Canon PIXMA iP1900 Manual de usuario
iP1900
Getting Started
Make sure to read this manual before using the printer. Please keep it in hand for future reference.
Symbols
■
The following symbols are used to mark important instructions.
Observe these instructions.
Instructions that must be observed for safe operation.
Instructions that, if ignored, could result in personal injury or
material damage.
Contents
Loading Paper
5
Install the Software
4
Install the FINE Cartridges
3
Turn the Power On
Descriptions for operations that take some time to complete.
Additional explanations.
2
Remove the Protective Material
1
After Installing the Printer
Model Number: K10328(iP1900)
Microsoft is a registered trademark of Microsoft Corporation.
Windows is a trademark or registered trademark of Microsoft Corporation in the U.S. and/or other countries.
Windows Vista is a trademark or registered trademark of Microsoft Corporation in the U.S. and/or other countries.
Macintosh and Mac are trademarks of Apple Inc., registered in the U.S. and other countries.
•
•
•
•
1
12 3 4 5
B
C
(A)
(B)
(B)
1
1
Remove the Protective Material
First, check the included items
Manuals
Setup CD-ROM (containing the drivers, applications and on-screen
manuals)
Warranty
•
•
•
Open the Cover (A), then remove the protective material (B).
Remove the protective sheets before opening the Cover.
Before turning on the printer, remove all the orange tapes.
•
•
Close the
Cover
(A) after removing the protective material (B).
power cordFINE cartridge
Color
Black
2
12 3 4 5
(1)
(2)
(A) (B)
2
23
1
Turn the Power On
Do NOT connect the USB cable at this stage.•
Plug in the power cord in the back of the
printer and connect the other end to
the wall outlet.
Press the ON button (A) to turn on the printer. Confirm that the POWER lamp (B) flashes
green.
3
1 2 34 5
(E)
(D)
(A)
3
12
Install the FINE Cartridges
Be sure to use the supplied FINE
Cartridges.
•
Open the Cover. Pull the orange protective tape (E) in the
direction of the arrow and remove it gently.
Be careful not to stain your hands or
surrounding work area with ink on the
removed protective tape.
•
The FINE Cartridge Holder (D) moves to the
left automatically. (This is where you install
the cartridge.)
Do not handle the FINE Cartridges
roughly such as applying them excessive
pressure or dropping them.
•
If the FINE Cartridge Holder returns to the
right, close the Cover and reopen it. If the
FINE Cartridge Holder does not come out
to the left, make sure that the power is
turned on.
•
4
34
3
Insert the Color FINE Cartridge into the right slot, and the Black one into the
left slot.
•
Insert the Color FINE Cartridge ( ) into the right slot ( ).
Insert the Black FINE Cartridge ( ) into the left slot ( ) in the same way.
Push up the cartridge until it clicks into place.
Do not knock the FINE Cartridge against the sides of the holder.•
Install the FINE Cartridges
5
1 2 34 5
B
C
(A)
(F)
5
Wait until the POWER lamp lights green (about 1 - 2 minutes) and go to the next step.•
Close the Cover (A).
Once you have installed the FINE Cartridges, do not remove them unnecessarily.•
If the alarm lamp (F) is fl ashing orange, make sure that the FINE Cartridges are correctly installed.•
6
4
Install the Software
Quit all running applications before installation.
You need to log on as the administrator (or a member of the Administrators
group).
Do not switch users during the installation process.
It may be necessary to restart your computer during the installation process.
Follow the on-screen instructions and click OK, and do not remove the Setup
CD-ROM during restarting.
The installation resumes from where it left off when your computer has been
restarted.
Mac OS 9, Mac OS X Classic environments, or Mac OS X v.10.3.8 or earlier
are not supported.
•
•
•
•
•
To use the printer by connecting it to a computer, software including the
drivers needs to be copied (installed) to the computer’s hard disk.
The screens below are based on Windows Vista operating system Ultimate
Edition (hereafter referred to as “Windows Vista“) and Mac OS X v.10.5.x.
Macintosh P.15
Windows P.7
7
51 2 3 4
(A)
1
2
3
12
If the Found New Hardware or
Found New Hardware Wizard
screen appears:
Click Cancel to quit the screen.
Proceed from .
Remove the USB cable
connected to your computer.
Press the ON button (A) to TURN OFF
THE PRINTER.
Turn on the computer, then insert the Setup
CD-ROM into the CD-ROM drive.
The setup program should run automatically.
Operating noise continues for about
15 seconds until the power turns off.
Make sure that the POWER lamp stops
fl ashing.
• If the program does not start automatically,
double-click the CD-ROM icon on the computer.
When the CD-ROM contents appear, double-
click MSETUP4.EXE.
•
Windows
Windows Vista
Windows XP/2000
Go to Step
Go to Step
The screen may close. In this case,
proceed from .
8
34
4
AutoPlay screen appears, click Run Msetup4.exe.User Account Control screen appears, click Continue.
If the same screen reappears in subsequent steps, click Continue.
Windows
Windows Vista Windows Vista
Otros manuales para PIXMA iP1900
1
Tabla de contenidos
Otros manuales de Impresora de Canon
Canon
Canon Selphy CP800 Manual de usuario
Canon
Canon imageCLASS LBP237dw Manual de usuario
Canon
Canon TS7450i Series Manual de usuario
Canon
Canon i950 Series Manual
Canon
Canon LBP351 Series Manual de usuario
Canon
Canon i860 Series Manual de usuario
Canon
Canon imageRUNNER C3326i Manual de usuario
Canon
Canon BJC-4000 Manual de usuario
Canon
Canon BJC-8000 Manual de usuario
Canon
Canon LBP3200 Series Manual de usuario
Canon
Canon iP6700D - PIXMA Color Inkjet Printer Manual de usuario
Canon
Canon imagePROGRAF iPF765 Manual de usuario
Canon
Canon PIXMA MG4120 Manual de uso y cuidado
Canon
Canon imagePRGRAF PRO1000 Manual de usuario
Canon
Canon Color imageCLASS MF8350Cdn Guía de seguridad
Canon
Canon imageRUNNER 1750i Manual de usuario
Canon
Canon MG6600 Series Manual de usuario
Canon
Canon LBP-3200 Manual de usuario
Canon
Canon PIXMA MP510 Manual de usuario
Canon
Canon LBP7750Cdn Manual de usuario
