CAME ATI-P3 Manual de usuario

CAME.COM/UK

Ati-P3 kit

QUICK SETUP GUIDE

Typical gate setup & geometry

Gate motor manual release

Kit wiring diagram

Control panel guide & safety

Complete kit for a pair of swing gates

with leaves up to 3m wide

TO BE READ IN CONJUNCTION WITH THE FULL INSTRUCTION MANUAL

CONTENTS

DIR10

Pair of Photocells

AF43S

Radio Frequency Card

top-a433n

Tuned Antenna

ZA3P

Control Panel

A3000A

Motor

ATI-P3: KIT CONTENTS

topd4Fks

Fixed code Transmitter

1Kit Contents

2Safety Instructions

3Typical Gate Setup

4Geometry

5Manual Release Instructions

6Kit Wiring Diagram

7Control Panel:

Quick Start Guide

8Control Panel:

Programming Transmitters

9Control Panel: Safety

10 Optional Accessories

SAFETY INSTRUCTIONS

When correctly installed in compliance to installation instructions and adhering to all

current electrical, mechanical and manufacturer regulations, your automation system

will provide a high degree of safety and problem free operation.

Please take note of the following warnings that must be followed in order to

prevent accidents during your gate operation:

• Do not allow children to play near the gate.

• Keep all remote control operating devices out of the reach of children.

• Do not pass through the gate whilst in operation. Wait until they are fully open before passing through.

• Do not stop unnecessarily when passing through the gate.

• Keep feet away from the bottom of the gate during operation.

• Do not operate the gate by remote control unless they are in view.

• Do not attempt to block or interfere with the gate movement during operation.

• Under no circumstances should you attempt to modify the gate automation system.

• Ensure that your gate is serviced at 3 to 12 month intervals (dependent on number of openings) by your installation/

maintenance company.

• Report any signs of malfunction to your installation/maintenance company immediately.

• In the case of malfunction, isolate the power supply, release any additional locking mechanism, manually open the

gate (see manual release instruction booklet) and call your installation/maintenance company.

• If you are in any doubt regarding the operation of your gate, call your installation/maintenance company.

ATI: TYPICAL GATE SETUP

OUTSIDE OF GATES

INSIDE OF GATES

1ATI Motor 4Flashing Light (optional) 72nd set of Photocells (optional)

2Control Panel 5Selector Keypad (optional) 8Mechanical End Stop (not supplied)

3Reception Antenna 6Photocells (on outside of gate posts) 9Photocell column (optional accessory)

CONTROL PANEL

PHOTOCELLS

• The control panel should be mounted in an accessible position and not directly behind the gates, to avoid a

potential crushing hazard.

• Use cable glands to connect the devices to the control panel. One of these must be used exclusively for the

power supply cable.

• All holes should be sealed to avoid ingression and maintain the IP54 protection rating.

Only a competent service provider should open the enclosure

and adjust the settings.

• The photocells are used in pairs, one transmitter and one receiver.

• They should be installed between 500-600mm from the ground, facing each other.

• Power for the photocells is taken from the control panel 24v AC.

• The maximum range of the photocell should always be observed.

When the photocell beam is broken, the control panel can be programmed on how to react.

Please see ‘Safety’ section for more information.

ATI-P3: GEOMETRY

• The greater the motor angle, the greater

the opening speed and the slower the

gear motor’s thrust.

• The smaller the motor angle, the slower

the opening speed and the greater the

gear motor’s thrust.

Preliminary checks

Side hung gate GEOMETRY

Tick

1. Check that the gate structure is sturdy enough, the hinges work eciently and that there is

no friction between the ﬁxed and moving parts

2. Make sure that measurement Cdoes not exceed the value shown in the reference table

3. Make sure that you have ﬁtted opening and closing mechanical gate stops

OUTward OPENING gates

For outward opening gate geometry

please refer to the full Installation Manual.

Bushing

Back swivel-

joint

• Lubricate the bushing and ﬁt it into one of the holes on the post bracket.

• The bracket holes allow the opening angle to be changed.

