Briot Silver Manual de usuario
Dear Valued Customer,
You have acquired a Silver edger. We would like to thank you for the
confidence you have shown in our brand.
This edger has been manufactured with the greatest care. Before
using it in the best possible conditions, we advise you to read this
manual carefully and to keep it near your workstation, where you will
be able to refer to it easily.
The information contained in this manual does not form a contract
and can be modified without notice. Such a document may contain
errors or omissions although everything has been done to avoid
them. Briot cannot, in any circumstances, be held responsible for
any possible defects that might result from the errors or omissions.
2, rue Roger Bonnet
27340 PONT DE L'ARCHE
FRANCE
Tél. : (33) 02 32 98 91 32 - Fax : (33) 02 35 02 02 94
Table of contents
Silver FC 00 511 i
TABLE OF CONTENTS
ON-SITE REPAIR
Technician visits ______________________________________________________3
INSTALLATION / STARTING
General view _________________________________________________________7
Unpacking Machine ____________________________________________________8
Safety Precautions____________________________________________________11
Recommendations ________________________________________________________ 11
Installing the Machine ______________________________________________________ 11
USE
Introduction to the machine _____________________________________________17
Keypad/screen interface ____________________________________________________ 17
Scanform™ unit___________________________________________________________ 19
Basic Concepts ___________________________________________________________ 20
Precautions for use ___________________________________________________23
Standard use ________________________________________________________24
Creating a job ____________________________________________________________ 24
Tracing Mode ___________________________________________________________________ 24
Tracing a frame shape ____________________________________________________________ 25
Tracing a pattern or a demonstration lens shape ________________________________________ 26
Laying out and blocking a lens _______________________________________________ 28
Lay-out/Blocking Mode ____________________________________________________________ 28
Laying out and blocking the lens ____________________________________________________ 29
Edging a lens_____________________________________________________________ 32
Edging Mode____________________________________________________________________ 32
Edging a Lens ___________________________________________________________________ 33
Re-feeling a lens _________________________________________________________________ 35
Beveling a lens __________________________________________________________________ 36
Retouching a Lens _______________________________________________________________ 38
Operational limits _____________________________________________________39
Scanform™ unit___________________________________________________________ 39
Frame tracing limits ______________________________________________________________ 39
Pattern tracing limits ______________________________________________________________ 39
Lay-out /blocking unit_______________________________________________________39
Edging Station ____________________________________________________________ 39
Memory _________________________________________________________________ 39
MAINTENANCE
User maintenance ____________________________________________________43
List of accessories and consumables _____________________________________44
Accessories ______________________________________________________________ 44
Consumables ____________________________________________________________ 46
Settings and adjustments ______________________________________________47
Adjusting the screen contrast ________________________________________________ 47
Selecting a language_______________________________________________________ 48
Checking if the temperature compensation is activated/deactivated___________________ 48
Adjusting the size corrections ________________________________________________ 49
Table of contents
ii Silver FC 00 511
Emptying the internal memory________________________________________________ 50
Dressing the wheels _______________________________________________________ 51
Adjusting the lens sizes (reset sizes) __________________________________________53
Changing the lens feeler tip__________________________________________________ 57
Adjusting the Scanform™ ___________________________________________________ 58
Adjusting the lens feeling____________________________________________________64
Consulting the statistics_____________________________________________________ 65
Lens counters ___________________________________________________________________ 65
Wheel dressing __________________________________________________________________ 68
Lens feeler, lens size and Scanform™ adjustments _____________________________________ 69
Type of tracing __________________________________________________________________ 70
Messages __________________________________________________________71
Message types ___________________________________________________________ 71
List_____________________________________________________________________ 72
Origin: Scanform™ _______________________________________________________________ 72
Origin: Lay-out __________________________________________________________________ 72
Origin: Tracing __________________________________________________________________ 72
Origin: Edging ___________________________________________________________________ 73
Origin: Extension card ____________________________________________________________ 73
ANNEXES
Annex A Operation in recirculating mode
Installing the recirculating system ____________________________________________ A-3
Warning_______________________________________________________________________ A-3
Procedure _____________________________________________________________________ A-3
Illustration _____________________________________________________________________ A-3
Cleaning the Pump _______________________________________________________ A-4
Procedure _____________________________________________________________________ A-4
Emptying Main Tank ______________________________________________________ A-5
Annex B Use of the internal memory
Introduction _____________________________________________________________ B-3
Icons _________________________________________________________________________ B-3
Memory capacity________________________________________________________________ B-3
Using the internal memory__________________________________________________ B-4
Configuration___________________________________________________________________ B-4
Creating and Saving a Job ________________________________________________________ B-4
Advice ________________________________________________________________________ B-5
Call up a job saved in memory _____________________________________________________ B-5
Annex C Connection to the OMA network
Introduction _____________________________________________________________ C-3
Warning_______________________________________________________________________ C-3
Icons _________________________________________________________________________ C-3
Connection to the OMA network _____________________________________________ C-4
Configuration___________________________________________________________________ C-4
Creating and saving a job _________________________________________________________ C-4
Advice ________________________________________________________________________ C-5
Call up a job saved on the server ___________________________________________________ C-5
Job uploading function disabled ______________________________________________________ 6
Annex D Use of the barcode reader
Connection to the edger ___________________________________________________ D-3
Use ___________________________________________________________________ D-4
Annex E Technical Specifications
Technical characteristics ___________________________________________________ E-3
On-site Repair
On-site Repair
Silver FC 00 511 3
Technician visits
At each client visit, the Briot technician is asked to write in the following table.
Date of visit Name of the
technician
N° of the repair order
Installation / Starting
Tabla de contenidos
Otros manuales de Arista de Briot
