Broadcast IP Systems Avanti System Manual de usuario
Avanti System
A step-by-step Guide
Simple instructions on how to set up and test an i-Direct terminal for use on the Avanti platform
AVANTI (+44 207 749 6767)
_______________________________________________________________________________________________________________
Broadcast IP Systems
Lancaster Court |8 Barnes Wallis Road|Fareham|Hampshire|PO15 5TU|UK
Tel: +44 (0)1376 390647
www.broadcastipsystems.com
CONTENTS:
ANTENNA SET-UP (Holkirk TP100)
Tripod Assembly ..................................................................................................................... 2
Antenna Reflector Assembly .................................................................................................. 6
Antenna Alignment (using MPAD pointing aid) ................................................................... 13
Antenna Allignment (using i-Site)......................................................................................... 16
LOADING AN OPTION FILE........................................................................................................ 22
LOADING NEW FIRMWARE ...................................................................................................... 24
AVANTI (+44 207 749 6767)
_______________________________________________________________________________________________________________
Broadcast IP Systems
Lancaster Court |8 Barnes Wallis Road|Fareham|Hampshire|PO15 5TU|UK
Tel: +44 (0)1376 390647
www.broadcastipsystems.com
ANTENNA SET-UP (Holkirk TP100)
Tripod Assembly
Open Case 1
Reflector base petal
Antenna petal stack
Tri-pod mount
Open Case 2
L-Band cable
GPS
MPAD (cable) MPAD
(pointing aid)
AVANTI (+44 207 749 6767)
_______________________________________________________________________________________________________________
Broadcast IP Systems
Lancaster Court |8 Barnes Wallis Road|Fareham|Hampshire|PO15 5TU|UK
Tel: +44 (0)1376 390647
www.broadcastipsystems.com
Unpack the Quick deploy mount
Insert the tripod king post into the tripod legs
Secure with 3 thumb screws at the base of the tripod
Remove tripod from case 1
TIP: Try turning the
assembly over and resting the
head on the ground
Potential finger trap as the
king post enters the tripod legs -
be careful
TIP: Ensure the tripod leg
spider is in line with under-cut on
king post
AVANTI (+44 207 749 6767)
_______________________________________________________________________________________________________________
Broadcast IP Systems
Lancaster Court |8 Barnes Wallis Road|Fareham|Hampshire|PO15 5TU|UK
Tel: +44 (0)1376 390647
www.broadcastipsystems.com
Remove the feed arm assembly from the flight case and attach to the tripod
Secure the feed arm with Vee-clamps
Remove feed-arm assembly
from case 2.
Ensure the feed arm is
tensioned evenly
AVANTI (+44 207 749 6767)
_______________________________________________________________________________________________________________
Broadcast IP Systems
Lancaster Court |8 Barnes Wallis Road|Fareham|Hampshire|PO15 5TU|UK
Tel: +44 (0)1376 390647
www.broadcastipsystems.com
Raise the backing structure and lock into position with the securing dowels (X2)
Extend the transceiver cartridge
Unfold the feed arm/transceiver assembly
Potential finger trap as
the feed assembly is extended
NB: These surfaces must be
parallel (as shown) for correct
antenna geometry
AVANTI (+44 207 749 6767)
_______________________________________________________________________________________________________________
Broadcast IP Systems
Lancaster Court |8 Barnes Wallis Road|Fareham|Hampshire|PO15 5TU|UK
Tel: +44 (0)1376 390647
www.broadcastipsystems.com
Antenna Reflector Assembly
Remove the base petal and the centre petal from the antenna bag
Secure base petal to the antenna hub with latched over centre clamp
Locate antenna base petal into backing structure knife edge location
AVANTI (+44 207 749 6767)
_______________________________________________________________________________________________________________
Broadcast IP Systems
Lancaster Court |8 Barnes Wallis Road|Fareham|Hampshire|PO15 5TU|UK
Tel: +44 (0)1376 390647
www.broadcastipsystems.com
Secure the antenna to the backing structure with thumb nut (X2)
Start to assemble the reflector petals using the reflector edge clips
AVANTI (+44 207 749 6767)
_______________________________________________________________________________________________________________
Broadcast IP Systems
Lancaster Court |8 Barnes Wallis Road|Fareham|Hampshire|PO15 5TU|UK
Tel: +44 (0)1376 390647
www.broadcastipsystems.com
Front view of the first petal assembly
Repeat for petal 2
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Antena de Broadcast IP Systems
Manuales populares de Antena de otras marcas
Alfa Network
Alfa Network APA-L01 Manual de usuario
Naval
Naval PR-422CA Manual de usuario
Feig Electronic
Feig Electronic ID ISC.ANTH200/200 Series Manual de usuario
TERK Technologies
TERK Technologies TV44 Manual de usuario
Directive Systems & Engineering
Directive Systems & Engineering DSE2324LYRMK Manual de usuario
HP
HP J8999A Manual de usuario
