Bunker Hill Security 61229 Instrucciones de montaje
Visit our website at: http://www.harborfreight.com
8-Channel
Surveillance DVR
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-800-444-3353 as soon as possible.
Copyright©2013 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Page 2 For technical questions, please call 1-800-444-3353. Item 61229
Table of Contents
Safety......................................................... 3
Specifications ........................................... 5
Set up - Before Use .................................. 6
Quick Start Guide Flow Charts................ 8
DVR Equipment Connections................. 12
DVR Settings............................................ 15
Pop-Up Menu .......................................... 15
Main Menu............................................... 15
Main Menu Map....................................... 16
Main Settings........................................... 17
Recording Schedule ................................ 18
Motion Detection...................................... 19
Users ....................................................... 20
System Information.................................. 21
Display Settings....................................... 21
Display Output......................................... 22
Privacy Zones.......................................... 22
Recording Parameters............................. 23
Video Stream........................................... 23
Maintain Hard Drive................................. 24
Alerts........................................................ 24
DVR Operating Instructions .................... 2
Search Recordings.................................. 25
Backup Recordings ................................. 26
Format Drives.......................................... 27
PTZ Camera............................................ 27
Local Area Network Setup ...................... 28
Set up Remote Video Stream.................. 29
Set up Email Capability ........................... 29
Set up Smartphone Capability................. 29
Wide Area Network Setup....................... 30
Software ................................................... 31
DVR Client............................................... 31
Video Player ............................................ 32
MAC Record Player................................. 32
AVI Generator .......................................... 32
Smartphone............................................. 32
Maintenance Instructions ....................... 33
Troubleshooting ...................................... 34
Parts List .................................................. 35
Warranty ................................................... 36
WARNING SYMBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that follow
this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
IMPORTANT SAFETY INFORMATION
Read all safety warnings and instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
Page 3For technical questions, please call 1-800-444-3353.Item 61229
SAFETYOPERATIONNETWORK SETTINGS
Installation Precautions
1. Check federal, state and local surveillance laws
before installing video
and/or audio surveillance equipment.
2. Install only according to these instructions.
Improper installation can create hazards.
3. Do not overreach when installing this product.
Keep proper footing and balance at all times.
This enables better control in unexpected situations.
4. Wear ANSI-approved safety goggles
during installation.
5. Keep installation area clean and well lit.
6. Keep children and bystanders out of
the area during installation.
7. Do not install when tired or when under the
influence of alcohol, drugs or medication.
Use Precautions
1. This product is not a toy. Do not allow
children to play with or near this item.
2. Use as intended only.
3. Do not modify.
4. Maintain product labels and nameplates.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
Electrical Safety
1. Power Adapter plugs must match
the outlet. Never modify the plug in
any way. Unmodified plugs and matching
outlets will reduce risk of electric shock.
2. Do not expose DVR unit to rain or wet
conditions. Water entering the DVR will
increase the risk of electric shock.
3. Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil,
sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
Service
Have your DVR equipment serviced by a qualified repair person using only identical replacement parts.
This will ensure that the safety of the equipment is maintained.
Camera Safety Warnings
1. To prevent electric shock, do not attempt
to disassemble Camera. There are
no serviceable parts inside.
2. Use supplied Power Adapter only.
3. Do not expose the Power Adapter to rain
or wet conditions. Water entering the Power
Adapter will increase the risk of electric shock.
4. Do not abuse the Power Adapter cord. Never
use the cord for unplugging the plug from the
outlet. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
5. Handle Camera with care. Camera could be
damaged by improper handling or storage.
Page 4 For technical questions, please call 1-800-444-3353. Item 61229
SAFETY OPERATION NETWORKSETTINGS
DVR Safety Warnings
1. Maintain adequate airflow around DVR.
2. Use supplied Power Adapter only.
3. Do not expose the Power Adapter or DVR
console to rain or wet conditions. Water
entering the Power Adapter or DVR console
will increase the risk of electric shock.
4. Do not abuse the Power Adapter cord. Never
use the cord for unplugging the plug from the
outlet. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
5. Maintain labels and nameplates on the unit.
These carry important safety information. If
unreadable or missing, contact Harbor
Freight Tools for a replacement.
6. WARNING: Handling the cord on this product will
expose you to lead, a chemical known to the State
of California to cause cancer, and birth defects or
other reproductive harm. Wash hands after handling.
(California Health & Safety Code § 25249.5, et seq.)
7. The warnings, precautions, and instructions
discussed in this instruction manual cannot
cover all possible conditions and situations
that may occur. It must be understood by the
operator that common sense and caution are
factors which cannot be built into this product,
but must be supplied by the operator.
