Brother Quattro 6000D Manual de usuario

Upgrade KIT

III

Operation Manual

ENGLISH

CONTENTS

BEFORE YOU START................................................................................................................. 2

NEW FEATURES ........................................................................................................................ 2

EMBROIDERING WITH THE BORDER EMBROIDERY FRAME (30 cm × 10 cm (approx. 11-3/4

inches × 4 inches))..................................................................................................................... 3

About the Border Embroidery Frame...................................................................................... 3

Sample Projects Using the Border Embroidery Frame ............................................................ 3

Selecting a Pattern ................................................................................................................. 4

Hooping the Fabric in the Border Embroidery Frame ............................................................. 6

Attaching the Border Embroidery Frame to the Embroidery Unit............................................ 7

Embroidering the First Pattern................................................................................................ 8

Removing the Border Embroidery Frame ............................................................................... 9

Embroidering the Next Pattern............................................................................................... 9

USING THE CAMERA TO CONNECT PATTERNS ................................................................... 12

Connecting Patterns.............................................................................................................12

Preparation (Camera Needle Position Setting)...................................................................... 13

Practice (Connecting Three Patterns) ................................................................................... 14

CHANGING THE POSITION OF A STICKER ........................................................................... 22

CONNECTING ROTATED PATTERNS..................................................................................... 27

CHANGING THE REFERENCE EDGE AND REFERENCE POINT FOR CONNECTING THE NEXT

PATTERN AFTER A PATTERN HAS BEEN EMBROIDERED ...................................................... 29

SLIDING THE POSITION OF THE PATTERN TO BE CONNECTED ......................................... 32

Connecting Patterns to be Joined Along an Edge.................................................................. 33

TROUBLESHOOTING............................................................................................................. 36

Resume Feature................................................................................................................... 37

NEW FEATURES OF VERSION 2 (For NV1/NV6000D customer only) ..................................... 38

Displaying Patterns in The Embroidery Edit Screen Magnified By 200% .............................. 38

Specifying The Size of Pattern Thumbnails .......................................................................... 38

Saving a Camera Image or Settings Screen Image to USB Media.......................................... 39

Displaying The Grid ............................................................................................................ 40

Other New Features ............................................................................................................ 41

New Patterns for Version 2 .................................................................................................. 44

COLOR CHANGE TABLE FOR THE EMBROIDERY PATTERNS ON THE CD-ROM ................. 45

BEFORE YOU START

It is important to perform the upgrade according to the procedure described in the Installation Guide. The machine

can then be used as described in the Operation Manual. The border embroidery frame (30 cm × 10 cm (approx. 11-

3/4 inches × 4 inches)) will show on the LCD screen of the machine and the frame will be recognized when

attached to the embroidery frame holder. New machine features and benefits are described in this guide.

NEW FEATURES

• A border embroidery frame (30 cm × 10 cm (approx. 11-3/4 inches × 4 inches)) is included, allowing the

fabric to easily be rehooped when embroidering repeated patterns.

• Instead of using a thread mark, the built-in camera can be used to connect embroidery patterns. (Embroidery

Edit)

• Ten embroidery designs created to show the convenience and potential of the border embroidery frame are

available on the included CD. To view a list of the patterns, refer to page 45.

EMBROIDERING WITH THE BORDER EMBROIDERY

FRAME (30 cm × 10 cm (approx. 11-3/4 inches × 4

inches))

About the Border Embroidery Frame

Since the fabric can easily be repositioned and

rehooped when the border embroidery frame is used,

this frame is useful for embroidering repeated

patterns while sliding the fabric. An added feature of

this frame is that the pressure applied by the upper

and lower frames will not leave an indentation in the

fabric. An area of 30 cm × 10 cm (approx. 11-3/4

inches × 4 inches) can be embroidered.

Sample Projects Using the Border

Embroidery Frame

We recommend using the border embroidery frame

when repeated patterns are embroidered at the edges of

items such as curtains, chair covers, bed covers,

tablecloths and blankets.

CAUTION

• Do not leave the border embroidery frame within

the reach of children, otherwise injuries may result.

Note

• When the border embroidery frame is not being

used, unlock it before storing it.

