Canon i-SENSYS MF8280CW Manual de servicio
▲
Wireless LAN
Setting Guide
▲
Wireless LAN
Setting Guide
Read this guide before setting up the wireless LAN
This guide describes the wireless LAN set up procedure and problems encountered during the conguration
After you nish reading this guide store it in a safe place for future reference See the Getting Started for
machine installation and settings for connection methods other than the wireless LAN
Prepare for Wireless LAN Connection
P
Setting the Wireless LAN
P
Installing the Software
P
Troubleshooting
P
2
Prepare for Wireless LAN Connection
Step Check the Following First
Step Switch the Connection Method to Wireless LAN
1 Is the computer connected to the wireless
router properly
For more information see the instruction manual for the
network device you are using or contact the networking
device manufacturer
2 Have the network settings on the computer
been completed
If the computer is not properly congured you may not
use the wireless LAN connection even after completing
the following settings
NOTE
You cannot connect both a wired LAN and wireless
LAN at the same time In addition the machine is set
to the Wired LAN by default
When you connect to a network environment that is
not security protected your personal information may
be disclosed to third parties Please use caution
If you connect through a LAN in the oce contact
your network administrator
In this manual a wireless device that is accessed
from satellite terminals is generally called as
wireless router The term access point means
a master terminal on a wireless LAN that satellite
terminals access to
Internet Wireless Router
When proceeding from Connecting the Power Cord in the Getting Started
Proceed to Check Your Wireless Router on P
1
4 5
3
Press or to
highlight an option
2
3
Prepare for Wireless LAN Connection
Step Check Your Wireless Router
Select the method to set up the wireless LAN from the following two methods depending on the wireless router that
you are using
There is a button P Push Button Mode
This machine supports WPS WiFi Protected Setup You can
easily set up if your wireless router has a button and if the
following mark is on the wireless router
If you are not sure whether your wireless router supports WPS please see the
manual included in the product or contact the product manufacturer
There is no button P Manual Selection
If there is no button on your wireless router you may manually
select the SSID and complete the settings In this case you
need to specify the SSID and network key of your wireless router
See Check the SSID Network NameAccess Point Name and
Network Key P to learn how to nd out your SSID and network
key ?To set up connection by using WPS PIN code mode or manually entering the setup information
Setting Up Connection Using WPS PIN Code Mode in the eManual
Setting Up Connection by Specifying Detailed Settings in the eManual
When proceeding from Connecting the Power Cord in the Getting Started
Proceed to step 4 on P
Prepare for Wireless LAN Connection
Setting the Wireless LAN
Installing the Software
Troubleshooting
4
Setting the Wireless LAN
1
5
Press or to highlight WPS Push Button
Mode
2
Press or to highlight Network
Settings
6
Press to highlight Yes
3
Press or to highlight Wireless LAN
Settings
4
Move to the router
Push Button Mode
Setting via WPS
Read the instruction manual for your network device rst to learn how to congure the settings
If Do you want to enable the wireless LAN
is displayed press to highlight Yes and
then press OK
5
Setting the Wireless LAN
You should press the WPS button within
minutes after you select Yes in step 6
Press and hold the button until the WPS lamp
lights or blinks
The time that you should hold the button may vary
depending on the wireless router you are using
8
After the Connected screen is displayed
wait until the WiFi indicator stops blinking and
turns on
When an error message appears
Press OK to close the screen check whether
or not the WPS function of the wireless router is
correctly set and then retry the settings
If the access point cannot be detected even after
retrying see the following
When an Error Message Appears P
When checking the network connection
You can check if the machine is properly connected
to the network using a computer that is connected
to the same network
Checking that the Wireless LAN Setting is
Completed P
When setting an IP address manually
Setting IP Addresses in the eManual
Wait approximately minutes
after the connection is completed
The IP address is set during this time period
Move to the machine
Proceed to P
Prepare for Wireless LAN Connection
Setting the Wireless LAN
Installing the Software
Troubleshooting
6
Setting the Wireless LAN
1
2
Check the SSID Network NameAccess Point
Name and Network Key
Fill in the blanks on the right after checking one of the
following methods
