brondell SMB-15 Manual de usuario
Owner's Manual
Side-Mounted
Attachable Bidet with
Adjustable Spray Wand
MODELS SMB15/SMB25
2
Table of Contents
SMB15 / SMB25 OWNER'S MANUAL
This manual contains important safety information. Before
operating your Side-Mounted Attachable Bidet with Adjustable
Spray Wand, please read this manual thoroughly and retain it
for future reference.
01
01
02
03
PRODUCT INFORMATION
Product Features
Product Dimensions
Product Parts
09
09
PRODUCT OPERATION
Using the Side-Mounted Attachable
Bidet with Adjustable Spray Wand
01 ENGLISH
15 SPANISH
30 FRENCH
GENERAL INFORMATION
PRODUCT INSTALLATION
PRODUCT OPERATION
TRANSLATIONS
TECHNICAL INFORMATION
04 PRODUCT INSTALLATION
04 Before Installation
05 Installation
06 Connecting the Hot Water Supply
07 Installing the Bidet Attachment
11 MAINTENANCE
12 PRODUCT SPECIFICATIONS
13 WARRANTY
14 CONTACT
1
Product Features
PRODUCT INFORMATION
SMB-15 Ambient Temperature Features
Durable Zinc Plated, All-Brass Construction
Swing-Action Spray Wand
Adjustable Water Pressure
Ceramic-Core Internal Valve
High-Quality Metal ⅞" T-Valve
Durable Braided Metal Cold Water Hose
No Electricity Or Batteries Required
Easy Installation And Adjustable Toilet Fit
All Accessories Included For Standard Installation
One-Year Warranty
SMB-25 Dual Temperature Features Only
Warm And Cool Water Bidet Washes
Adjustable Water Temperature
Durable High-Temperature Hot Water Flex Tubing
High-Quality Metal ⅜" T-Valve
One-Year Warranty
2
Product Dimensions
PRODUCT INFORMATION
SMB-25 Dual Temperature
SMB-15 Ambient Temperature
Ø 0.51 in
Ø 0.51 in
0.2 in thick
0.2 in thick
9.25 in
1.7 in
0.8 in
0.8 in
5.3 in
3.09 in
5.6 in
9.25 in
1.26 in
5.3 in
3.87 in
5.6 in
3
Product Parts
PRODUCT INFORMATION
1. Bidet Attachment
2. Mounting Guide Bolt
3. Small Rubber Washer
4. Metal Washer
5. Metal Nut
6. Cold Water T-Valve Connector
(⅞" x ⅞" x ⅜")
7. Large Rubber Washer
8. Cold Water Braided Metal Hose
(½” for Ambient or ⅜” for Hot & Cold
Version) Hose length = 15.75”
9. Mounting Washer
1. Hot Water ⅜" T-Valve with
¼" Pressure Connector
and Pressure Cap
2. Hot Water Tubing Pressure
Connector with Pressure Cap
3. ¼" Hot Water Flex Tubing,
Hose Length 78.75”
4. Small Rubber Washers (2)
5. Hot Water Supply Cap
1
1
2
2
3 4 5
3
7
5
6
8 9
4
SMB-25 Dual Temperature Only
4
IMPORTANT:
Please be advised that the provided cold water T-Valve
should be installed at the fill valve under the toilet tank,
and NOT at the cold water supply coming from the wall.
For SMB-25 Dual Temperature Model Only: Check
the size of the hot water supply connection (most
likely under the sink/wash basin). This should be a ⅜"
connection to properly fit and install enclosed T-valve.
Check Water Supply Line
Check the water supply line that connects the toilet tank fill
valve to the water shuto valve at the wall. If it is a rigid
pipe, you will need to purchase a flexible water supply
hose to replace it before installing the Side-Mounted
Attachable Bidet with Adjustable Spray Wand. The length
of the hose may vary, and the top connection size should
be ⅞" ballcock to connect to the T-valve that you will install
under the toilet tank. The bottom connection will vary
(most common are ⅜" and ½" female compression).
Before Installation
PRODUCT INSTALLATION
NOTE: The hot water T-Valve will be installed at the
hot water supply under your bathroom sink. If you
do not have access to the fill valve under the toilet
tank, visit us at www.brondell.com or contact us at
1-888-542-3355 for further assistance.
