Buckeye Smart Cart Manual de usuario
0900462 Rev: A (03/05) Page 1 of 4
INTRODUCTION
The Buckeye “Smart Cart” is the perfect dispensing system for cleaning large areas and where portability and mobility
are required. The “Smart Cart” system is an economical system designed for controlling cleaning costs. The “Smart
Cart” is ideal for foaming down large areas in a short amount of time. Chemicals are mixed accurately and
consistently using a dual pick-up in-line venturi valve with general and heavy cleaning modes. The “Smart Cart” is
set-up ready to use with the product Terminator. Cart comes with side mounting clips for easy and portable storage of
squeegee or scrubbing brush. Flow-Thru Brush Kit available separately.
PREPARATION
(1) Remove the “Smart Cart” from the shipping carton.
(2) Lift off top of product holding box and open the door.
(3) Attach the Action cap to a Terminator Action Pac.
(4) Invert the Terminator Action Pac so the product cap is on the bottom and slide into the Stainless Steel container
box. Make sure that the chemical pick-up line is not kinked or crimped. Close door and replace the cover.
(5) Connect to a water supply using the 10 ft water hose attached to the unit.
Water pressure should be 30 to 80 PSI. Water temperature should not exceed 140 degrees (F).
(6) If using a product other than Terminator, remove the (2) water valve t-handles and the cover of the dispenser.
Locate the (2) metering tips inserted into the barb fittings located on each side of the general and heavy cleaning
selector. Remove the chemical pick-up lines and replace the metering tips with those for the selected product as
noted in the metering tip chart below. Replace the chemical pick-up lines and secure with zip-ties. Replace
dispenser cover.
Product General Cleaning (tip color) Heavy Cleaning (tip color)
Gel Scrub N/A NO Tip
Liberate N/A Black
Convoy Peach Brown
Terminator Red Pink
IMPORTANT NOTES
•ONLY USE A HOSE AND SPRAY NOZZLE SUPPLIED BY BUCKEYE.
•DO NOT ADJUST THE KNOB ON THE SPRAY NOZZLE FROM THE FULL SPRAY POSITION.
•DO NOT OPERATE MORE THAN ONE PRODUCT VALVE AT A TIME, AS PRODUCT DILUTION RATES WILL
NOT BE ACCURATE.
•UNIT SUPPLIED WITHOUT A BACKFLOW PREVENTION DEVICE. TO PREVENT POSSIBLE CHEMICAL
BACKUP INTO THE WATER SUPPLY, COMPLY WITH ALL LOCAL PLUMBING CODES AND INSTALL AN
APPROPRIATE BACKFLOW PREVENTION DEVICE.
CAUTION: Wear protective clothing and eyewear when dispensing chemicals or
other materials. Observe safety handling instructions (MSDS) for chemicals.
CAUTION: When installing any equipment, ensure that all national and local
safety, electrical, and plumbing codes are met.
SMART CART
INSTRUCTION MANUAL
Page 2 of 4 0900462 Rev: A (03/05)
OPERATION
(1) Select either general or heavy cleaning by turning the selector valve on the unit.
(2) Turn the “Foam” valve to the on position and depress the spray nozzle handle. The selected product and water
mixture will de dispensed.
(3) To “Rinse,” turn off the “Foam” valve, turn on the “Rinse” valve, and depress the spray nozzle handle. It may take
a few seconds to clear the hose of product before only water is being dispensed. For higher volume rinse remove
the foam wand via the quick disconnect at the end of the spray nozzle.
(4) Do not have both the Foam and Rinse valves on at the same time.
ALTERNATE METERING TIP RATIOS
NOTE: The chart below is based upon the chemical viscosity of water (CPS = 1.0) and should only be used as a
guide — the values were derived using water as the working fluid and 40 PSI dynamic input pressure. Actual ratios
and flow rates may vary due to product viscosity, flow pressure, and tubing distance(s).
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE REMEDY
No output (1) Water supply is off
(2) Product valve is off (1) Turn water supply on
(2) Turn appropriate valve on
Product is not drawn from container (1) Clogged metering tip
(2) Water inlet blocked
(3) Low water pressure
(4) No product in container
(5) Supply tube is loose
(6) Hose nozzle not fully open
(1) Clean or replace
(2) Check/clean screen
(3) Must be 30 PSI minimum
(4) Use new container
(5) Tighten or replace tie wrap
(6) Fully squeeze nozzle to open all
the way
Too much, or too little product is
drawn Incorrect metering tip Choose the next closest ratio from
chart and verify results — repeat this
step as necessary until the correct tip
is chosen
No water (or very low flow) (1) Obstruction at inlet screen area
(2) Low water pressure
(3) Scaled or clogged fittings
(1) Clean obstruction/replace screen
(2) Use a more suitable source
(3) Clean scaling or free obstructions
Supply container fills with water Checkvalve clogged Clean or replace checkvalve
TIP COLOR RATIO OZ/GAL
No Tip 15 :1 8.0
White 15 :1 8.0
Yellow 15 :1 7.8
Pink 16 :1 7.4
Dk Green 19 :1 6.4
Black 24 :1 5.1
Brown 30 :1 4.2
Gray 37 :1 3.4
Blue 43 :1 2.9
Red 54 :1 2.3
Peach 88 :1 1.4
Lt Blue 147 :1 0.9
Purple 210 :1 0.6
Lt Green 307 :1 0.4
Orange 570 :1 0.2
Lt Brown 0.1999 :1
0900462 Rev: A (03/05) Page 3 of 4
Page 4 of 4 0900462 Rev: A (03/05)
WARRANTY
The Smart Cart is warranted against defects in material and workmanship for a period of ONE YEAR from the time of
shipment from the Buckeye warehouse. Warranty applies only to the replacement or repair of such parts when
returned to Buckeye International, Inc. with a Returned Goods Authorization and is found to be defective upon
inspection. Rubber and synthetic rubber parts such as “O” rings, diaphragms, tubing and hoses are considered
expendable and are not covered under warranty. Warranty does not cover liability resulting from performance of this
equipment nor the labor to replace the unit. Product abuse or misuse voids warranty.
Tabla de contenidos