Pillar

Hinge

Leaf - closed

position

Opening A (mm) B (mm) C (mm) E (mm)

90°130 130 60 720

120°130 110 50 720

ATI: MANUAL RELEASE

The ATI worm drive swing gate operators have a manual release lock beneath a hatch on

the top of the motors.

To manually release the gates:

Basic Maintenance: Hints & Tips

• Slide back manual release cover & spray locking

mechanism with suitable penetrating lubricant.

• Lubricate gate hinges.

• Manually release the gates at least once per month.

ALWAYS isolate the power supply as

instructed by your installer (even in a

power cut).

Release any additional locking

device ﬁtted to the gate (eg. electric

lock etc).

1. Raise the door covering the lock A.

2. Insert the key Band turn 180° clockwise C, which immediately releases gate.

3. With your other hand ﬁrmly open the gate. The gate should be manually released. Now fully open the gate carefully at

the same speed as the automatic operator.

4. To re-engage, close the gate and turn the key back to its original position. Attempt to manually move the gate to

ensure it is fully engaged.

a CB

ATI-P3: wiring diagram

ATI A3000A

Gate motors

Cable/length

1m - 20m = 3 Core 1.5mm

20m - 30m = 3 Core 2.5mm

L N U V W X Y E E3 10 11 S 1 2 3 3P 457 2 C1 CX B1 B2TS 10

L1T CT 0 12 24

L2T

2FC1 FA2 FC2

FA1

L2T L1T1 2 3 4

012 24

ZA3P

Control Panel

+ -

10 2 TX C NC TX 2

RX TX

DIR

Photocells

Cable/length

RX 4 Core 0.5mm Flex

TX 4 Core 0.5mm Flex

1m - 30m

AF43S

Plug-in

TOP-A433N

Antenna

Cable/length

RG58

Max. 5m

Mains Supply

230 V AC

Cable/length

1m - 20m = 3 Core 1.5mm

20m - 30m = 3 Core 2.5mm

The Earth cable should

be connected to the

motor chassis.

ZA3P: QUICK START GUIDE

Important!

The installation must be carried out

by skilled and qualified personnel

Should the gates not operate as suggested above,

call CAME helpline 0115 921 0430 for technical support.

Safety inputs should now be configured and the

gate force tested as required. Please refer to the

full manual to complete the commissioning.

Ensure the wiring is complete (refer to the wiring diagram) & any required physical stops are set before

commencing with programming Tick

1. Power on the control panel.

2. Disable total stop – Permanent link wire between terminal 1& 2.

3. If no safety device has been connected to the C1 terminal then disable the safety input C1 -

Permanent link wire between terminal 2& C1.

4. Disable safety input CX – Dip switch 8on.

5. Set all other dip switches off.

6. Check the motor directions

Enable maintained action – Dip switch 6on.

Hold a wire between terminal 2& 3.

The gates should open, if not reverse the motor cables relating to the motor that is closing

for motor 2 (Connections X, Y)

for motor 1 (connections U, V)

Disable maintained action – Dip switch 6off

7. Set the TRM2 potentiometer all the way to minus (Anticlockwise).

8. Adjust the TL potentiometer to the 4 O’clock position

9. Check the gate operation by pulsing across connections 2& 4, the gate will close.

Potentiometers Dip Switches

ZA3P: transmitters

Should the transmitter not operate as suggested above,

call CAME helpline 0115 921 0430 for technical support.

add a transmitter button

1. Press and hold the CH1 button, the PROG. LED starts ﬂashing rapidly.

2. While keeping the CH1 button held down press and release a button on a transmitter

The PROG. LED goes solid to signal the successful saving of the code.

3. Release the CH1 key.

A maximum of 25 individual buttons can be saved.

remove all transmitters

1. Press and hold the CH1 and CH2 buttons simultaneously until the PROG. LED stays lit

All previously saved transmitter buttons will be removed from the memory of the control board.

L N U V W X Y E E3 10 11 S 1 2 3 3P 457 2 C1 CX B1 B2TS 10

L1T CT 0 12 24

L2T

2FC1 FA2 FC2

FA1

L2T L1T1 2 3 4

012 24

L N U V W X Y E E3 10 11 S 1 2 3 3P 457 2 C1 CX B1 B2TS 10

L1T CT 0 12 24

L2T

2FC1 FA2 FC2

FA1

L2T L1T1 2 3 4

012 24

Ensure the AF card is ﬁtted (refer to the wiring diagram).

