Brookstone Handcrank Power Supply Manual de usuario
754219_INS_Emergency Power Supply V2
Size:5”Wx4.75”H_Output:100%_Prints:1/1,Blk
You’re never
left in the dark.
Handcrank Power Supply
ALWAYS PREPARED FOR ANY OUTAGE
Merrimack, New Hampshire USA 03054 • 800-846-3000 • Brookstone.com
1
TABLE OF CONTENTS
Warnings and Cautions ....................................................2
Location of Parts and Controls .............................................3
Location of Parts and Controls (Charging Panels). . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
LCD Icons (LCD Display)...................................................5
Charging the Emergency Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Setting the Time and Temperature Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Using the LED Flashlight ..................................................7
Using the AC Function.....................................................8
Using the USB Connection ................................................8
Using the 12V Power Outlet ...............................................9
Using the Jump Starter....................................................9
Care and Maintenance....................................................10
Power Information when Fully Charged. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Specifications............................................................12
Warranty.................................................................13
2
Do not try to remove the internal battery or try to repair this product. This product has an
internal inverter and jump-starter technology that raises the voltage and output to a much
higher level than the internal battery. Opening the product can cause serious injuries!
IMPORTANT This unit contains a lead acid battery that should be delivered
to a battery collection point for recycling at the end of its life.
• Read the instructions carefully before usage, and follow all the instructions.
• Connect the cables correctly and only use normal sockets and USB connectors.
Do not put any other object in the USB or AC output port.
• High voltage circuitry is used inside the body. Do not open the case at any time.
• Do not block the vent. Keep the AC socket dry to prevent electric shock.
• Do not operate in temperatures less than 14 degrees Fahrenheit.
• The unit should not be placed on sand or dirt as the fan for the heat reduction
at the bottom may blow or suck debris into the unit.
• To prevent the leakage of electrolyte in the lead acid battery, the unit should
be set upright on the ground.
• Always use the crank consistently. Rotating too slowly may reduce the current
and prolong charging time required.
• Rotating too fast will damage the internal gear.
• Do not place the device in very high temperatures or very humid environments.
• Use only the charging cables included.
• Charge the product at least once per month to prolong the life of the internal battery.
• Do not shine LED lights directly in eyes under any circumstances.
• When the unit is used for the first time, or not used for over 120 days, the internal
battery needs to be powered by DC charging for 14 hours.
WARNING!
HIGH VOLTAGE!
754219_INS_Emergency Power Supply V2
Size:5”Wx4.75”H_Output:100%_Prints:1/1,Blk
LOCATION OF PARTS AND CONTROLS
1. On/Off LED Light Switch
2. LED Light
3. LCD Display
4. Control Panel
5. Charging Panel 1 Door
6. Cable Access Door
7. Handle
8. Crank
9. Charging Panel 2 Door
10. AC Adapter (not shown)
11. 12V Car Adapter (not shown)
4
9
8
7
6
5
3
2
1
3
4
754219_INS_Emergency Power Supply V2
Size:5”Wx4.75”H_Output:100%_Prints:1/1,Blk
LOCATION OF PARTS AND CONTROLS (CHARGING PANELS)
1. Charging Panel 1 Cover
2. DC In
3. Solar In
4. 120V AC Power Outlet
5. 5V USB Outlet
6. Charging Panel 2 Cover
7. 30A Fuse
8. 12V DC Power Outlet
1 2 3
54
678
5
LCD ICONS (LCD DISPLAY)
5
1. AC/USB/Light Indicators
2. High Temperature Indicator
and Fan Icon
3. Inside/Outside Temperature
4. Charging Percentage
5. Set Button
6. USB Button
7. AC Button
8. Time
9. Overload Indicator
10. Voltage
Charging
Indicator
1
4
3
9
8
7
6
5
2
10
6
754219_INS_Emergency Power Supply V2
Size:5”Wx4.75”H_Output:100%_Prints:1/1,Blk
CHARGING THE EMERGENCY POWER SUPPLY
TURN THE CRANK
1. Pull the crank arm out of the holder and put it in its rotating position.
2. Rotate with a steady turning speed of 90-120 rotations per minute.
Please note: Turning the crank at a speed above 120 rotations per minute
may cause the gear to overheat and severe internal damage may occur.