SAVE THESE INSTRUCTIONS.
Grounding
TO PREVENT ELECTRIC SHOCK AND DEATH FROM
INCORRECT GROUNDING WIRE CONNECTION:
Check with a qualified electrician if you are in doubt as to whether the outlet is properly
grounded. Do not modify the power cord plug provided with the tool. Never remove the
grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have
it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet installed by
a qualified electrician.
Figure A: Outlets for 2-Prong Plug
1. The included Power Adapters do
not require grounding.
2. The Power Adapters may be used in
either of the 120 volt outlets shown in the
preceding illustration. (See Figure A.)
Extension Cords
Note: Do not use an extension cord with the Power Adapters.
Symbology
Double Insulated
Canadian Standards Association
Underwriters Laboratories, Inc.
VVolts
~Alternating Current
AAmperes
Page 5For technical questions, please call 1-800-444-3353.Item 61229
SAFETYOPERATIONNETWORK SETTINGS
Specifications
DVR
Hard Drive 500 GB
Video Standard NTSC / PAL
Video Codec H.264
Video I/O Input: 8 BNC
Output: 2 BNC / 1 VGA
Audio Codec G.711
Audio I/O Input: 1 RCA
Output: 1 RCA
Recording Resolution
CIF: 352 x 240;
HD1: 704 x 240;
D1: 704 x 480
Frame Rate Up to 30 fps each channel
Recording Mode Manual / Schedule / Motion Detection / Remote
Motion Detection Selectable Area and Sensitivity Detection
PTZ Interface RS485 - Supports Pelco-D/P camera (sold separately)
Network Interface RJ-45 10m/100m Ethernet Interface
USB Interface USB 2.0
DVR Input Rating 12VDC / 2A
Operating Temperature 32º - 131ºF
Cameras
Lens Types 2 Cameras with fixed 6 mm lenses
2 Cameras with fixed 3.6 mm lenses
Horizontal Resolution 400 TVL
Effective Pixels 648H x 488V
Night Vision Type Infrared LEDs with Low Light Sensor
Image Type Daylight: Color
Infrared: Black & White
Infrared Wavelength 850nm
Infrared Distance 30 ft. (indoors)
Ingress Protection Rating IP65 - Protected from low pressure water jets
Video Connector BNC
Camera Input Rating 12VDC / 500 mA
Cable Length 60 ft.
Operating Temperature 14° - 122°F
Page 6 For technical questions, please call 1-800-444-3353. Item 61229
SAFETY OPERATION NETWORKSETTINGS
Set up - Before Use:
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
Components and Controls
DVR Front Panel
9 10
1
18
1711 12 13 14 15 16 19
234 5 6 7 8
Figure B
1 Green Power Indicator
2 Remote Control IR Receiver
3 Red Hard Disk Drive Activity Indicator
4 Search Recordings
5 Mute
6 Previous Channel
7 Next Channel
8 Toggle 4 and 9 Screen Displays
9 Menu Up / PTZ Up
10 PTZ Control Mode
11 Rewind / Activate Controls
12 Pause
13 Play
14 Fast Forward
15 Stop
16 Start Manual Recording
17 Open Menu / Escape / PTZ Left
18 Menu Down / PTZ Down
19 Conrm Selection / Edit Selected Setting / PTZ
Right
Note: Controls for PTZ mode are italicized.
DVR Back Panel
1
5
23 4
67 8 9
Figure C
1 BNC Video Input 8
2RCA Audio Input 1
3 RJ45 LAN Ethernet Port 1
4 12VDC Power Input 1
5 BNC Video Output 2
6RCA Audio Output 1
7 VGA Port 1
8 USB 2.0 Port 2
9 RS485 PTZ Connector 1
Page 7For technical questions, please call 1-800-444-3353.Item 61229
SAFETYOPERATIONNETWORK SETTINGS
DVR Accessories
Power Adapter
Power
(to DVR)
BNC to RCA Cable
BNC
(to DVR)
RCA (to
Monitor)
Mouse
Note:
2 AAA
batteries
included.
Remote
Remote Control Functions
1 - 8 Select Channel
ALL Toggle 4 and 9 Screen Displays
MENU Open Menu
MUTE Mute
SUBMENU Open Pop-Up Menu
▲Menu Up
▼Menu Down
◄Menu Left
►Menu Right
SEL Confirm Selected Operation
◄◄ Rewind
►Play / Search Records
►► Fast Forward
●Record
ll Pause
■Stop
Figure D
Camera and Accessories
Video
(from Camera)
Video
(to DVR)
Power
(to Camera)
Power
(from Splitter)
Cable - 60 ft.