Check a label attached on the wireless router
・・・
SSID ：XXXXXXXXXXXX：XXXXXXXXXXXXNetwork Key
Check using Canon MFLBP Wireless Setup
Assistant
Included in User Software CDROM which is supplied with the
machine
Checking SSID or Network Key for a Wireless Router
P
Press or to highlight Network
Settings
3
Press or to highlight Wireless LAN
Settings
4
Manual Selection
Setting by Selecting the SSID Network or Access Point
SSID
It is sometimes written as the name of network
or name of access point If there are multiple
SSIDs please write them all down
Network Key
It is sometimes written as PIN WEP key WPA
WPA passphrase PSK or preshared key
If Do you want to enable the wireless LAN is
displayed press to highlight Yes and then
press OK
7
Setting the Wireless LAN
7
9
8
1 Press to select the entry mode
2 Enter the network key using the numeric
keys
Press or to highlight the access point
you wrote down
If multiple matched SSIDs are displayed
select the ID that is listed rst the one with
the strongest signal
If no SSID has been found
Checking SSID or Network Key for a
Wireless Router P
Next Page
5
Press or to highlight SSID Settings
6
Press or to highlight Select Access
Point
If Cannot nd access point is displayed
When an Error Message Appears P
Prepare for Wireless LAN Connection
Setting the Wireless LAN
Installing the Software
Troubleshooting
Press to highlight Yes
8
Setting the Wireless LAN
After the Connected screen is displayed
wait until the WiFi indicator stops blinking
and turns on
Wait approximately minutes
after the connection is completed
The IP address is set during this time period
When an error message appears
Press OK to close the screen check whether the
network key is correct or not and then retry the
settings from step 5
If the access point cannot be detected even after
retrying see the following
When an Error Message Appears P
When setting IP address manually
Setting IP Addresses in the eManual
Proceed to P
9
Setting the Wireless LAN
3
2
8
Press or to highlight Network Information
Enter httpIP address that you have written
down in step 5 in the address eld and
then press Enter on your keyboard
Check that the screen of the Remote UI is
displayed
Press or to highlight IPv
1 6
5
Start a Web browser from the computer
Connection is completed
when the screen is displayed
If the screen is not displayed correctly
The Remote UI is not displayed P
Checking that the Wireless LAN Setting is Completed
4
Press or to highlight IP Address
Take note of the IP address
Proceed to P
Prepare for Wireless LAN Connection
Setting the Wireless LAN
Installing the Software
Troubleshooting
Status Monitor Status Monitor
10
4
3
2
Follow the instructions
on the screen to continue
The PC connection via the wireless
LAN is now complete
Select
Click
Take the CDROM out if necessary
Printer fax scanner drivers and MF Toolbox will
be installed
Select Custom Installation to install Presto
PageManager and the eManual
When the screen is not displayed correctly
Windows XPServer
Start menu Run enter DMInstexe OK
Windows VistaServer
Start menu Search programs and les or
Start Search enter DMInstexe press
the Enter key
Windows Server
Rightclick the lowerleft corner of the screen
Run enter DMinstexe OK
The CDROM drive name is indicated as D in this
manual
Click
1
User Software CDROM
▲
Installing the Software
Windows
Install the MF Drivers and the MF Toolbox Make sure that the machine is turned ON and log on to Windows as a
user with administrative privileges Shut down all applications that are running See MF Driver Installation Guide for
details about installation
NOTE
If you are operating in the IPv environment you may not be able to install the software following the procedures below See
Installing the MF Drivers on the WSD Network in the MF Driver Installation Guide
You cannot use the scan function in the IPv environment
Select ✔
Click
Otros manuales de Impresora de Canon
Canon
Canon imageCLASS LBP122dw Manual de usuario
Canon
Canon Color imageCLASS MF8080Cw Manual de usuario
Canon
Canon Pixma G2430 Manual de usuario
Canon
Canon laser Shot LBP 3300 Manual de usuario
Canon
Canon S200SP Manual de usuario
Canon
Canon LASER SHOT LBP-470 Manual de usuario
Canon
Canon MF1644iF Manual de usuario
Canon
Canon MG5100 series Manual de usuario
Canon
Canon IVY CLIQ+2 Manual de usuario
Canon
Canon PIXMA MG7500 Series Manual de usuario
Canon
Canon PIXMA MG3520 Instrucciones de instalación y mantenimiento
Canon
Canon BJC-2100 Series Manual de usuario
Canon
Canon iPF8400S Series Guía del usuario
Canon
Canon LBP113w Manual de usuario
Canon
Canon Color imageCLASS MF8280Cw Manual de usuario
Canon
Canon BJC-S830D Manual
Canon
Canon imagePROGRAF SD-21 Manual de usuario
Canon
Canon PIXMA MP160 Manual de usuario
Canon
Canon iP100 - PIXMA Color Inkjet Printer Manual
Canon
Canon MAXIFY MB2320 Manual de instrucciones
