Cambridge Audio Evo Manual de usuario
1
Evo - All In One Player
Manual Generated: 03/06/2021 - 16:39
Table of Contents
Evo - All In One Player 2
Front panel controls 3
Evo display 4
Evo 150 rear panel connections 6
Evo 75 rear panel connections 8
Remote control 10
Replaceable side panel 14
Getting connected 15
StreamMagic app - Setup 21
Google Home / Chromecast built-in 22
Bluetooth source 23
AirPlay 24
Spotify Connect 25
Bluetooth output 26
MQA (Master Quality Authenticated) 28
Settings 29
Info screen 31
Technical specifications 32
Troubleshooting 35
2
Evo - All In One Player
Last updated: April 9, 2021 08:32. Revision #1455
evo all one player
This guide is designed to make installing and using this product as easy as possible. Information in this document has been carefully checked for
accuracy at the time of publishing; however, Cambridge Audio’s policy is one of continuous improvement, therefore design and specifications are
subject to change without prior notice.
This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any
mechanical, electronic or other means, in any form, without prior written permission of the manufacturer. All trademarks and registered trademarks
are the property of their respective owners.
The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Audio Partnership
Plc is under license. Other trademarks and trade names are those of their respective owners.
Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries, used with permission.
aptX is a trademark of Qualcomm Technologies International, Ltd., registered in the United States and other countries, used with permission.
Qualcomm aptX is a product of Qualcomm Technologies International, Ltd.
StreamMagic is a trademark of Audio Partnership Plc and is registered in the European Community and other countries.
This product contains software licensed under version 2 of the GNU Public License and version 2.1 of the GNU Lesser Public License. The source
code for this software is available from: http://gpl.stream-magic.com/
This product includes technology owned by Microsoft Corporation and under a licence from Microsoft Licensing GP. Use or distribution of such
technology outside of this product is prohibited without a license from Microsoft Corporation and/or Microsoft Licensing, GP as applicable.
The Spotify software is subject to third party licenses found here: www.spotify.com/connect/third-party-licenses.
This product support AirPlay 2 and requires iOS 11.4 or later.
Apple and AirPlay are trademarks of Apple Inc., registered in the U.S. and other countries.
Use of the Works with Apple badge means that an accessory has been designed to work specifically with the technology identified in the badge and
has been certified by the developer to meet Apple performance standards.
Android, Google Play and the Chromecast built-in logo are trademarks of Google Inc.
TIDAL and TIDAL logo are registered trademark of Aspiro AB in the European Union and other countries.
MQA and the Sound Wave Device are registered trade marks of MQA Limited © 2016.
© Copyright Cambridge Audio Ltd
For upcoming news on future products, software updates and exclusive offers, make sure you register your product
at http://www.cambridgeaudio.com/register
Front panel controls
Last updated: April 7, 2021 11:30. Revision #1436
evo all one player / front panel controls
3
1. Display
2. Skip
3. Play/Pause
4. Speaker output
Press this button to choose a different speaker output from the menu. Use the source selector knob to select the speaker output between speaker
A, speaker B, speaker A+B, headphone and Bluetooth devices.
Note: Speaker A, speaker B and speaker A+B are available on the Evo 150 only.
5. Volume/Source selector
To change the volume, rotate the front part.
To select a source, rotate the back part.
6. Info
During playback, pressing this button will cycle through ‘Now Playing’ screens. Press and hold to display the product info.
7. IR sensor
8. Standby/On
9. Headphones
For suitable headphones – connection will automatically mute the speaker output and the pre-out.
Evo display
Last updated: May 12, 2021 10:50. Revision #1574
evo all one player / evo display
4
1. Album/Source artwork
Displays the album artwork. Alternatively, if no albums are available this will display the source input icon.
2. Track title, artist and album
For Internet Radio, this will display the radio station name and the current playback.
3. Format info
Displays the streaming sample rate. For Internet Radio, this will display the bitrate the station is streaming.
4. Source input
Displays the currently selected source input.
5. Progress bar
When available, this will display the current track progression during playback.
6. Track time
When available, this will display the elapsed track time during playback.
7. Clock
8. Network connection
Displays the current network connection.
Wireless network
connection
Wireless connection with no internet
access Wired network connection Wired connection with no internet
access No network connection
9. Speaker output
Displays the currently selected speaker output.
10. Mute volume
Displays when the network streamer is muted.
11. Firmware update
This indicates when new firmware is available. Press the 'Info' button on the front panel or use the StreamMagic app to update the network
streamer's firmware.
5
12. MQA indicator
See the MQA section for more details.
13. Shuffle, Repeat and Repeat +1
Evo 150 rear panel connections
Last updated: April 26, 2021 09:15. Revision #1556
evo all one player / evo 150 rear panel connections
1. AC Power socket
2. Speaker terminals
B Speaker
For connecting a second pair of loudspeakers.
3. Evo CD
A dedicated connection from an Evo CD player.
4. Audio return channel (ARC)
A connection from a TV that supports ARC function.
5. USB Audio In
For connecting to PC/Mac computers.
Note: For Class 2 USB audio, Windows-based PCs require a Cambridge Audio USB driver to be installed before connection.
Ground Switch
Note: The ground switch position should be set to 1 as default. Use another position if a humming noise occurs.
Position 1 – Normal/default position. The main unit audio ground is lifted from chassis earth.
