Campbell CS241DM Manual de usuario

08/2021

Campbell Scientific, Inc.

Table of contents

1. Introduction 1

2. Precautions 1

3. Initial inspection 1

4. QuickStart 2

5. Overview 4

6. Specifications 6

7. Installation 8

7.1 Wiring 8

7.2 Data logger programming 9

7.2.1 Programming 9

7.3 Placement on a photovoltaic (PV) module 10

7.4 Mounting/cable strain relief 10

7.4.1 Adhesive mounting strip 11

7.4.2 Cable strain relief 11

7.4.3 Extreme sealing tape 12

8. Operation 14

8.1 Electrical noisy environments 14

8.2 Long cable lengths 14

8.3 Modbus register map 14

8.4 Device Configuration Utility 16

9. Maintenance and troubleshooting 17

9.1 Maintenance 17

9.2 Troubleshooting 18

Appendix A. Importing Short Cut code into CRBasic Editor 19

Appendix B. Sensor material properties 20

B.1 3M F9473PC adhesive 20

Table of Contents - i

1. Introduction

The CS241DM temperature sensor uses a precision 1000 ohm Class A platinum resistance

thermometer (PRT) to measure temperature. It is designed for measuring the back-of-

photovoltaic (PV) module temperature but also can be used to measure the surface temperature

of other devices. The CS241DM has a digital RS-485 output that can be directly read by a

MeteoPV, CR6, CR1000X, or Modbus RTU RS-485 network. Other Campbell Scientific data

loggers can use an MD485 multidrop interface to read the RS-485 output.

NOTE:

This manual provides information only for CRBasic data loggers.

2. Precautions

lREAD AND UNDERSTAND the Safety section at the back of this manual.

lDo not use epoxy to secure the sensor head to a PV module.

lBefore mounting, the installers need to wash their hands and then clean the back of the PV

module or other device .

lPrying the sensor head off will likely damage both the sensor and PV module.

lProper strain relief of the cable is required after mounting the sensor to the measurement

surface (Mounting/cable strain relief (p. 10)).

lPlacement of the cable inside a rugged conduit is advisable for cable runs over 4.5 m (15 ft),

especially in locations subject to digging, mowing, traffic, power tools, animals, or lightning

strikes.

3. Initial inspection

lUpon receipt of the sensor, inspect the packaging and contents for damage. File damage

claims with the shipping company.

lThe model number and cable length are printed on a label at the connection end of the

cable. Check this information against the shipping documents to ensure the expected

product and cable length were received.

CS241DM PT-1000 Class A, Back-of-Module Temperature Sensor1

4. QuickStart

A video that describes data logger programming using Short Cut is available at:

www.campbellsci.com/videos/cr1000x-data logger-getting-started-program-part-3 . Short

Cut is an easy way to program your data logger to measure the sensor and assign data logger

wiring terminals. Short Cut is available as a download on www.campbellsci.com . It is included

in installations of LoggerNet, RTDAQ, or PC400.

The following procedure also shows using Short Cut to program the CS241DM.

1. Open Short Cut and click Create New Program.

2. Double-click the data logger model.

3. In the Available Sensors and Devices box, type CS241DM. You can also locate the sensor in

the Sensors > Temperature folder. Double click CS204DM/CS241DM. Type the RS-485

address; default address is the last two digits of the serial number. The CS241DM must have

a unique RS-485 address. The surface temperature defaults to degree C. This can be

changed by clicking the Temperature box and selecting one of the other options.

CS241DM PT-1000 Class A, Back-of-Module Temperature Sensor2

4. Click on the Wiring tab to see how the sensor is to be wired to the data logger. Click OK

after wiring the sensor.

5. Repeat steps three and four for other sensors you want to measure. Click Next.

6. In Output Setup, type the scan rate, a meaningful table name, and the Data Output Storage

Interval.

CS241DM PT-1000 Class A, Back-of-Module Temperature Sensor3

7. Select the measurement and its associated output option.

8. Click Finish and save the program. Send the program just created to the data logger if the

data logger is connected to the computer.

9. If the sensor is connected to the data logger, check the output of the sensor in the data

logger support software data display in LoggerNet, RTDAQ, or PC400 to make sure it is

making reasonable measurements.

5. Overview

The CS241DM is a surface mountable platinum resistive thermometer (PRT) that measures back-

of-module temperature for solar energy applications. It uses a precision PT-1000 Class A PRT to

provide the highest level of accuracy. To withstand the harsh treatment that commonly occurs

with meteorological station installation, the sensing element is safely housed inside a specially

designed self-adhesive aluminum disk (FIGURE 5-1 (p. 5)).

The disk protects the PRT, particularly during installation, and promotes heat transfer from the

surface. An adhesive tab on the disk fastens the sensor to the measurement surface.

The CS241DM includes a Campbell Scientific precision analog-to-digital, smart-sensor module

for making the measurements. The module design is optimized for the Class A PRT that

minimizes self-heating and wire resistance. Measurement electronics are surge protected with

1200 V isolation and environmentally protected with a rugged overmolding.

CS241DM PT-1000 Class A, Back-of-Module Temperature Sensor4

The CS241DM provides PV stakeholders with highly accurate back-of-module temperature, even

at long cable lengths, in power performance modeling and simulation of solar energy

applications. Back-of-module temperature is critical for any evaluation of effective irradiance and

power conversion.

FIGURE 5-1. CS241DM temperature sensor

Benefits and features:

lDesigned for optimal performance on bifacial PV module

lEasy installation

lNIST-traceable, serialized calibration certificate supplied with every sensor

lMeets or exceeds IEC 61724 Class A performance specifications

lPrecision PT-1000 Class A sensing element

lCompliant with IEC 60751, DIN EN 60751 (according to IEC 751)

lSlim design to minimize sensor impact on bifaciality (<2% of full-size cell area)

lThermal conductance greater than 600 W/(m2 K)

lMaximum sensor-to-module bonding

lHigh temperature rating to 150 °C

lInternal four-wire measurement with 24-bit A/D and precision resistor maximize

measurement accuracy

lCompatible with Campbell Scientific CRBasic data loggers: CR6, CR1000X, CR3000 (with

MD485), CR800 series (with MD485), CR300 series (with MD485), CR1000 (with MD485)

lEasily interfaces with the MeteoPV platform without programming

lConnects directly to a Modbus RTU RS-485 network

CS241DM PT-1000 Class A, Back-of-Module Temperature Sensor5

6. Specifications

Sensor: Precision 1000 ohm Class A platinum sensing element

Class A sensor accuracy: ± (0.15 + 0.002t) °C

Operating temperature range: –40 to 150 °C

Temperature coefficient: TCR = 3850 ppm/K

Long-term stability: Maximum R0 drift = 0.04% after 1000 hours at 400 °C

Temperature uncertainty: ±(0.3 to 0.4 °C) for the –40 to 100 °C measurement range

when using the CR1000X data logger

Disk diameter: 2.54 cm (1.0 in)

Height: 0.419 cm (0.165 in)

Disk material: Anodized aluminum

Shipping weight: 90.7 g (0.2 lb)

Analog-to-digitalmodule (DM): 24-bit ADC

A/D measurement

uncertainty: ±0.015 °C

Supply voltage: 5 to 30 VDC

Power consumption: 15 mA

Surge protection: 1200 V isolation

Environmental protection: Rugged overmolding

IP rating: IP68 rating (self certified); 1 m submersion for 90 min

Communications:

Protocol: Modbus RTU (over RS-485)

Format: 8 data bits, 1 stop bit, even parity as default (user

configurable)

Baud rate: 19200 bps as default (user-configurable)

Modbus ID: Last two digits of serial number as default (user-

configurable)

CS241DM PT-1000 Class A, Back-of-Module Temperature Sensor6

Approvals: Conforms with the Restriction of Hazardous Substances

Directive (RoHS2)

Compliance: View compliance documents at:

www.campbellsci.com/cs241dm

 Meets or exceeds IEC 61724 Class A performance

specifications

Industrial standards: Compliant with IEC 60751, DIN EN 60751,

Industrial Design (IEC Class 4) (according to IEC 751)

IP rating: IP68 rating (self certified): 1 m (3 ft) submersion for 90

minutes

EMC compliance: Conforms with Electromagnetic Compatibility Directive

(EMC)

RoHS2: Conforms with Restriction of Hazardous Substances

Directive (RoHS2)

