Canon i860 Series Manual de usuario
REFILLING CANON PRINTERS
i860 and similar.
In the past I’ve owned several Epson, H.P, and one
Lexmark printer. With this Canon i860 I think I’ve found the
first consumer friendly printer, and that’s saying a lot.!!!!
This printer has an ink cartridge that can be removed
entirely for cleaning in about two seconds after the ink
tanks have been taken out, and it only take a couple of
seconds to remove all five of those. The cartridge case
can be easily cleaned by soaking in Windex or a mild
ammonia solution. How good can this get!!!!
As far as filling the ink tank with bulk ink, I’ve found there’s
a lot of confusion out there. I’ve found a way to fill these
tanks without leaking and with an easy technique, so this
is to share that with you.
TO BEGIN
Tools:You’ll need the following tools to do this job. Just
about everyone has these except maybe the glue gun.
Drill motor and a very small drill a bit larger than the
diameter of the fill needle.
Hot glue gun and glue (of course)
Bulk ink refilling kit (from Atlascopy.com--of course)
Ink (Same as above)
Newspapers (in case you make a mess first time)
And that’s about it!
THE INK TANKS
These aren’t cartridges, they’re tanks, which means there
is no sophisticated controllers built in, they’re only simple
tanks to hold ink. The ink comes out the bottom past a felt
lined round hole and into the cartridge (which does have
all those important controllers) and then to the paper.
The tanks have two internal spaces, one is filled with foam
and the other empty. There’s a transit space between the
two spaces for the ink to move from the empty space (a
reservoir) to the foam filled space. The computer uses
infra red technology to read the tanks and can report the
amount of ink remaining to you using the software “setup
utility). Another nice feature is the fact that the tanks are
clear plastic, so you can find out how low the ink is just by
taking out the tanks and looking at them.
Important: Don’t confuse the two black tanks! The large
tank “BK3e” is pigmented ink. It’s used primarily for text.
The smaller black tank “BK6” is dye based and is used for
photo. Don’t put pigmented ink into the small tank--it won’t
work! You may wind up buying a new cartridge!!!
HERE WE GO!!!
First, have the syringe laying down in front of you already
filled with the ink of choice, your rubber gloves on, paper
down on the table, and a sink nearby. You’ll need to
carefully clean the syringe after each fill in order to prevent
cross contamination. Have the drill handy to pick up with
the drill inserted. Have the glue gun hot and ready to go.
METHOD
You’ll need to drill two holes, one in each of these spaces,
on the top of each. Drill the first above the foam filled area
and slightly down into the foam to be sure there’s a clear
passage for venting. This prevents something called
“vapor locking” which won’t allow any ink to leave from the
bottom.
NEXT,
With your rubber gloves on, put your finger over the exit
hole on the bottom below the foam filled space. Hold it
tight! Now drill another hole on the top of the empty
reservoir near the front. You’ll see a slight dimpled spot
almost to the front. Drill there. Now you’re ready to insert
the ink. Pick up the syringe and fill the space almost to the
top. If there’s any ink at all on the top near the hole, wipe it
off with a paper towel, pick up the glue gun and spread a
bit of hot glue over and slightly around the hole. This is the
“fill hole”---not the vent hole over the foam area.
Continue to hold your finger over the exit till the glue sets
up and you’re done. How easy was that????
Once you’re set up it shouldn’t take more than fifteen or
twenty minutes to fill all the tanks even including cleanup.
It’ll go quicker after the first time as the holes are already
drilled. In future fills it’ll be necessary to clear the hole
each time over the reservoir in order for the needle to
enter. Generally that will mean using the drill again as the
glue will go down into the hole a bit.
If you don’t get a good seal with the glue over the fill hole,
ink will immediately begin to run out of the exit hole on the
bottom. I tried using electrical tape as others have
suggested, and even though it was applied very tightly, it
didn’t seal. The glue does, and is easy to use. Only
problem with it is the need to clear the fill hole each time
you want to refill. The tape would have been more
convenient, but that’s the way it goes!!!
Caveat:
I haven’t tried this with any other Canon printer so can’t
vouch for this method with any other than the i860. Seems
that it ought to work on any with this tank system though,
but you’ll have to try for yourselves.
Good printing :-)
Ted Johnson
Otros manuales para i860 Series
5
Tabla de contenidos
Otros manuales de Impresora de Canon
Canon
Canon PIXMA MP520 Manual de usuario
Canon
Canon 3433B016 Manual de usuario
Canon
Canon Selphy CP510 Manual de usuario
Canon
Canon imageCLASS X MF1643iF II Manual de usuario
Canon
Canon CR-206 Manual de uso y cuidado
Canon
Canon 2207C025 Manual de usuario
Canon
Canon imageCLASS MF628Cw Manual de usuario
Canon
Canon Ivy CLIQ+ Manual de usuario
Canon
Canon PIXMA MP568 Manual de usuario
Canon
Canon MG3600 series Manual de usuario
Canon
Canon g3000 series Manual de usuario
Canon
Canon UFR II Manual de usuario
Canon
Canon imagePRESS C1+ Manual de usuario
Canon
Canon SELPHY CP790 Manual de usuario
Canon
Canon imagePRESS C800 Series Manual de usuario
Canon
Canon ImageRUNNER 2422L Manual de usuario
Canon
Canon imageCLASS MF269dw Manual de usuario
Canon
Canon GP200 Manual de usuario
Canon
Canon PIXMA G5040 Guía de configuración
Canon
Canon LBP3010 Series Manual de usuario
