Campbell Hausfeld WS090001AV Instrucciones de instalación y funcionamiento

Additional Model Instructions Model WS090001AV

Addendum to Owner’s Manual

IN170138AV 2/99

BUILT TO LAST

Shielded Metal

Arc Welder

Description

Thank you for purchasing the

Campbell Hausfeld 70 amp Arc Welder,

Model #WS090001AV. This instruction

sheet is to be used in conjunction with

the standard owner’s manual included

with the welder (IN198904AV). Please

refer to this sheet for WS090001AV

assembly instructions.

Please read all

warning instructions in

the owner’s manual

before operating.

Components

The WS090001 comes with the

following additional equipment:

• Automatic amperage adjustment -

low position for 1/16” rods and

high position for 5/64” rods--for

ease of use.

• Cable storage clips (shown in

Handle Assembly) for safer storage

of welding cables.

Handle Assembly

1. Align the end holes on the handle

with the holes on top of the welder,

then secure with screws (Figure 1).

!NOTICE

MANUAL

2. Insert cable clips by pressing inward

on sides of clip and pushing into

the slots on front of handle as

shown in Figure 2. Repeat for

opposite side of handle.

Electrode Holder Assembly

(Refer to Figure 3)

1. Remove insulation handle from the

holder body by pulling the two

pieces apart.

2. Slide the other weld cable through

the handle.

3. Loosen the wire clamping screw

and slide the bare cord wire under

the clamp block. Tighten the

clamping screw and make sure the

wire is secure.

4. Slide the handle over the electrode

holder body and press to stop.

Make sure the handle is secure and

there is no exposed metal on the

holder.

Figure 3 - Electrode Holder

Figure 2

Figure 1

For parts, product & service information

visit www.campbellhausfeld.com

Ref. Part Number

No. Description for WS090001 Qty

1Electrode holder assembly - cord not included (includes ref. # 2-7) WC200000AV 1

2 Electrode holder handle - cord not included WC200001AV 1

3 Electrode holder body WC200002AV 1

4 Insulation cap WC200003AV 1

5 #10-24 x .5” machine screw * 1

6 #10-24 x 7/16” square nut * 1

7 Work clamp WC100300AV 1

8 Handle WC301300AV 1

9 #8-36 x 3/4” pan head screw * 2

10 Safety decal (right) DK404300AV 1

11 Safety decal (left) DK404400AV 1

12 Welding cable 6 AWG (6 ft) * 2

13 Power cord 14-3 AWG (6 ft) Type SJT WC000100AJ 1

14 High/off/low thermal indicator WC401000AV 1

15 Strain relief WC102000AV 2

16 Cord storage clip WC301301AV 2

* Standard hardware item, available at local hardware or welder supply store

Additional Model Instructions WS090001

For Replacement Parts, call 1-800-746-5641

Address parts correspondence to:

The Campbell Group

Attn: Parts Department

100 Production Drive

Harrison, Ohio 45030

Please provide following information:

- Model number

- Serial number (if any)

- Part description and number as

shown in parts list

Otros manuales de Sistema de soldadura de Campbell Hausfeld

Campbell Hausfeld

Campbell Hausfeld WG204498AJ Manual de usuario

Campbell Hausfeld

Campbell Hausfeld WF2034 Instrucciones de uso

Campbell Hausfeld

Campbell Hausfeld ARCITECH WS2100 Manual de servicio

Campbell Hausfeld

Campbell Hausfeld WG3000 Instrucciones de uso

Campbell Hausfeld

Campbell Hausfeld WT2531 Manual de usuario

Campbell Hausfeld

Campbell Hausfeld DW3130 Manual de servicio

Campbell Hausfeld

Campbell Hausfeld WG3080 Manual de servicio

Campbell Hausfeld

Campbell Hausfeld WG2060 Manual de servicio

Campbell Hausfeld

Campbell Hausfeld WK250000AV Manual de servicio

Campbell Hausfeld

Campbell Hausfeld WG3020 Instrucciones de uso

Campbell Hausfeld

Campbell Hausfeld WT5000 Manual

Campbell Hausfeld

Campbell Hausfeld WF2010 Instrucciones de uso

Campbell Hausfeld

Campbell Hausfeld WG3013 Manual de servicio

Campbell Hausfeld

Campbell Hausfeld WS2800 Instrucciones de uso

Campbell Hausfeld

Campbell Hausfeld WS0970 Manual de servicio

Campbell Hausfeld

Campbell Hausfeld WG2020 Manual de servicio

Campbell Hausfeld

Campbell Hausfeld WS0900 Manual de servicio

Campbell Hausfeld

Campbell Hausfeld WF2150 Manual de servicio

Campbell Hausfeld

Campbell Hausfeld WT2530 Manual de usuario

Campbell Hausfeld

Campbell Hausfeld IN972101AV Manual de servicio

Campbell Hausfeld

Campbell Hausfeld IN974200AV Manual de servicio

Campbell Hausfeld

Campbell Hausfeld WT2531 Manual de usuario

Campbell Hausfeld

Campbell Hausfeld WS0900 Instrucciones de uso

Campbell Hausfeld

Campbell Hausfeld Welder / Generator GW4500 Manual de servicio

Manuales populares de Sistema de soldadura de otras marcas

Berner

Berner PLASMACUT 54 Manual de usuario

Pro Spot

Pro Spot PR-155 Manual de usuario

Forney

Forney 210 Manual de usuario

Thermal Arc

Thermal Arc 400S Manual de usuario

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manual de usuario

GYS

GYS PROTIG 201 AC/DC Manual de usuario

TAFA

TAFA 30*8B35 Manual de usuario

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manual de usuario

ESAB

ESAB Buddy Arc 145 Manual de usuario

CIGWELD

CIGWELD 636804 Guía rápida

Red-D-Arc

Red-D-Arc DC-400 Manual de usuario

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manual de usuario

Elettro

Elettro HI-MIG 3000 SYNERGIC Manual de usuario

WIA

WIA Weldmatic 270 CP132-2 Manual de usuario

Sonics

Sonics H520T Manual de usuario

Miller

Miller Big Blue 400D Manual de usuario

NewArc

NewArc RT2000 Guía de inicio rápido

Hypertherm

Hypertherm powermax1000 Manual de usuario