NOTE: If the connection is a ½" connection, you
will need to purchase the following reducing
adapter available online and at many plumbing
hardware stores: Reducing Adapter, ½" Female NPT
x ⅜" Male Compression
INCORRECT
Cold Water Supply
Fill Valve
CORRECT
5
Installation
PRODUCT INSTALLATION
Please read these instructions carefully before installing your
Side-Mounted Bidet. Failure to do so could result in flooding,
leaking or damage to the product.
1. Existing Toilet Seat Removal.
a. Lift hinge covers and use flathead or Phillips head
screwdriver to remove the mounting bolts. Alternatively, you
may need to loosen mounting bolts underneath the seat.
b. Remove the toilet seat and set the seat, mounting bolts
and hardware aside.
2. Turn O Water Supply Valve And Flush Toilet.
a. Turn water supply valve o to stop the flow of water.
b. Flush toilet and hold down handle to completely empty tank.
c. Disconnect water supply hose from toilet tank.
Do not disconnect from the water supply valve.
3. Connect Cold Water T-Valve To The Toilet Tank Fill Valve.
a. Install the ⅞" cold water T-valve with one or both of the
large rubber washers to the incoming water connection
on the bottom of your toilet tank.
b. Connect the cold water supply line coming from the wall
to the bottom of the T-valve.
4. Connect Bidet Hose To T-Valve.
Connect one end of the braided metal cold water bidet
hose to the remaining open side of the installed T-valve.
FOR AMBIENT TEMPERATURE MODEL, STOP HERE AND
PROCEED TO “INSTALLING THE BIDET ATTACHMENT” ON
PAGE 7. FOR DUAL TEMPERATURE MODEL, CONTINUE.
5. Install The Hot Water Supply Cap.
a. If you are only connecting the cold water supply, then you
must install the hot water supply cap (provided - see Page 3)
over the hot water connection on your bidet (see diagram).
b. After installing hot water cap, proceed to “Installing the
Bidet Attachment” on Page 7. If you wish to also connect
your hot water supply, proceed to "Connecting the Hot
Water Supply”.
Step 3a
Step 3b
Step 1b
Step 2c
Step 4
IMPORTANT: Failure to connect or cap the hot water
supply will result in leaking during use.
Step 5a
6
1. Connect The Hot Water Supply.
a. Locate the hot water supply line in your bathroom
under your sink/washbasin and turn the water supply
valve all the way o.
b. Drain the hot water line by turning the sink tap on the
hot setting until no more water comes out.
c. Disconnect hot water supply hose to sink from shut o
valve. You may have to use a ⅜" compatible wrench or
a similar tool (not supplied).
2. Install the Hot Water ⅜" T-Valve and the small rubber
washers as needed onto the hot water shut o valve
under the sink.
3. Reconnect hot water supply line to open end (top) of
T-valve.
4. If not already removed, unscrew the pressure cap
covering the pressure connector on the T-valve.
a. Slide the pressure cap over the open end of the of
hot water flex tubing with the inside threads facing
towards the open end.
b. Push the hot water flex tubing over the pressure
connector.
c. Slide the pressure cap down until the cap meets the
pressure connector. Screw the cap onto the T-valve
until secure and tight.
Connecting the Hot Water Supply
PRODUCT INSTALLATION
CAUTION: Do not over-tighten the pressure cap.
You will risk damaging the tubing.
IMPORTANT: Be sure to slide the hot water flex
tubing over the pressure connector until the tubing
slides past the “lip” of the pressure connector and
it cannot go any further.
NOTE: There may be some residual water in the
hose; use a small container or towel to catch any
residual water.
Step 4b
Step 4c
Step 1c
Steps 23
Step 4a
7
Installing the Bidet Attachment
PRODUCT INSTALLATION
1. Install mounting guide bolt into middle opening (1a) of
bidet attachment bracket. For one-piece or skirted toilets,
install mounting guide bolt into outside opening (1b) of
bidet attachment bracket.
