C&S Controls LaserLight 2 Series Manual de usuario

LaserLight 2 Series

4.0” & 6.0” Remote Displays

TECHNICAL MANUAL

(Version 3.0)

P.O. Box 775 - Farmington, NH 03835

Tel: 603-755-3885

email: [email protected]

www.candscontrols.com

Authorized RLWS Distributor

Contents i

Contents

1.0 Introduction.................................................................................................................................. 1

1.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.2 Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1.3 Keypad. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1.4 Annunciators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2.0 Installation and Setup.................................................................................................................. 5

2.1 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.2 Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.2.1 Flange Mounting Brackets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.2.2 VESA Mounting Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.3 Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.3.1 AC Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.3.2 Serial Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.3.3 RF interference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.4 Laserlight2 CPU Board (PN 169279) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.4.1 20 mA Current Loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.4.2 RS-232 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.4.3 RS-422 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.4.4 Reset Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.4.5 Communicating with Indicators and LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.4.6 Ambient Light Sensor (177369) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.4.7 Decimal Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.5 Parts Kit, PN 92056 – All Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.6 Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.0 Configuration ............................................................................................................................ 16

3.1 Auto-Learn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

3.2 Catch-All Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

3.3 Setting Time and Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

3.4 Manual Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

3.5 Serial Communications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

3.6 Testing the Remote Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

3.6.1 Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

3.6.2 Digital Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

3.6.3 Digital Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

3.6.4 Loop Back . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

3.7 Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

3.8 Demand Print Displaying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

3.9 Serial Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

3.9.1 Remote Display Command Format:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

3.9.2 Set or Get the Digital I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

4.0 Options ....................................................................................................................................... 28

4.1 Fiber-Optic Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

4.2 Radio Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

4.3 Pole Mount Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

4.4 Visor Installation Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Specifications subject to change without notice.

Rice Lake Weighing Systems is an ISO 9001 registered company.

Version 3, May 03, 2017

Technical training seminars are available through Rice Lake Weighing Systems.

Course descriptions and dates can be viewed at www.ricelake.com/training

or obtained by calling 715-234-9171 and asking for the training department.

ii LaserLight2 Technical Manual

5.0 Maintenance .............................................................................................................................. 30

5.1 Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

5.2 LaserLight Remote Display Enclosure Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

5.3 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Rice Lake continually offers web-based video training on a growing selection

of product-related topics at no cost. Visit www.ricelake.com/webinars

Introduction 1

1.0 Introduction

This manual is intended for use by service technicians responsible for installing and servicing the LaserLight2

LED remote display.

Information contained within this manual is exclusively for units with CPU board,

PN 169279.

LaserLight 2 Technical Manual revision B or earlier, contains information

based on software Version 2 with CPU board, PN 166274.

This manual can be viewed and downloaded from the Rice Lake Weighing Systems website at

www.ricelake.com.

1.1 Ov erv iew

The LaserLight2 remote display features an ultra-bright LED display with a non-glare filtered lens for use in a

wide variety of applications. The LaserLight2 Series is available with a 6-digit display. It is designed to work with

most digital weight indicators, host computers, and peripherals using 20 mA current loop, RS-232 or RS-422 full

and half duplex communications.

The unique IntelliBright™feature uses a photo sensor to read ambient light and automatically adjusts the

LaserLight2 display between day and night settings.

The LaserLight2 enclosure provides easy access to internal components. The front panel swings open for

convenient setup and service. The enclosure has an external keypad which makes navigating configuration options

convenient using the arrows, Enter, Setup, Mode, Set and Learn keys.

Standard Features

The LaserLight2 display is available in 4" or 6" digit size. The LaserLight 4-SG display is a 4" digit size housed in

the larger enclosure (13" x 31"), with a 6" stop/go light. Both styles use an Auto-Learn function that automatically

determines the data format used by the attached indicator.

Additional standard features include:

• Six high-intensity red digits (double-row discrete LED)

• Auto learn mode of communication protocols

• Hold displayed weight (demand input)

• Software selectable standstill mode for no updates while in motion

• Durable weathertight IP66 enclosure

• Adjustable day/night intensity

• Software selectable time and date when the displayed weight is at zero and below.

• Non-glare contrast filtered lense

• Mirror (reverse image) feature

• RS-232, 20 mA and RS-422 communications

• Auto sensing 115/230 VAC power supply

• PEMs for VESA flat-wall mount or side-mounting flange

• Polyethylene breather vent inhibits internal moisture buildup

• Red, green and arrow lights in stop/go version

Optional Features

Optional features of the LaserLight2 remote display include:

•Pole mount kit

•ConnexLink radio interface

•Visor kit

•VESA flat wall mount kit

Important

2LaserLight2 Technical Manual

1.2 Sa f ety

Safety Symbol Definitions

Indicates a potentially hazardous situation that, if not avoided, could result in serious injury or death, and

includes hazards that are exposed when guards are removed.

