Bullseye Golf PRO Series Manual de usuario
PRO SERIES GOLF ENCLOSURE
INSTRUCTIONS
8’x10/9’x12’/9x14’/9’x15’/ By 5’Deep
Thank you for purchasing Bullseye Pro Series Golf Enclosure.
Please read the instructions carefully. If you have any questions, please email us at
MATERIAL LIST
Tubing Sizes for your Enclosure Sizes
8x10x5 9x12x5 9x14x5 9x15x5
2-68” 6-72” 2-68” 2-68”
8-60” 2-68” 12-60” 15-60”
6-48” 6-60” 6-48” 2-48”
2-46 1/2” 2-48” 2-46 1/2” 2-46 1/2”
2-46 1/2”
4 HOLE CORNER BRACKET WITH HARDWARE (4 BOLTS-4 NUTS)-14
4 HOLE SPLICER WITH HARDWARE (4 BOLTS-4 NUTS)-15
L BRACKET OPTIONAL FOR MIDDLE SUPPORT AND PROJECTOR MOUNT
DROP IN POST WITH PULLEY, WITH HARDWARE (2 WASHERS, NUT) 16
DROP IN POST SHORT, WITH HARDWARE (1 WASHER, 2 NUT) 12
DROP IN POST LONG, WITH HARDWARE (2 WASHERS, 2 NUT) 13
CORD LOCKS -4
1/4" ELECTRIC CORD 2 112" SECTIONS
2" BLACK VELCRO 2-36", 2-108", 1-144"
4" BALL BUNGEE 14, 11" BALL BUNGEE-2
ELASTIC CORD WITH HOOKS-2
1 1/2 PIPE INSULATION
To Cover the 2 Front Side Bars. Top Front Top, Top Side Bars,
Knoche Insulation is for the Corners
.
Match Tubing Sizes with the Enclosure Sizing
8’x10’x5’
2 A-B (1 1/2” TUBING WITH SPLICER ON OPPOSITE SIDES) 2- A-B 48”+48”
2 A-C (1 1/2” TUBING WITH SPLICER ON OPPOSITE SIDES) 2- A-C 48”+46 1/2”
3 E-E (1 1/2” TUBING SPLICERS ON 3 SIDES , SIDES AND TOP) 3-60”+60”
2 D 68" (1 1/2” TUBING) 2-68”
2 H 60" (1 1/2” TUBING) 2-60”
9'x12'x5'
2 A-B (1 1/2” TUBING WITH SPLICER ON OPPOSITE SIDES) 2-A-B 60”+48”
2 A-C (1 1/2” TUBING WITH SPLICER ON OPPOSITE SIDES) 2- A-C 60”+ 46 1/2”
3 E-E (1 1/2” TUBING SPLICERS ON 3 SIDES , SIDES AND TOP) 3- 72”+72”
2 D 68" (1 1/2” TUBING) 2-68”
2 H 60" (1 1/2” TUBING) 2-60”
9'x14'x5'
2 A-B (1 1/2” TUBING WITH SPLICER ON OPPOSITE SIDES) 2-A-B 60”+48”
2 A-C (1 1/2” TUBING WITH SPLICER ON OPPOSITE SIDES) 2- A-C 60”+ 46 ½
3 E-E (1 1/2” TUBING SPLICERS ON 3 SIDES , SIDES AND TOP) 3- 60”+ 60"+48"
2 D 68" (1 1/2” TUBING) 2-68”
2 H 60" (1 1/2” TUBING) 2-60”
9'x15'x5'
2 A-B (1 1/2” TUBING WITH SPLICER ON OPPOSITE SIDES) 2-A-B 60”+48”
2 A-C (1 1/2” TUBING WITH SPLICER ON OPPOSITE SIDES) 2- A-C 60”+ 46 1/2”
3 E-E (1 1/2” TUBING SPLICERS ON 3 SIDES , SIDES AND TOP) 3-60”+ 60”+ 60”
2 D 68" (1 1/2” TUBING) 2-68”
2 H 60" (1 1/2” TUBING) 2-60”
How to Join Your T-Slot Tubing
Take your Tubes and join them together using the 2 Flat Joiners. Put the bolt into the hole and
slightly install the nut. Then Slide into Tubing. You want to do this with all 4 nuts and bolts for
both sides of the Tubing. Once this is done slide them on to one of the tubing the line up the
second tubing then slide the first one to the middle of both tubing and tighten with an Allen
wrench. Do the same for the one on the opposite side.
How to Assembale the Sides.
Slide corner brackets on to vertical posts. Make sure the corners are flush with ends.
Make sure there is a Knoch on top corners. Then slide horizontal post on and tighten.
Make sure all posts are butted up against each other. Make sure bottom horizontal post
bracket is 6.5 inches in from the end.
How to Install the Velcro on Side Walls
Once both side walls are built Apply Velcro to the inside of the Aluminum Tubing.
On A-C-D
How to Install the Frame
Lift the sidewalls and connect with one of the E Tubes on the Floor. It would be best if someone
can help you. Do this for both side walls as Shown in the Picture below. Install the Corner
Bracket as shown Bottom Left Corner. The Sidewalls should now stand by themselves.
How to Mount the Top Tubes
Put 2 E Tubes on the Top of the Box and Connect this as well with Angle Connectors to the side
walls. Refer to the Pictures below. Put Velcro Tape on the 2 Top Tubes Front and Back. Make
sure Velcro is on the underside of the Tubing Facing the Ground.
Front View
Top View
INSTALL MIDDLE SUPPORT (OPTIONAL)
Take A-F 60" 1.5 X 1.5 AND 49.5 1.5 X 1.5 WITH SPLICER ON OPPOSITE
SIDES
Attached 2 corner brackets on end on opposite sides. Attach 47" section to top with
corner bracket. 47" sections sit on top of vertical sections. Slide 2 L brackets on opposite
sides to vertical section. The black slide-in Allen wrench bolt goes into the top arm. The
drop -in post with nut and washer attach to frame See drawing. Measure 7.5 ft from end
and put mark on bottom back section. Mount the rail with upper arm facing front of
frame. Attach with 2 corner brackets. On the top arm, slide the L-brackets in line with the
front and back sections. Lightly tighten. DO NOT INSTALL THESE TO THE
FRAME UNTIL AFTER THE TOP PANEL IS INSTALLED. Attach with drop in
posts and nut. There is a chance that the horizontal section is too low to attach due to
slight bending. You might have to have someone under it to push it up or use a C-clamp
to push the sections together. See pic below.