ATI-P3: ACCESSORIES

For more kit accessories please contact Sales on 0115 9210 430

ZA3P: SAFETY

C1 REOPENING DURING CLOSING

• When the automation is in its closing cycle and the safety circuit is triggered the automation will stop and reverse its motion until it reaches its

fully open position again.

• If the auto closing option is enabled and the safety is no longer triggered the auto closing countdown will commence, once completed the

automation will start the closing cycle again.

• If the auto closing option is not enabled the automation will return to the fully open position awaiting another activation from a command device.

FUNCTIONS > C1 Input, CX Input

SAFETY INPUTS

CX RECLOSING DURING OPENING

• When the automation is in its opening cycle and the safety circuit is triggered the automation will stop and reverse its motion until it reaches its

fully closed position again.

• Once the automation has reached the fully closed position it will require another activation from a command device to restart.

CX PARTIAL STOP

• When the automation is in its opening cycle and the safety circuit is triggered the automation will stop.

• If the auto closing option is enabled and the safety is no longer triggered the auto closing countdown will commence, once completed the

automation will start closing the device.

If during the reverse motion a diﬀerent safety is triggered the automation will perform the appropriate action for the new triggered

safety, should multiple safeties be triggered at the same time the automation will be halted at its current position.

The above sequence will be attempted 3 times before the automation is halted, the automation will then

require activation from a command device to restart.

Otros manuales de Abridor de puerta de CAME

CAME

CAME FROG PLUS Series Manual de usuario

CAME

CAME ATS-P3 KIT Manual de usuario

CAME

CAME FROG A Manual de usuario

CAME

CAME BXL04AGS Manual de usuario

CAME

CAME FA01802M4A Manual de usuario

CAME

CAME BKS22TLS Manual de usuario

CAME

CAME A4366 Manual de usuario

CAME

CAME AMICO Series A1824 Manual de usuario

CAME

CAME FA40230 Manual de usuario

CAME

CAME Frog-A 24U Manual de usuario

CAME

CAME BXV1000GF Manual de usuario

CAME

CAME ZCX10 Manual de usuario

CAME

CAME BKV Series Manual de usuario

CAME

CAME v6000 Manual de usuario

CAME

CAME H SERIES Manual de usuario

CAME

CAME Ferni Series Manual de usuario

CAME

CAME F7000 Manual de usuario

CAME

CAME FA70230CB Manual de usuario

CAME

CAME BX-246V Manual de usuario

CAME

CAME FROG-A Manual de usuario

CAME

CAME BKV2000P Manual de usuario

CAME

CAME FA4024CB Manual de usuario

CAME

CAME BX Series Manual de usuario

CAME

CAME Ati-S3 Manual de usuario

Manuales populares de Abridor de puerta de otras marcas

Elite

Elite CSW200UL Manual de usuario

SOMFY

SOMFY FX230 Manual de usuario

Aprimatic

Aprimatic ONDA 500 Manual de usuario

Turnstiles

Turnstiles FSW 900 Manual de usuario

Erreka

Erreka BUL BL33 Instrucciones de funcionamiento

Erreka

Erreka VULCAN S Manual de usuario

Beninca

Beninca R1-2 WBV Manual de usuario

Erreka

Erreka VULCAN D Manual de usuario

Motorline professional

Motorline professional FORT Manual de instrucciones

Beninca

Beninca BOB5024 Manual de usuario

AGA

AGA GATEMASTER 900 HD Manual de usuario

Chamberlain

Chamberlain MotorLift HC280ML Manual de usuario

SOMFY

SOMFY Dexxo RTS Pro Manual de usuario

Cardin

Cardin BL Series Manual de usuario

Westfalia

Westfalia 85 27 06 Manual de usuario

Extel

Extel VERA Manual de usuario

Comunello Automation

Comunello Automation ABACUS 220 Manual de usuario

Mighty Mule

Mighty Mule 200 E-Z GATE OPENER UL325 SERIES Manual de usuario