Screws
Anchors
Mounting Hardware
Power
(from Cable)
Video
(to Cable)
Camera
Hood Lens
Power Adapter
Power
(to Splitter)
Power Splitter Power
(from Adapter)
Power
(to Cables)
Figure E
Page 8 For technical questions, please call 1-800-444-3353. Item 61229
SAFETY OPERATION NETWORKSETTINGS
Quick Start Guide Flow Charts
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual
including all text under subheadings therein before set up or use of this product.
Use the following flow charts to help make the cable connections, navigate the system and set up or change the unit
settings. Refer to the individual setup sections in this manual for detailed instructions on specific tasks.
INITIAL SETUP
Physical Connections 1
B1
B2
B3
B4
D2
D3
D4
B5
B1
B2
B1
B2
B1
B2
D5
D1
USB Port
Video Input
A
BC
BCD
A
Connect
Monitor
Connect
Cameras
Connect
Mouse
Power Input
Video Output
Connect
Power
D
BNC/RCA VGA
E
Mount
Cameras
Note: Monitor and
Surge Protector
sold separately.
See Page 12
Page 9For technical questions, please call 1-800-444-3353.Item 61229
SAFETYOPERATIONNETWORK SETTINGS
Set Date and Time
In DVR
Main Menu
Select System
Set Recording Mode
Motion Detection Settings
Manual
Which
Recording
mode?
2
4
Select
General
Set Date and
Time above
Set Date and
Time
Click Apply
then OK
Scheduled
In DVR
Main Menu
select Record
Press REC on
front of DVR -
red light will
flash
Select
Schedule
Select Channel
and Day of
Week
Select boxes
for Normal and
Motion
3
Repeat for all
Days and all
Channels
Click Apply
then OK
In DVR
Main Menu
Select Alarm
Select
Motion Select
Channel
Set Sensitivity
Level
Select Area
Select which
Channels
will record
Click Apply
then OK
Set Buzzer for
audible alarm
Set Date and
Time above
Set Recording
Mode above
See Main Settings on Page 17
See Recording Schedule on Page 18
See Motion Detection on Page 19
Page 10 For technical questions, please call 1-800-444-3353. Item 61229
SAFETY OPERATION NETWORKSETTINGS
Local Area Network (LAN) Setup
On PC, go to Start
Menu, click Run.
In DOS window
type “cmd”, click OK.
type “ipconfig”
press ENTER
STOP
Ensure you have a
Windows® PC with
Internet Explorer®
and a Router before
proceeding.
NO
Connect DVR to
Router via
Ethernet Cable
(Sold Separately)
From DVR Main Menu
select
Network > Network
Type = Static
Find the Router’s LAN
Write down:
1. Subnet Mask
2. Default Gateway
(Router’s IP Address)
In DVR Network > Network
change settings:
1. Client Port: 3000
2. HTTP Port: 3001
3. New IP Address
4. Subnet Mask you wrote down
5. Default Gateway you wrote down
6. DNS1 same as Gateway
Change last 3 digits
to a number between
200 and 255
Change last 3 digits
to a number between
100 and 255
Click Apply then OK
to save changes.
Click Exit, DVR will prompt
restart. Click OK.
After restart,
on DVR go to
Network > Network
to view settings.
Open Internet Explorer®.
In address bar, type in
DVR’s IP Address and HTTP Port:
http://xxx.xxx.xxx.xxx:3001
(where x = IP Address and 3001 = HTTP Port)
Press Enter.
Allow ActiveX Control to install.
You may need to adjust the settings in
Internet Explorer® by adding the http
address to Trusted Sites and modifying
ActiveX controls to allow installation.
After ActiveX Control installs,
Log in to DVR
with User Name and Password.
@
In DVR
Main Menu
Select System
Select
Users Set User Name
and Password
Click Apply
then OK
Do you have a
Windows® PC with
Internet Explorer®
and a Router?
YES
YES
NO
Create New IP
Address:
Are last 3 digits of
Default Gateway
between 0-99?
Ethernet
Connection
See Page 28
Otros manuales para 61229
1
Tabla de contenidos
Otros manuales de DVR de Bunker Hill Security
Bunker Hill Security
Bunker Hill Security 61624 Instrucciones de montaje
Bunker Hill Security
Bunker Hill Security 61229 Manual de usuario
Bunker Hill Security
Bunker Hill Security 62463 Manual de usuario
Bunker Hill Security
Bunker Hill Security 62463 Instrucciones de montaje
Bunker Hill Security
Bunker Hill Security 67139 Manual de instalación