Position 2 – USB Audio ground is lifted from the main unit audio ground, which is also lifted from chassis earth. This may be useful to reduce hum
and noise that can occur with some USB Audio setups.
6
Position 3 – Main unit audio ground is connected directly to chassis ground and USB Audio ground. For some setups, this can reduce hum or noise
when certain TVs, Turntables, and other equipment are connected to the Evo unit.
6. USB Media
For connecting local media storage. Note that the USB ports are not intended for connection to Apple mobile devices; no functionality, charging or
otherwise is supported.
7. Ethernet
Use a wired connection for seamless playback of high-resolution 352.8kHz, 384kHz, and DSD 256.
8. Trigger Out
Use a link wire between the Evo 150 and a product that has a trigger input. This will synchronise the power state of both products when powering
the Evo 150 on/standby.
9. Trigger In/IR In
Trigger In – Use a link wire between a product that has a trigger output and the Evo 150. This will synchronise the power state of the Evo 150 with
the controlling unit
IR In – Receives modulated IR commands from an IR repeater or custom install systems.
10. RS232C
Custom install control – a full protocol is available for the Evo 150 on our website.
11. Digital Inputs (Coax and Optical)
Note: If a digital input is connected to a TV you can enable TV mode in the input settings of the StreamMagic app. This mode minimises lip-sync
delays on the audio path by bypassing MQA decoding and also reduces the chance of dropouts and glitches from some TVs.
12. Analogue Inputs (AUX/XLR)
13. MM Phono input
For connecting a turntable that uses a moving magnet cartridge.
Ground
If your turntable has a separate grounding lead, then connect here.
14. Sub-Out
15. Pre-Out
Evo 75 rear panel connections
Last updated: April 28, 2021 09:51. Revision #1555
evo all one player / evo 75 rear panel connections
7
1. AC Power socket
2. Speaker terminals
3. Evo CD
A dedicated connection from an Evo CD player.
4. Audio return channel (ARC)
A connection from a TV that supports ARC function.
5. Ground Switch
Note: The ground switch position should be set to 1 as default. Use another position if a humming noise occurs.
Position 1 – Normal/default position. The main unit audio ground is lifted from chassis earth.
Position 2 – Main unit audio ground is connected directly to chassis earth. For some setups, this can reduce hum or noise when certain TVs,
Turntables, and other equipment are connected to the Evo unit
6. USB Media
For connecting local media storage. Note that the USB ports are not intended for connection to Apple mobile devices; no functionality, charging or
otherwise is supported.
7. Ethernet
Use a wired connection for seamless playback of high-resolution 352.8kHz, 384kHz, and DSD 256.
8. IR In
Receives modulated IR commands from an IR repeater or custom install systems.
9. Digital Inputs (Coax and Optical)
Note: If a digital input is connected to a TV you can enable TV mode in the input settings of the StreamMagic app. This mode minimises lip-sync
delays on the audio path by bypassing MQA decoding and also reduces the chance of dropouts and glitches from some TVs.
10. Analogue Input
11. Sub-Out
8
12. Pre-Out
Remote control
Last updated: April 7, 2021 11:31. Revision #1437
evo all one player / remote control
1. Mute
2. Standby/On
3. Preset buttons
Press and hold to store the current source.
Note: Not available for media player queue, AirPlay or Chromecast sources.
4. Speaker output
Press to choose a different speaker output. Pressing this button will toggle the speaker output between speaker A, speaker B, speaker A+B,
headphone and Bluetooth devices.
5. Info
During playback, pressing this button will cycle through ‘Now Playing’ screens. Press and hold to display the product info.
6. Brightness
Pressing this button will alter the brightness of the display backlight between bright, dim and an option to switch off the backlight.
7. Eject CD (Evo CD only)
Press to eject the CD from the slot.
8. Stop (Evo CD only)
9. Play/Pause/Skip
10. Source selection
9
11. Volume
Replaceable side panel
Last updated: April 7, 2021 11:29. Revision #1431
evo all one player / replaceable side panel
When installing new magnetic side panels, please ensure that the groove cuts are aligned with the direction of the front panel. Insert from the rear
by holding the rear of the panel.
Important note: The magnets can snap hard and pinch your fingers if not done correctly.
Getting connected
Last updated: April 21, 2021 02:06. Revision #1554
evo all one player / getting connected
Basic connections
The diagram below shows the basic connection of your Evo to a pair of loudspeakers.
10
Speaker B connections (Evo 150 only)
The diagram below shows the connection for a second pair of loudspeakers. Pressing the speaker output icon will scroll through the selection of
speakers, speaker A, speaker B, and speaker A and B together.
Preamp Out connections
The Preamp Out sockets are for connecting to a power amplifier or active subwoofer.
Tabla de contenidos
Otros manuales de Placa giratoria de Cambridge Audio
Cambridge Audio
Cambridge Audio ALVA TT Manual de usuario
Cambridge Audio
Cambridge Audio Alva TT v2 Manual de usuario
Cambridge Audio
Cambridge Audio ALVA TT Manual de usuario
Cambridge Audio
Cambridge Audio Alva Duo Manual de usuario
Cambridge Audio
Cambridge Audio Alva TT v2 Manual de usuario
Cambridge Audio
Cambridge Audio ALVA TT Manual de usuario
Cambridge Audio
Cambridge Audio Evo 75 Manual de usuario
Cambridge Audio
Cambridge Audio TT50 Manual de usuario
Cambridge Audio
Cambridge Audio Alva ST Manual de usuario