3. During charging, the power level will blink on the LCD display.
4. Stop charging when the display shows a battery status of 100%.
CHARGING WITH AC ADAPTER (AC ADAPTER INCLUDED)
1. Connect the AC Adapter to an electrical outlet.
2. Connect the other end of the AC Adapter to DC-in of the unit.
3. During charging, the power level will blink on the LCD display.
4. Stop charging when the display shows a battery status of 100%.
CHARGING WITH 12V CAR ADAPTER (12V CAR ADAPTER INCLUDED)
1. Connect the 12V Car Adapter to the car’s cigarette lighter or power outlet.
2. Connect the other end of the 12V Adapter to DC-in of the unit.
3. During charging, the power level will blink on the LCD display.
4. Stop charging when the display shows a battery status of 100%.
IMPORTANT: During charging, the internal fan may operate to cool
off the inside temperature. This is a normal product function.
7
CHARGING BY SOLAR CELL (SOLAR CELL NOT INCLUDED)
1. To charge by solar cell, only use the solar input on the unit.
2. You may need an adapter tip to change the size of cable tip of a
solar cell to fit the unit.
SETTING THE TIME AND TEMPERATURE MODE
1. In Standby mode, press the SET button for 3 seconds.
2. The LCD display will show the time and the hour digit will blink.
3. Press the AC (+) or USB (-) buttons to adjust the hour.
4. Press SET to save the hour chosen. The minute digits will blink.
5. Press the AC (+) or USB (-) buttons to adjust the minute.
6. Press SET to save the minutes chosen. The 12/24 hour setting will blink.
7. Press the AC (+) or USB (-) buttons to choose between the 12 or 24 hour
display setting.
8. Press SET to save the 12/24 hour setting chosen. The C/F setting will blink.
9. Press the AC (+) or USB (-) buttons to choose between the C/F display setting.
Press SET to save.
USING THE LED FLASHLIGHT
1. Press the Light Switch on top of the unit to activate the LED flashlight.
2. Press again to activate the flashing red emergency light.
3. Press again to turn off.
8
754219_INS_Emergency Power Supply V2
Size:5”Wx4.75”H_Output:100%_Prints:1/1,Blk
USING THE AC FUNCTION
1. Press and hold the AC on/off button for three seconds to activate.
2. The AC power function will show on the LCD display. The power bank is now
ready to power any 120 Volt appliance with maximum power of 100 Watts.
3. Connect the plug of your 120 Volt device into the AC output.
Note: During use of the AC power function the internal inverter will get warm.
This is normal. The internal temperature is shown on the display. To cool down
the internal temperature, the integrated fan will automatically be activated
when required.
4. The wattage that is used by the connected AC device is shown in the display.
5. To deactivate the AC power function, disconnect your 120 Volt device and
press the AC on/off button for three seconds. The indication ‘AC OUTPUT’
will disappear from the display.
USING THE USB CONNECTION
1. Press and hold the USB on/off button for 3 seconds to activate the
USB function.
2. The USB power function will be displayed on the LCD display.
Connect the USB 2.0 connection of your mobile device to the USB
charging port from the unit.
3. The USB port can charge any mobile device with charging voltage of 5V
and output current of 1A.
4. To deactivate the USB output function, press and hold the USB button
for 3 seconds. The indicator USB OUTPUT will disappear from the display.
9
USING THE 12V POWER OUTLET
1. Open the Charging Panel 2 Cover.
2. Plug the 12V Car Adapter into the 12V Power Outlet.
3. Connect to device to be powered (up to 200W).
Replacing the Fuse: If the 12V Output isn’t operational, check the fuse and,
if fuse is blown (burned out), replace it with a 30A Fuse.
IMPORTANT: Only a 30A Fuse should be used.
USING THE JUMP STARTER
1. Open the CABLE DOOR.
2. Take out the RED and BLACK clamps.
3. Unscrew the BLACK nut from the negative terminal.
4. Connect the ring on the BLACK wire to the negative terminal.
5. Screw the BLACK nut back on the negative terminal to secure wire.
6. Unscrew the RED nut from the positive terminal.
7. Connect the ring on the RED wire to the positive terminal.
8. Screw the RED nut back on the positive terminal to secure wire.
9. Clamp the BLACK clamp to the negative pole of the car battery first followed
by the RED clamp to the positive pole of the car battery. This unit is able to
output a current of 200A.
WARNING! Fire or explosion may be caused because of a short circuit
or wrong connections of the poles.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