Indicates a potentially hazardous situation that, if not avoided may result in minor or moderate injury.

Indicates information about procedures that, if not observed, could result in damage to equipment or

corruption to and loss of data.

General Safety

Do not operate or work on this equipment unless you have read and understand the instructions and

warnings in this Manual. Failure to follow the instructions or heed the warnings could result in injury or

death. Contact any Rice Lake Weighing Systems dealer for replacement manuals. Proper care is your

responsibility.

Failure to heed may result in serious injury or death.

Some procedures described in this manual require work inside the indicator enclosure. These procedures are to be

performed by qualified service personnel only.

Do not allow minors (children) or inexperienced persons to operate the LaserLight2.

Do not place fingers into slots or possible pinch points.

Do not use any load-bearing component that is worn beyond 5% of the original dimension.

Do not use this product if any of the components are cracked.

Do not exceed the rated load limit of the unit.

Do not make alterations or modifications to the unit.

Do not remove or obscure warning label (Figure 1-1).

Before opening the unit, ensure the power cord is disconnected from the outlet.

Test the operation of the ground fault circuit interrupter each time the sign is plugged in (UL version

only). To test the GFCI, plug in the LaserLight2 and press the TEST button. The LaserLight2 should

immediately turn off. If it does not, either the GFCI is mis-wired, a wiring problem in the same circuit or

the GFCI has malfunctioned and should be replaced. Pressing the RESET button will restore power to the

LaserLight2 or the circuit.

Figure 1-1. Safety Label PN 16861

WARNING

CAUTION

Important

WARNING

Important

Introduction 3

1.3 Keypad

The keypad, which is located on the bottom of the unit, allows for easy setup of the remote control.

Figure 1-2. LaserLight2 Keypad

Key Description

Used to navigate the configuration menu choices while in setup mode. The UP arrow exits the setup mode.

The arrow keys can also be used to set time and date after the SET key has been pressed.

Used to select a setting.

Used to enter the setup mode.

Used to increment a value for time and date after the SET key has been pressed. Alternatively, the time and

date value can be entered with the navigation keys.

Used to set time and date. Press SET to toggle to the next value of the time or date format. Press SET one

final time to exit the time and date setup.

Used to manually learn the incoming format. Use the navigation keys to move the displayed value to the

correct position. See Section 3.1 on page 16.

Table 1-1. Key Functions

SETUPENTER

MODE

SET

LEARN

ENTER

SETUP

MODE

SET

LEARN

4LaserLight2 Technical Manual

1.4 Annunciators

The LaserLight2 remote display uses a set of four high-intensity LED annunciators to provide additional

information about the value displayed. The serial default values for the annunciators are G & N and L & K.

Parameters for alternative values can be set under the serial menu, port 0.

The Stop/Go version of the LaserLight2 also has arrow and round light annunciators to indicate the different states

of the digital outputs. .

Figure 1-3. Front Panel Display – Stop-N-Go Model Shown

LED Description

GR Gross – Indicates the displayed weight is gross weight

NT Net – Indicates the displayed weight is net weight

lb Pounds – indicates units associated with the displayed value, represents primary and secondary units

kg Kilograms – indicates units associated with the displayed value, represents primary and secondary units

-- Red stop light, green go light and green arrow – indicates the traffic light state on the display. This feature

applies to only the LaserLight 4-SG.

See Section 3.9 on page 24 for additional information

Table 1-2. Annunciators

LED

annunciators

(showing GR for

gross and lb for

pound)

Installation and Setup 5

2.0 Installation and Setup

The LaserLight2 remote display is easily set up and configured. This section describes basic installation, AC

wiring, RS-232, RS-422 and 20 mA current loop connections. Once installation and set up is complete, see

Section 3.0 on page 16 for information on configuring the remote display.

The LaserLight2 has no on/off switch. Before opening the unit, ensure the power cord is disconnected

from the power outlet.

Use a wrist strap for grounding to protect components from electrostatic discharge (ESD) when working

inside the enclosure.

2.1 Unpacking

Immediately after unpacking, visually inspect the LaserLight2 for damage. If any parts were damaged in shipment,

notify Rice Lake Weighing Systems and the shipper immediately. The shipping carton contains the LaserLight2,

and the following components:

• Weather tight, IP66 rated enclosure with a CPU board and either mounting flanges or a VESA mount

• Installation manual

Remove the protective plastic on the lens of the LaserLight as it will obscure the display over time and

become very difficult to remove.

2.2 Wall Mounting

The LaserLight2 remote display can be mounted to any vertical surface or pole using 1/4" hardware or a VESA

mounting bracket for increased versatility.

2.2.1 Flange Mounting Brackets

The flange tab mounting comes in both 4" or 6" brackets.

Select a site and secure the remote display to a wall using included hardware and the mounting holes on the flange

tabs.