POE compliance: POE compliant (802.3af) to 100 meters when installed per

recommendations in TIA TSB-184

CAT5e: Cable will meet CAT5e channel requirements to 100 meter

length

Sensor cable (sensor head-to-DM board)

Cable diameter: 0.216 cm (0.085 in)

Cable length: 0.9 m (3 ft)

Jacket material: White semi-gloss perfluoroalkoxy (PFA), insulated

Jacket rating: –75 to 250 °C

Minimum bend radius: 6 mm (0.25 in) at least 6 mm (0.25 in) away

from sensor disk

Connector: Circular plastic M12 , female 5-pin connector

Standard DM cable (DM board to pigtail)

Temperature rating: –40 to 105 °C

Overall cable diameter: 7.37 mm nominal ± 0.13 mm (0.29 inch nominal ± 0.005 in)

Conductor material: 22 AWG 19/0.0058 stranded tinned copper

Cable type: 4 twisted pairs twisted together and wrapped with clear

polyester tape to form a cable core

CS241DM PT-1000 Class A, Back-of-Module Temperature Sensor7

Connector: Circular, plastic, M12 male, 5-pin, A-coded connector

Jacket material: Thermoplastic elastomer, 1.07 mm (0.042 in) nominal wall

thickness (pressure)

Insulation material: High-density polyethylene 0.254 mm (0.01 in) nominal wall

thickness

Dielectric strength: 2000 V RMS

Approvals: UL AWM 2463 (80C 600V)

NEC (UL) TYPE PLTC

NEC (UL) TYPE CMX OUTDOOR – CM

CEC C(UL) TYPE CMX OUTDOOR – CM

PENNSYLVANIA D.E.P. – MSHA

7. Installation

If you are programming your data logger with Short Cut, skip and Data logger programming (p.

9). Short Cut does this work for you. See QuickStart (p. 2) for a Short Cut tutorial. This section

discusses the following:

7.1 Wiring 8

7.2 Data logger programming 9

7.3 Placement on a photovoltaic (PV) module 10

7.4 Mounting/cable strain relief 10

7.1 Wiring

The DM module is embedded in a short cable that attaches to the sensor head and has a 5-pin,

M12 female circular connector. A standard cable or a 3-twisted-pair shielded cable with a 5-pin

M12 male circular connector is used to attach the sensor to the station or data logger (Table 7-1

(p. 9)). Using connectors between the sensor head and the station or data logger cable allows in-

field sensor head replacement without disconnecting the cable from the data logger.

The following table provides sensor wiring and cable pin-out. Detailed information about the

cables are provided in the Specifications (p. 6). Sensor wiring is also available in the Device

Configuration Utility and the MeteoPV User Interface.

CS241DM PT-1000 Class A, Back-of-Module Temperature Sensor8

Tabla de contenidos

Otros manuales de Accesorios de Campbell

Campbell

Campbell HFT3 Manual de usuario

Campbell

Campbell SR50AT Manual de usuario

Campbell

Campbell SoilVUE 10 Manual de usuario

Campbell

Campbell SDM-CVO4 Manual de usuario

Campbell

Campbell SDMS40 Manual de usuario

Campbell

Campbell 0871LH1 Manual de usuario

Campbell

Campbell 253 Manual de usuario

Campbell

Campbell LWS-L Manual de usuario

Campbell

Campbell CRS451 Manual de usuario

Campbell

Campbell SnowVUE 10 Manual de usuario

Campbell

Campbell SR50 Manual de usuario

Campbell

Campbell CS100 Manual de usuario

Campbell

Campbell RainVUE SDI-12 Series Manual de usuario

Campbell

Campbell cs215 Manual de usuario

Campbell

Campbell 014A Manual de usuario

Campbell

Campbell CS100 Manual de usuario

Campbell

Campbell SR50A Series Manual de usuario

Campbell

Campbell EE181 Manual de usuario

Campbell

Campbell CS230 Manual de usuario

Campbell

Campbell BlackGlobe Manual de usuario

Campbell

Campbell Apogee Instruments CS310 Manual de usuario

Campbell

Campbell WXT520 Manual de usuario

Campbell

Campbell 385 Manual de usuario

Campbell

Campbell NR01 Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario