Cabletron Systems 9C214-1 Manual de usuario
SmartSwitch 9000
9C214-1 AC Power Supply
Installation Guide
9031156-02
i
Notice
Notice
Cabletron Systems reserves the right to make changes in specifications and other information
contained in this document without prior notice. The reader should in all cases consult Cabletron
Systems to determine whether any such changes have been made.
The hardware, firmware, or software described in this manual is subject to change without notice.
IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL, INDIRECT,
SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED
TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION
CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN ADVISED OF, KNOWN, OR
SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES.
© Copyright March 1998 by:
Cabletron Systems, Inc.
35 Industrial Way
Rochester, NH 03867-5005
All Rights Reserved
Printed in the United States of America
Order Number: 9031156-02
LANVIEW
is a registered trademark, and
SmartSwitch
is a trademark of Cabletron Systems, Inc.
CompuServe
is a registered trademark of CompuServe, Inc.
i960 microprocessor
is a registered trademark of Intel Corp.
Ethernet
is a trademark of Xerox Corporation.
Notice
ii
FCC Notice
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
NOTE:
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environment.
This equipment uses, generates, and can radiate radio frequency energy and if not installed in
accordance with the operator’s manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause interference in which case the user
will be required to correct the interference at his own expense.
WARNING:
Changes or modifications made to this device which are not expressly approved by the
party responsible for compliance could void the user’s authority to operate the equipment.
VCCI Notice
This is a Class A product based on the standard of the Voluntary Control Council for Interference by
Information Technology Equipment (VCCI). If this equipment is used in a domestic environment,
radio disturbance may arise. When such trouble occurs, the user may be required to take corrective
actions.
DOC Notice
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital
apparatus set out in the Radio Interference Regulations of the Canadian Department of
Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables
aux appareils numériques de la class Aprescrites dans le Règlement sur le brouillage radioélectrique
édicté par le ministère des Communications du Canada.
iii
Notice
DECLARATION OF CONFORMITY
ADDENDUM
Application of Council Directive(s):
89/336/EEC
73/23/EEC
Manufacturer’s Name:
Cabletron Systems, Inc.
Manufacturer’s Address:
35 Industrial Way
PO Box 5005
Rochester, NH 03867
European Representative Name:
Mr. J. Solari
European Representative Address:
Cabletron Systems Limited
Nexus House, Newbury Business Park
London Road, Newbury
Berkshire RG13 2PZ, England
Conformance to Directive(s)/Product Standards:
EC Directive 89/336/EEC
EC Directive 73/23/EEC
EN 55022
EN 50082-1
EN 60950
Equipment Type/Environment:
Networking Equipment, for use in a
Commercial or Light
Industrial Environment.
We the undersigned, hereby declare, under our sole responsibility, that the equipment packaged with
this notice conforms to the above directives.
Manufacturer Legal Representative in Europe
Mr. Ronald Fotino Mr. J. Solari
____________________________________________________ ______________________________________________________
Full Name Full Name
Principal Compliance Engineer Managing Director - E.M.E.A.
____________________________________________________ ______________________________________________________
Title Title
Rochester, NH, USA Newbury, Berkshire, England
____________________________________________________ ______________________________________________________
Location Location
Notice
iv
v
Contents
Chapter 1 Introduction
Using This Manual........................................................................................................1-1
The 9C214-1 Power Supply..........................................................................................1-1
Features ...................................................................................................................1-3
Power Distribution System..........................................................................................1-4
Related Manuals............................................................................................................1-5
Getting Help .................................................................................................................. 1-5
Chapter 2 Installing the 9C214-1 Power Supply
Installing the 9C214-1 Power Supply.........................................................................2-1
Powering Up the 9C214-1 Power Supply..................................................................2-3
Chapter 3 9C214-1 Power Supply Operation
Operating Functions..................................................................................................... 3-1
System Diagnostic Controller ..............................................................................3-1
Internal Temperature Sensor................................................................................3-2
Power Supply Cooling..........................................................................................3-2
LANVIEW LEDs....................................................................................................3-2
PWR Status LED.............................................................................................3-3
SMB Status LED..............................................................................................3-3
Power Supply Level Indicator LED.............................................................3-4
Chapter 4 Specifications
Safety...............................................................................................................................4-1
Service............................................................................................................................. 4-1
Physical...........................................................................................................................4-2
Environmental...............................................................................................................4-2
Universal AC Input.......................................................................................................4-2
Input Voltage ................................................................................................................. 4-2
Fusing .............................................................................................................................4-2
AC Input Connection ...................................................................................................4-3
Output Voltage .............................................................................................................. 4-3
Contents
vi
1-1
Chapter 1
Introduction
UsingThis Manual
Read through this manual to become familiar with its contents and to gain an
understanding of the features and capabilities of the 9C214-1 power supply prior
to installing and operating it.
Chapter 1,
Introduction
, provides a brief description of the 9C214-1 power
supply and its features. This chapter also includes a list of related manuals and
information on getting help.
Chapter 2,
Installing the 9C214-1 Power Supply
, contains detailed steps for
unpacking, installing, and powering up the 9C214-1 power supply.
Chapter 3,
9C214-1 Power Supply Operation
, contains detailed information
regarding the power supply operation.
Chapter 4,
Specifications
, provides detailed specifications of the 9C214-1 power
supply.
The 9C214-1 Power Supply
The 9C214-1 power supply, shown in Figure 1-1, is a 1000 watt, triple output
supply that provides power to the SmartSwitch 9000 chassis. At least one power
supply must be installed; however, additional power supplies can be installed to
achieve redundancy. When two or more power supplies are installed, the system
uses a current sharing scheme where, under all load conditions, each supply
provides power equally.
Introduction
1-2
Figure 1-1. The 9C214-1 Power Supply
100-125v-12A
200-250v-6A
50-60 Hz
9C214-1
100%
50%
0%
Load
POWER SUPPLY MODULE
STATUS
P
W
R
S
N
B
Status LED
Power Supply
SMB
Status
LED
Power
Supply
Level
Indicator
LED
Power
Switch
AC
Power
Socket
Tabla de contenidos
Otros manuales de Fuente de alimentación de Cabletron Systems
Cabletron Systems
Cabletron Systems 9C214-3 Manual de usuario
Cabletron Systems
Cabletron Systems SmartSwitch 2200 Manual de usuario
Cabletron Systems
Cabletron Systems STS-PSU Manual de usuario
Cabletron Systems
Cabletron Systems 9C214-2 Manual de usuario
Cabletron Systems
Cabletron Systems SmartSTACK ELS100-S24TX2M Manual de usuario
Cabletron Systems
Cabletron Systems 9C500 Plus Manual de usuario
Cabletron Systems
Cabletron Systems MMAC-3 Instrucciones de instalación y funcionamiento