• Due to its construction, the border embroidery frame

does not hold fabric as tightly as other frames. Since

fabric shrinkage may occur, depending on the fabric

and pattern used, be sure to sew trial embroidery on

a piece of scrap fabric before sewing your project.

Selecting a Pattern

aPress .

bOn page 6/8 for the embroidery frame display

settings, select one of the embroidery frame

displays for the border embroidery frame (30

cm × 10 cm (approx. 11-3/4 inches × 4

inches)). Press to return to the previous

screen.

* Of the 16 settings available, there are 2 for border

embroidery frames (30 cm × 10 cm (approx. 11-3/4 inches

× 4 inches)).

aBorder embroidery frame embroidering area

(30 cm × 10 cm (approx. 11-3/4 inches × 4 inches))

bCenter mark

cPress / and select a pattern, and

then press .

dUse the border function to repeat the pattern.

Memo

• For details for the border function, refer to

“Designing Repeated Patterns” in chapter 6 of the

Operation Manual for the sewing machine.

eIf necessary, assign thread marks. Since the

pattern will be repeatedly embroidered from

the top to the bottom, add the thread mark to

the lower center of the bottom pattern. When

you are finished, press .

→Touch and , or and to highlight

the design for inserting thread marks.

Note

• Do not add thread marks to character patterns.

• Add thread marks to patterns that do not have a

point of alignment, such as rotated patterns or

patterns that are spaced apart. Patterns that can be

aligned visually can be embroidered cleanly without

the thread mark.

Memo

• Select the location where the thread mark is to be

added according to the direction that the embroidery

is repeated.

If the design direction is rotated, use the following

suggestions.

aFirst Pattern

bSecond Pattern

cThread mark

fPress .

Hooping the Fabric in the Border

Embroidery Frame

aWith a chalk pen, mark the fabric with a line

drawn down the center of the area to be

embroidered.

aPattern

bCenter mark (line)

bAffix stabilizer material to the fabric to be

embroidered.

cIf the upper frame is locked down against the

lower frame, press the left and right lock

release buttons to unlock the upper frame.

aLock release buttons

dLay the fabric between the upper and lower

frames.

Note

• When embroidering the edges of the fabric, affix

stabilizer material larger than the fabric, and then

firmly secure the fabric and excess part of the

stabilizer material within the border embroidery

frame (in the same way as when the normal

embroidery frame is used). Otherwise, misaligned

patterns may result.

aFabric

bStabilizer

ePlace the embroidery sheet in the upper

frame, align the guide line on the embroidery

sheet with the center mark (line) on the

fabric, and then press down on the left and

right locking levers until they click into place.

aLocking levers

fRemove the embroidery sheet, and then

gently pull the four sides of the fabric to

remove any excess slack. Be careful so that

fabric is not stretched out of shape. Finally,

check that the fabric is firmly within the

hoop.

Attaching the Border Embroidery

Frame to the Embroidery Unit

aMake sure that the needle and presser foot

have been raised. If the needle has not been

raised, press the “Needle Position” button to

raise it. If the presser foot has not been raised,

press the “Presser Foot Lifter” button to raise

it.

bMake sure that the embroidery unit carriage

has moved to its initial position.

cAlign the guide on the border embroidery

frame with the right edge of the embroidery

frame holder.

aEmbroidery frame holder

bGuide on border embroidery frame

Memo

• The fabric can also be positioned in the border

embroidery frame by aligning the edge of the fabric

with the inner markings on the upper frame.

Note

• If there is excess fabric after the center of the

embroidering area is aligned with the center of the

border embroidery frame, fold over the excess

fabric, place it on top of the upper frame, and then

press down on the levers. Be careful that the folded

excess fabric is not caught in the embroidering area.

CAUTION

• After firmly hooping the fabric in the border

embroidery frame, attach the frame to the

embroidery unit. Otherwise, the needle may break

and cause injuries.

• Before attaching the border embroidery frame to

the embroidery unit, make sure that the needle and

presser foot have been raised. Otherwise, the

needle may break and cause injuries.

Note

• Before attaching the border embroidery frame, wind

the bobbin with thread and install it.

dSlide the border embroidery frame into the

embroidery frame holder, making sure to

align the border embroidery frame's arrow

mark (U) with the embroidery frame holder's

arrow mark (U).

aArrow marks

eLower the frame-securing lever so that it is

level with the border embroidery frame to

secure the border embroidery frame to the

embroidery frame holder.

aFrame-securing lever

Embroidering the First Pattern

aTo check the embroidering area, press .

bThread the machine, and then start

embroidering.

