Brinsea Ovation 28 EX Manual de usuario

AF37 US Issue 01

Read the instructions before use! Do not cover!

Damaged appliances must not be used.

The appliance and its supply cord must be placed in an indoor area not subject to splashes of water or wet conditions and protected from or out of reach

of animals.

Repairs must be carried out only by a suitably qualified person.

This appliance must not be used, cleaned or maintained by children or persons with reduced physical, sensory or mental capabilities or lack of

experience and knowledge without supervision. Children must not play with the appliance.

Disconnect the incubator from the mains power supply during cleaning. Ensure that all electrical parts are kept dry.

Please read these instructions carefully before setting up your incubator to achieve best results and keep these instructions safe for future reference.

This document includes recommended procedures for successful hatching but incubation involves the control and manipulation of a large number of factors and in

certain circumstances different procedures may be necessary.

For more detailed information on all aspects of egg incubation including helpful advice on getting best results please visit our website at www.brinsea.com

Your incubator is designed to allow the user to vary the incubation conditions to suit a wide range of species in different ambient conditions and the specific set-up for

every situation is beyond the scope of these instructions.

For more information on incubation and hatching please download our FREE Incubation Handbook: www.brinsea.com/brochures/BrinseaIncubationHandbook2016.pdf

To register your new Brinsea product please visit www.brinsea.com and follow the link on the right hand side of the home page to qualify for your free 3 year

guarantee.

Record your appliance serial number here: __________________

AF37 US Issue 01

1Setting Up Your Incubator

Unpacking

Part Quantities

Assembly

Pump Setup

Location & Installation

2 Product Introduction –Functional Features

3Settings –Control Menu

4Display

5Temperature

6Humidity and Ventilation

7Eggs

8Periodic Incubation Cooling

9Hatching & Cleaning up

10 Specifications

CONTENTS

AF37 US Issue 01

1 SETTING UP YOUR INCUBATOR

UNPACKING

Your incubator has been supplied in protective

packaging. Please remove all tape, strapping and

packing from the incubator and parts. Retain the

carton and packing materials to enable the unit to

be repacked.

1: Remove the packaging and lift off the top of

the incubator.

2: Remove the card packing inserts and elastic

bands from inside the incubator.

3: Check that the electrical supply matches the

machine’s requirements (marked on the technical

label inside the clear top).

AF37 US Issue 01

1 SETTING UP YOUR INCUBATOR

PART QUANTITIES

The diagram shows all the parts that have been

supplied to you. Ensure you have the correct

quantities of each part. If there are any parts

damaged or missing please contact your retailer or

Brinsea Products (at the address at the end of the

document). Damaged appliances must not be

used.

1: Long Pump Connector

2: Water Pump Tubing (4.3” / 110mm)

3: Short Pump Connector

4: Pump Cover

5: Top

6:Egg Carriers (4)

7: Link

8: Water Pan Covers (2)

9:Water Evaporation Block

10: Base

11:Silicon Water Tubing (10’ / 3m)

AF37 US Issue 01

1 SETTING UP YOUR INCUBATOR

ASSEMBLY

1: There are two water pans. Fit the water

evaporation block into the correct water pan.

This is the one that has the water channel

flowing into it.

2: Place the water pan covers into their positions

in the base.

Do not add any water to the water pans.

Water Channel

Water Evaporation Block

AF37 US Issue 01

1 SETTING UP YOUR INCUBATOR

ASSEMBLY

3: Fit the link into its slots ensuring the smooth

side is facing inwards.

4: Fit the egg carriers into the supports. The pegs

must fit in the sockets.

Link slots

Detail A

Detail B

Detail A

Detail B

AF37 US Issue 01

1 SETTING UP YOUR INCUBATOR

ASSEMBLY

5: Place the top onto the base in the correct

orientation. The egg turning motor must sit over

the link. Check the top fits flush all the way

around the base edge.

6: Find a suitable water container (1pt to 2pt).

Place next to the incubator.

IMPORTANT: Do not place the water container

on top of the incubator or higher than the

incubator. This is to prevent the water siphoning

through and flooding the incubator. The water

container is best placed next to the incubator on

the same surface.

Please ensure the incubator is used on a water

resistant surface.

AF37 US Issue 01

1 SETTING UP YOUR INCUBATOR

PUMP SETUP

The Ovation EX incubator uses a peristaltic water

metering pump to automatically control the

relative humidity of the air in the egg chamber.

Pumped water is fed to an expanded paper

evaporation block where warm air is drawn over

the large surface to effectively evaporate all the

water (none should collect under normal

conditions). This humidified air is then mixed within

the heating chamber so that the air drawn across

the eggs is of uniform humidity and temperature.

The pump is supplied with a water pump tube (4.3”

/ 110mm) and two pump connectors that are fitted

at each end of the tube. Use the tube diagram to

ensure your tube is cut to the correct length.

1: Ensure the long pump connector is in the correct

position with the nozzle passing through the slot

into the incubator as shown.

2: Cut the water container tube to length (a length

of silicon water tubing to connect the pump to the

water container). Leave enough spare so that the

incubator top can be easily removed and placed to

one side. Attach one end of the water container

tube onto the other side of the short pump

connector and feed the tube into your water

container.

Nozzle passing through slot

into the incubator

Long Pump Connector

Short Pump connector

(4.3” / 110mm)

Tube diagram to scale

Water container tube

Water pump tube

AF37 US Issue 01

1 SETTING UP YOUR INCUBATOR

PUMP SETUP

3: Pull the short pump connector up over the

capstan, wrap around and pull over into the pump

connector’s slot. Follow the diagram on the

incubator, 1 –2 –3.

4: Fit the pump cover in place and gently tighten

the screw.

Check the water level in your water container

regularly.

Please check the condition of the tube after each

use. The peristaltic pump will need to have its

water pump tube replaced about every 3 months.

Cut a length of tube to 4.3” / 110mm. Remove the

connectors and pull off the old tube. Replace with

the new tube, avoiding twists. Use the diagram on

the product to assist and follow the instructions

above.

Pump Connectors Slot

Capstan

(3)

(2)

(1)

Screw

Pump cover

Tabla de contenidos

Otros manuales de Accesorios de Brinsea

Brinsea

Brinsea Ovation 28 Advance Manual de usuario

Brinsea

Brinsea OCTAGON 10 Manual de usuario

Brinsea

Brinsea Mini Eco Manual de usuario

Brinsea

Brinsea TLC-40 Eco Manual de usuario

Brinsea

Brinsea Ova-Easy Advance Series II Manual de usuario

Brinsea

Brinsea CONTAQ Z6 Manual de usuario

Brinsea

Brinsea Octagon 20 Advance Manual de usuario

Brinsea

Brinsea Maxi II eco Manual de usuario

Brinsea

Brinsea OvaView Manual de usuario

Brinsea

Brinsea Mini EX Manual de usuario

Brinsea

Brinsea Octagon 20 Eco Manual de usuario

Brinsea

Brinsea Ova-Easy Advance Series II Manual de usuario

Brinsea

Brinsea Ovation 56 ECO Manual de usuario

Brinsea

Brinsea Ovation 56 ECO Manual de usuario

Brinsea

Brinsea Mini Advance Manual de usuario

Brinsea

Brinsea Mini II Advance Manual de usuario

Brinsea

Brinsea Octagon 40 Eco Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario