Brobo TNF 115 2 Series Manual de usuario
©
BROBO GROUP (AUST) PTY. LTD.
8 Fowler Rd, Dandenong South
Victoria 3175, AUSTRALIA.
☏
+ 61 3 9794 8751
📧
🖷 + 61 3 9794 8792 www.brobo.com.au
PRODUCT AND MAINTENANCE MANUAL
MANUAL NON-FERROUS CUTTING SAW
MODEL No. TNF 115 (SERIES 2)
___________________________________________________________________________________________
Precision Drilling Machines Tapping Machines Multi-Head Drills Tool Grinders
Tool Post Grinders Machine Vices Special Production Equipment
Accessories Riveting Machines Pedestal Grinders Metal Cutting Saws Linishers
YOUR BROBO DISTRIBUTOR IS:
A.C.N. 098 264 316
A.B.N. 42 098 264 316
Brobo Group
brobo.com.au
OPERATING MANUAL FOR BROBO GROUP
MANUAL NON-FERROUS CUTTING SAW TNF115
TECHNICAL SPECIFICATION
CHAPTER 1: Installation of the Machine
1.1 Unpacking & Handling the Machine
1.2 Parts Checklist
1.3 Minimum Requirements
1.4 Anchoring the Saw
1.5 Connection to Power Source
CHAPTER 2: Safety & Accident Prevention
2.1 Operation of the Machine
2.1.1. Noise Level
2.1.2. Power Supply
2.2 General Requirements
2.3 Advice for the Operator
2.4 Machine Safety Devices
2.4.1. Reference Standards
CHAPTER 3: Main Functions & Operation of the Machine
3.1.1. Cutting Head
3.1.2. Saw Safety Guard & Locking System
3.1.3. Saw Handle (with ‘Dead Man’ Trigger Switch)
3.1.4. Power Switch & Clamp Switch
3.1.5. Pneumatic Vice Clamp
3.2 Preparation for Operation
3.3 Operation Recommendations
CHAPTER 4: Drawings, Layouts, Assembly & Spare Parts
4.1.1 Main Dimensions
4.1.2 Assembly Drawings
4.1.3 Electrical Drawings
CHAPTER 5: Adjustments for the Saw Unit
5.1 Changing the Blade
5.2 Adjusting the Head Tilt
5.3 Cutting & Feeding Speeds
5.4 Lubricator Adjustment
5.4.1 Lubricating Oil Precautions – Health Hazard Information
CHAPTER 6: Maintenance & Selection of Consumables
6.1 Role of the Operator
6.2 Maintenance Requirements
6.3 General Maintenance of Functioning Components
CHAPTER 7: Appendix
i. Hazard/Risk Assessment
ii. Workplace Health & Safety Policy
Brobo Group
brobo.com.au
TECHNICAL SPECIFICATION
STANDARD FEATURES
Mitering 45° left, straight 90° & 45° right with rapid adjustment bumpers
45° Compound Mitering
Automatic Lubrication
Vertical & horizontal pneumatic clamping
400mm TCT blade
Two feed roller conveyors (3m long each).
3m Adjustable length stop
Trigger Switch (DMT) to activate the machine
BLADE SIZES
Blade Type: TCT Tungsten Carbide-Tipped
Blade RPM: r 3190 rpm
Blade RPM Max 4800 rpm
Blade Diameter D 400 mm
Bore d 30 mm
Tooth Width S 3.6mm
Body Thickness s 2.8mm
Tooth Geometry: TFZ N Triple chip tooth alternating with flat tooth
with negative hook angle
Number of Teeth z 120
CHARACTERISTICS:
Cutting of aluminium profiles & mouldings, plastic boards, brass
Suitable for angle cutting & cross cutting
MOTOR
Power: 1.5 kW
Rpm 2800 rpm
V Single Phase, 240V TNF115-240
3 Phase, 415V TNF115-415
PNEUMATIC
Air pressure 6-8 bar
Air Consumption 2.2 l/min
DIMENSIONAL SPECIFICATIONS
Base Dimensions 670 mm x 540 mm
Table Working Height 870 mm
Dimensions L x W x H 670 x 850 x 1700 mm
Packaged L x W x H 1140 x 1140 x 1700 mm
Roller Conveyor 300 x 30 x 20 mm
WEIGHT
m 167 Kg
Brobo Group
brobo.com.au
CUTTING RANGE CHART
90˚ 100 mm
45˚ 100 mm
90˚ 100 mm
45˚ 100 mm
90˚ 100 x 190 mm
45˚ 100 x 130 mm
Brobo Group
brobo.com.au
CHAPTER 1 - Installation of the Machine
1.1. Unpacking & Handling the Machine
Upon receiving the Brobo Group TNF115 Series 2, the machine should be standing upright & positioned centrally
on top of a wooden pallet. While the machine is situated on the pallet, position the forklift arms under the pallet
between the runners, keeping in mind that the machine is head heavy. Move the entire unit to an accessible area
as close as possible to the final location.
Carefully remove the wooden frame surrounding the saw unit (Figure 1). Once completed, proceed by elevating the
machine away from the pallet base using a sling harness wrapped around the cutting head of the saw. Ensure that
the floor is as level as possible before finally positioning the machine to the desired location.
FIGURE 1. Handling of Cutting Saw Unit
WARNING – HEAD HEAVY MACHINES
The metal sawing machines are heaviest where the saw heads are fitted & as such, care must
be taken while relocating or moving the machines.
Brobo Group
brobo.com.au
1.2. Parts Checklist
Along with the saw unit, check that the following accessories, packed "loose", are included as follows:
A. STANDARD ACCESSORIES
1) 1 Saw Blade
2) 1 Operating Manual
B. OPTIONAL ACCESSORIES
Part Number Description
9311270 Standard Adjustable Length Stop (600mm)
9501450
9501470
‘Brobo-Rule’ Series Manual Micro-Adjustment Length Stop
Available in 3.0m or 6.0m lengths
Field Kit includes rail, tape, micro-stop & extension arm.
9501210
Roller Conveyor
68 Kg Steel Rollers
3000mm x 305mm
150mm pitch
9504320 Adjustable Stand (610mm – 1016mm)
9540330 Stand V Type Roller
9540340 Stand Flat Roller
- Additional Blade(s) - Custom to Client Requirements
1.3. Minimum Requirements
For the machine to function correctly, the room in which the saw unit is to be installed must be in the vicinity of, &
satisfy the following conditions:
415/240V Power Supply
Ambient Temperature - From -10
C to +50
C.
Relative Humidity: Not more than 90%.
Lighting: More than 500 LUX.
WARNING – OPERATING VOLTAGE VARIATION
Each saw model has an inbuilt safety system to protect it against voltage variations. However,
for the machine to perform efficiently, ensure that the saw unit operates within
10% limits of the
recommended voltage of the motor.
Brobo Group
brobo.com.au
1.4. Anchoring the Saw
Prior to anchoring the saw unit, take into considerations the requirements mentioned in Section 1.3 & Section 2.2,
& other aspects regarding the usage of the machine such as accessibility to cut parts & safe access for the operator.
The base of the fabricated stand (if applicable), in which the saw head rests on, is anchored to the floor by 4 M12
bolts. For added stability, it is strongly recommended that the machine stand is fastened to the floor by using loxins
(not provided).
Required Working Area
It is recommended that A & B is more than 1.5m
Figure 2. Saw TNF115 S2 Length Stop with Conveyor
Brobo Group
brobo.com.au
1.5. Connection to Power Source
Before connecting the machine to the power supply, check that the socket is not connected in series with other
machines. This condition is critical for the ideal operation of the saw unit.
Single & Three Phase
a) Single phase machines are provided with three pins, 15 amps rated plugs & leads for connection to 240V,
50Hz power supply in Australia.
