setup file when you originally installed your printer you can
use it to run the setup. This file, “Mac-mx920-1_0-mcd.dmg” is located in the Downloads folder. Double-click the file, then the setup icon
to start the installation.
If you did not save the file to your computer when the printer was first installed, you can use the Setup CD-ROM to install. You will be
installing the printer the same way as the initial install.
Click here to access the Initial Setup Instructions.
Connecting to the Network
3
<< Previous Next >>
3. In the subsequent screen, enter the administrator name and password. Then click [OK].
2. Click Next to install the helper tool.
Connecting to the Wireless Network
4
<< Previous Next >>
4. If the following screen appears, click Start Setup Again
Connecting to the Wireless Network
Go to the next page
5
<< Previous Next >>
5. Continue following instructions. Click Network
Connection on Connection Method Selection
6. Click Wireless Connection
7. Follow any instructions and Click Connect to the
Network when the Printer Setup window appears .
8. Follow any instructions. Pay particular attention to the
instruction in the Setup Procedure Selection (3-1) if setup
detects a WPS access point. Continue to the next page for
important information on the Setup Procedure Selection. Do
not proceed past the Setup Procedure Selection (3-1) step
until reading the information on the next page.
Connecting to the Wireless Network
9. The printer automatically searches for access points that support WPS (Wi-Fi Protected Setup)*. If a WPS access point is detected, the Push
Button Method screen (shown below on left) will appear on the machine’s operation panel
*Unless you are absolutely sure your access point supports WPS and you are familiar with activating this on your access point, press the Stop
button on the printer’s operation panel and click on Other Methods on the Setup Procedure Selection screen (screenshot shown below)*.
If the Push Button Method is not shown on the printer’s operation panel(when no WPS access points have been detected), select Standard
setup on the printers operation panel, then click Other Methods on the Setup Procedure Selection screen
Connecting to the Wireless Network
6
<< Previous Next >>
If you selected the Push Button Method, continue to follow
any instructions until the Completion of Connection screen
appears. Click here to skip ahead to the Completion of
Connection.
If you selected Other Methods, please continue to the next
page for important information
Connecting to the Wireless Network
7
<< Previous Next >>
For Standard setup only
Select Standard setup on the Setup Procedure Selection screen (3-2)
Continue to next page before proceeding any further with setup
Connecting to the Wireless Network
8
<< Previous Next >>
Follow On-screen instructions. When you get to Step 4-2 and later in Step 4-4 ( screens shown below) you will need to know SSID and
password information*
Step 4-2 Step 4-4
*Unless you are absolutely certain of this information, please continue to the next page for information on locating /
verifying this information
Connecting to the Wireless Network
9
<< Previous Next >>
If you don't know your Access Point / Router name or SSID*, or the Passphrase or Network key for your wireless network, you can find this
information during Standard setup using the Setup CD-ROM or the downloaded files (Mini Master Setup or Master Setup).
*The terms 'SSID' and 'AccessPoint / Router' refer to a name used to identify the specific Access Point or Router. "Passphrase' and 'Network
Key' refer to a password required to prevent unauthorized access to communication.
Look for the Confirm the access point name or the Confirm the network key (automatic display) buttons during the setup procedure.
Clicking either of these buttons will give the needed information. On a Mac OS X system you may need to click 'Allow' on one or more
windows after clicking either of the above buttons. See example below of the Wireless Lan Setup Information window. (appearance varies
depending on Operating System). Use the provided information when selecting the Access Point / Router and for entering the Network
Key.
10
<< Previous Next >>Installing the Drivers
10. Continue to follow any instructions until the Setup Completion or Completion of Connection screen below is displayed. Network
connection setting is complete.
Click Next. Software will install. Continue to follow instructions until the Add Printer screen (shown on next page)
appears.
Otros manuales para PIXMA MX922
5
Tabla de contenidos
Otros manuales de Impresora de Canon
Canon
Canon PIXMA TS5110 Manual de usuario
Canon
Canon PIXMA TS6120 Guía de configuración
Canon
Canon PIXMA iP4920 Series Manual de usuario
Canon
Canon CX-G2400 Instrucciones de montaje
Canon
Canon TS3100 Series Manual de usuario
Canon
Canon pixma ix6800 series Guía de configuración
Canon
Canon Image Prograf PRO-2000 Manual de usuario
Canon
Canon S900 Manual de usuario
Canon
Canon Pixma PRO-100S series Manual de usuario
Canon
Canon laser Shot LBP 3300 Manual de usuario
Canon
Canon PIXMA MP970 Manual de usuario
Canon
Canon PIXMA MP240 Manual de usuario
Canon
Canon LBP-3200 Manual de instrucciones
Canon
Canon S450 Manual de usuario
Canon
Canon BJC-8500 Manual de usuario
Canon
Canon MultiPASS C2500 Manual de usuario
Canon
Canon PIXMA MX895 Manual de usuario
Canon
Canon Color imageCLASS MF8280Cw Manual de usuario
Canon
Canon MB5170 Manual de usuario
Canon
Canon imageCLASS D1320 Guía de seguridad