2. Install Bidet Attachment On Toilet.
a. Place bidet attachment on the toilet, making sure to
insert mounting guide bolt into toilet bolt opening.
b. Secure bidet attachment to toilet bowl using small
rubber washer, metal washer, and metal nut.
c. Before tightening nut completely, use the nozzle
control handle to move spray wand to full extension.
Adjust bracket and control valve body until the spray
wand head is positioned in the center of the toilet
bowl, or in an alternative desired position. Gently
retract spray wand to ensure it sits just beneath toilet
bowl rim. Hand-tighten the metal nut until fully secured.
d. Place mounting washer over opposite toilet bolt
opening.
e. Replace the toilet seat on top of bidet attachment and
secure using original toilet seat hardware.
CAUTION: Avoid over-tightening, as damage may occur.
Step 1
(1a) (1b)
Step 2a
Step 2b
Step 2e
Step 2d
Step 2c
Control Valve Body
Spray Wand
Attachment Bracket
8
NOTE: If there is any leaking, check all rubber washers and make sure all water connections
are tight and secure. If necessary, you can use plumbers tape for any leaking connections.
TIP: If spray direction is o-center after installation or does not rest properly under toilet
bowl rim, loosen mounting nut, reposition the control valve body, and secure back in place.
Depending on your preferences or body composition, the perfect position may require
some readjustment.
3. Connect Bidet Hose To Bidet Attachment.
Connect the open end of bidet hose to the cold connection
behind the bidet attachment.
4. Connect Hot Water Tube To Bidet Attachment
(For SMB-25 Dual Temperature Model Only).
a. Take the hot water tubing pressure connector and
remove the pressure cap.
b. Slide the pressure cap over the open end of the of hot
water flex tubing with the inside threads facing towards
the open end.
c. Push the pressure connector into the open end of the
of hot water flex tubing with the washer facing out.
d. Hold the pressure connector up against the hot water
inlet on the bidet attachment. Slide the pressure cap
along the tubing and screw the cap onto the hot water
inlet until the pressure connector is secure.
5. Turn On Water Supply & Check For Leaks.
a. Open the main water supply valve slowly and check for
leaks.
b. Wait 5-10 minutes, check again, and if there are no
leaks, continue.
Installing the Bidet Attachment (contd.)
PRODUCT INSTALLATION
Step 4b
Step 4c
Step 4d
Step 3
IMPORTANT: Be sure to slide the hot water flex tubing
over the pressure connector until the tubing slides
past the “lip” of the pressure connector and it cannot
go any further.
NOTE: If you have already installed the hot water
supply cap over the hot water supply on your SMB-25
Dual Temperature model, skip to step 5.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Idiomas:
Otros manuales de Baño de brondell
brondell
brondell CL2200 Series Manual de usuario
brondell
brondell Swash T44 Manual de usuario
brondell
brondell SWASH BL97 Manual de usuario
brondell
brondell SE400 Manual de usuario
brondell
brondell LumaWarm Manual de usuario
brondell
brondell FreshSpa Comfort+ FSR-15 Manual de usuario
brondell
brondell Swash 300 Manual de usuario
brondell
brondell Swash Eco Thinline T66 Manual de usuario
brondell
brondell SWASH CSG15 Manual de usuario
brondell
brondell DS725 Series Manual de usuario
brondell
brondell Swash LES512 Manual de usuario
brondell
brondell Swash CL99 Manual de usuario
brondell
brondell Swash LS1800 Manual de usuario
brondell
brondell FreshSpa Comfort+ Manual de usuario
brondell
brondell Swash T22-EW Manual de usuario
brondell
brondell SWASH EM417 Manual de usuario
brondell
brondell FreshSpa Warm FSW 20 Manual de usuario
brondell
brondell Swash 900 Manual de usuario
brondell
brondell SWASH CL950 Series Manual de usuario
Manuales populares de Baño de otras marcas
Better Bathrooms
Better Bathrooms BUN/BeBa 27555/78725 Manual de usuario
American Standard
American Standard CONCEPT Cube TF-2704 Manual de usuario
BIOLAN
BIOLAN ECO Manual de lista de piezas
Thetford
Thetford C260 Series Manual de usuario
KELISS
KELISS T162A Series Manual de usuario
Kohler
Kohler K-22241K Instrucciones de montaje