Figure 3.1 Connection 3 pins – 1 Phase
b) Three phase machines
Figure 3.2 Connection for “5-CORE” Wire System with Neutral – 3 Phase
c) Check the power supplied & motor specifications before plugging in the machine. Check the terminal
connection on dual voltage motor terminal box & connect it accordingly to the corresponding voltage supply.
d) If the dual motor is requested, the motor is always connected to the higher voltage, unless otherwise
specified prior to the order being placed.
Active = Brown VOLTAGE MAIN VOLTAGE
Neutral = Light Blue 240V/1 PH 240V
Earth = Green/Yellow
Brobo Group
brobo.com.au
CHAPTER 2 - Safety & Accident Prevention
The Brobo Group TNF115 Series 2 has been designed & manufactured in accordance with Australian Standards.
It is HIGHLY RECOMMENDED that the instructions & warnings contained in this chapter be carefully followed for
correct usage of the machine.
2.1. Operation of the Machine
The Brobo Group TNF115 Series 2 is specifically designed to cut non-ferrous metal cross sections with solid or
thin-walled profiles. Other types of material & machining are not compatible for use with the specifications of the
saw. This machine involves a high-speed blade rotation; therefore extreme caution is required when
operating the device.
The employer is responsible for instructing the personnel who, in turn, are obliged to inform the operator of any
accident risks, safety devices, noise emission & accident prevention regulations provided for by national &
international laws governing the use of the machine. The operator must be fully aware of the position &
functions of all the machine’s controls.
All those concerned must strictly adhere to ALL instructions, warnings, & accident prevention standards in
this manual.
The following definitions are those provided for by the EEC DIRECTIVE ON MACHINERY No. 98/37/CE:
Danger Zone - any zone in and/or around a machine in which the presence of a person constitutes a
risk for the safety & health of that person.
Person Exposed - any person finding him or herself, either completely or partly in a danger zone.
Operator - the person or persons are given the responsibility of installing, operating, adjusting,
maintaining, cleaning, repairing, & transporting the machine.
WARNING – UNAUTHORISED MODIFICATIONS/REPLACEMENTS/USE
The manufacturer declines any responsibility whatsoever, either civil of criminal, in the case of
unauthorised interference or replacement of one or more parts or assemblies on the machine,
or if accessories, tools & consumable materials used are different from those recommended by
the manufacturer, or if the machine is inserted in a plant system & its proper function is altered.
Brobo Group
brobo.com.au
2.1.1. Noise Level
The noise level of an idling saw has been measured to be below 85 dBA. This complies with the Australian
Occupational Health & Safety (Noise) Regulations 1992.
Please note that peak impulse noise levels will be experienced due to variables including blade characteristics, type,
& condition. This will also vary accordingly depending on the size & type of sample being cut. Under these
circumstances, management should make available to the operator(s) the appropriate hearing protection equipment
as prescribed under the above-stated act.
ALLUMINIUM
IN VACUM
Medium value of the sonorous level measured Lmp= 75,1 dB (A)
Value of the sonorous level in the working position measured Lmp= 81,3 dB (A)
Factor of environmental correction K= 1 dB (A)
Medium value of the correct sonorous level Lpc= 74,1 dB (A)
Value of sonorous level in the correct working position Lpc= 80,3 dB (A)
LOADED
Medium value of the sonorous level measured Lmp= 86,3 dB (A)
Value of the sonorous level in the working position measured Lmp= 91,1 dB (A)
Factor of environmental correction K= 1 dB (A)
Medium value of the correct sonorous level Lpc= 85,3 dB (A)
Value of sonorous level in the correct working position Lpc= 90,1 dB (A)
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Sierra de Brobo
Brobo
Brobo SA350H Manual de usuario
Brobo
Brobo OHS Series Manual de usuario
Brobo
Brobo S350D Manual de usuario
Brobo
Brobo S315G Manual de usuario
Brobo
Brobo VS400D Manual de usuario
Brobo
Brobo VS350D Manual de usuario
Brobo
Brobo VS315D Manual de usuario
Brobo
Brobo S315D, S350D, S400B Manual de usuario
Brobo
Brobo TNF-115 Manual de usuario
Brobo
Brobo FA 3000K Manual de usuario