Figure 2-1. Side Mount Flange Brackets for 6"and 4"Models

An optional pole mounting kit is required when installing the remote display on a pole. The kit fits 4" - 8" poles

(see Section 4.3 on page 28).

WARNING

Important

175305

175306

1.58" (4.0 cm)

10"

(25.4 cm)

1.58" (4.0 cm)

20.3 cm)

6LaserLight2 Technical Manual

2.2.2 VESA Mounting Bracket

The VESAmount allows for a wide variety of mounting options to be compatible with the LaserLight2.

Figure 2-2. VESA Mounting Bracket

The four mounting PEMs on the LaserLight2 are threaded.

Refer to Figure 2-12 on page 15 and Table 2-8 on page 15 for applicable mounting bracket part numbers.

2.3 Wiring

The LaserLight2 remote display provides three cord grips located on the underside of the enclosure; one for the

suppliedA/C power cord, and two for serial communications. The LaserLight2 remote display comes pre-wired.

Ribbon cables connect the CPU board to the digit display boards. Only the serial communications cable must be

connected.

The LaserLight remote display has no on/off switch. Before opening the unit, ensure the power cord is

disconnected from the power outlet.

Use the following steps to open and wire the remote display in Section 2.3.1.

1. If the remote display is not open, loosen the captive screws located on the front of the remote display enclosure.

2. Pull the hinged display screen outward to open the enclosure.

2.3.1 AC Wiring

The LaserLight2 power supply can run on either 115 or 230 VAC. The AC wiring is run through the cord grip to a

3-positionAC terminal block bracket on the inside of the enclosure.

Figure 2-3. Power Supply Location and Wiring (non-UL Version Shown)

Wall Plate

Front View

Adaptor Plate

Side View

Adaptor Plate

0.38 in

(10 mm)

6.02 in

(153 mm) 1.02 in

(26 mm)

5.75 in

(146 mm)

5.00 in

(127 mm)

8.75 in

(222 mm)

7.87 in

(200 mm)

9.35 in

(237 mm) 7.87 in

(200 mm)

WARNING

Installation and Setup 7

Refer to Table 2-1 for AC wiring connections.

2.3.2 Serial Wiring

Serial communications are connected to the CPU board using removable screw terminal plugs on J6, J8 and J9 (Figure 2-5 on

page 9).

Use the following steps to connect the communications cable to the remote display.

1. Disconnect power and open the remote display by removing the captive screws on the front of the

enclosure and swing forward the hinged front cover.

2. Loosen the serial cable cord grip and push enough of the communications cable into the enclosure to allow

for attachment to the CPU board.

3. Strip 1/4" (0.65 cm) of insulation from the serial cable ends.

4. Make cable connections for RS-232, RS-422 or 20 mAcurrent loop communications as described in Table 2-2.

5. Remove excess cable from inside the enclosure. Tighten the serial cable cord grip.

2.3.3 RF interference

An EMI filter can be installed on the serial interface cable to eliminate RF interference (if necessary).

1. Run the serial wires through the EMI filter provided in the parts kit. See Table 2-3 on page 11.

2. Loop the serial wires around the EMI filter.

3. Use the provided plastic cable tie to secure the looped wires to the ferrite and the serial cable; this prevents

the ferrite from coming in contact with the CPU board.

Figure 2-4. Cylindrical Ferrite Placement for RF Interference

3-pin Terminal Block on Enclosure Back To Power Supply To Po we r Su pp l y

Pin Wire Color Pin UL Approved Unit

1 Neutral Blue or White 1 N

2 Hot Brown or Black 2 L

3 Ground Green or

Green/Yellow

Ground Tab

Table 2-1. AC Wiring Connections

Tabla de contenidos

Otros manuales de Monitor de C&S Controls

C&S Controls

C&S Controls Laser LT RD-1550 Manual de usuario

Manuales populares de Monitor de otras marcas

Linear Acoustic

Linear Acoustic LQ-1000 Manual de usuario

AOC

AOC I2579V Manual de usuario

Gateway

Gateway FPD1520 Manual de usuario

Furuno

Furuno Mu 120c Manual de usuario

Asus

Asus VB171D - 17" LCD Monitor Manual de usuario

Dell

Dell S2230MX Instrucciones de uso

Philips

Philips 107C64 Manual de usuario

Dell

Dell S2409WFP Manual de usuario

EverFocus

EverFocus EN-7517E Manual de usuario

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manual de usuario

Dell

Dell Precision 7680 Manual de instrucciones

LG 50PM1M - - 50" Plasma Panel Manual de usuario

Bosch

Bosch DDU 9 Manual de usuario

Acer

Acer A231HL Manual de usuario

Philips

Philips 86BDL4152T Manual de usuario

NEC

NEC AccuSync LCD5V Manual de usuario

Emay

Emay SleepO2 Manual de usuario

IBM

IBM 6360 Instrucciones de instalación