→When embroidering is finished, the thread mark is

sewn with the last thread color.

CAUTION

• If the frame-securing lever is not lowered, the

pattern may not embroider correctly or the presser

foot may strike the border embroidery frame and

cause injuries.

Note

• When the border embroidery frame is used, the

embroidering time may vary slightly than the time

that appears in the screen, depending on the type of

fabric and pattern that is used.

CAUTION

• Do not touch the border embroidery frame while

embroidering.

Removing the Border Embroidery

Frame

aRaise the frame-securing lever and pull the

border embroidery frame toward you.

Embroidering the Next Pattern

aPress both lock release buttons and slide the

fabric to align the embroidering area of the

next pattern, and rehoop the fabric in the

border embroidery frame.

aPattern embroidered first

bPosition of pattern to be embroidered next

cEmbroidering area of embroidery sheet

bAttach the border embroidery frame to the

embroidery unit, and then press .

Note

• Before removing the border embroidery frame from

the embroidery unit, make sure that the embroidery

unit carriage has moved to its initial position.

CAUTION

• If the thread has become tangled and the

embroidery unit carriage does not move to its initial

position, even after the thread is cut, turn off the

machine, manually gently move the carriage, and

then remove the border embroidery frame.

• Only move the embroidery unit carriage when the

machine is turned off.

Note

• Adjust the position of the fabric so that the

embroidering area for the next pattern is within the

embroidering area of the embroidery sheet.

Otros manuales para Quattro 6000D

Tabla de contenidos

Otros manuales de Máquina de coser de Brother

Brother

Brother 882-W07 Guía de inicio rápido

Brother

Brother T-8420C Manual de usuario

Brother

Brother PE-300S Manual de usuario

Brother

Brother PR-650 Guía de configuración

Brother

Brother LS-1217 Hoja de especificaciones

Brother

Brother BAS-605 Series Manual de usuario

Brother

Brother PS5234 Manual de usuario

Brother

Brother DB2-B737 MKII Manual de usuario

Brother

Brother 885-V94 Manual de usuario

Brother

Brother EF4-V51 Manual de usuario

Brother

Brother Innov-is NV55P Manual de usuario

Brother

Brother LT2-B841 Manual de usuario

Brother

Brother BAS-750KL Manual de usuario

Brother

Brother FA-V81A Manual de usuario

Brother

Brother BAS-343E Manual de usuario

Brother

Brother BM-2000 Manual de usuario

Brother

Brother BP2100 Guía de configuración

Brother

Brother NX-200 Manual de usuario

Brother

Brother 888-P20 Manual de usuario

Brother

Brother 888X74 Series Manual de usuario

Brother

Brother Z-8550A Manual de usuario

Brother

Brother LZ2-B850 Manual de usuario

Brother

Brother SC9500 Guía de configuración

Brother

Brother BE-1201-PC Manual de lista de piezas

Manuales populares de Máquina de coser de otras marcas

Riccar

Riccar RL634DE Manual de usuario

Singer

Singer 2517 Manual de usuario

Pfaff

Pfaff 3307-1 SERIES Manual de usuario

Janome

Janome Quilt Maker Pro 18 VERSA Manual de usuario

Siruba

Siruba C007JP Manual de usuario

Husqvarna Viking

Husqvarna Viking Designer SE Manual de usuario

Singer

Singer 148-5 Manual de usuario

IKEA

IKEA SY Manual de usuario

Pfaff

Pfaff 571 Manual de usuario

Singer

Singer 15-91 Manual de usuario

Pegasus

Pegasus WT100 Series Manual de usuario

Reliable

Reliable 7100DB Manual de usuario

Pfaff

Pfaff 937 Manual de usuario

Singer

Singer 6038 Manual de usuario

Singer

Singer 413K Manual de usuario

Pfaff

Pfaff 1471 E1 Manual de usuario

Kenmore

Kenmore 16677 - Serger Sewing Machine Manual de usuario

HIGHLEAD

HIGHLEAD GC2008-M Manual de usuario