Briggs & Stratton 1696783 Manual de usuario

Not for

Reproduction

ATTACHMENT

OPERATOR’S

MANUAL

80024713

Rev.: A

Mfg. No. Description

1696783 Turbo, 52” Fabricated Mower Deck

Turbo Vacuum System

Not for

Reproduction

Table of Contents

Operator Safety ............................................................................. 3

Parts / Hardware ............................................................................ 5

Assembly ....................................................................................... 6

Mower Preparation - Disassembly............................................. 6

Install Turbo Assembly............................................................... 7

Install New Pulley Cover............................................................ 8

Operation ....................................................................................... 9

Before Operation ....................................................................... 9

Mowing with the Turbo............................................................... 9

Mowing without the Turbo.......................................................... 9

Recommended Accessories ..................................................... 9

After Operation.......................................................................... 9

Turbo Removal............................................................................... 10

Removing the Turbo................................................................... 10

Storage ........................................................................................... 11

Warranty ......................................................................................... 12

NOTE: In these instructions, “front”, “back”, “left” and “right” are

referenced from the operating position.

Not for

Reproduction

General Information

For additional information, refer to the Customer Contact

Guide and Setup Instructions included with unit.

The illustrations in this document are representative.Your

unit may vary from the images displayed. LEFT and RIGHT

are referenced from the operator’s position.

The use of Important and Note in the text indicates

clarications, exceptions, or alternatives to the procedures

given.

All language translations of this document are derived from

the original English source le.

Operator Safety

Save these instructions for future reference. This

manual contains safety information to make you aware of

the hazards and risks associated with the product and how

to avoid them. It also contains important instructions that

should be followed during the initial set-up, operation, and

maintenance of the product.

It is important that you read and understand these

instructions before attempting to start or operate this

equipment.

Be thoroughly familiar with the controls and the proper use

of the front loader.Know how to stop the unit and disengage

controls quickly.

Safety Alert Symbols and Signal Words

The safety alert symbol indenties safety information

about hazards that can result in personal injury. A signal

word (DANGER, WARNING, or CAUTION) is used with the

alert symbol to indicate the likelihood and the potential

severity of injury. In addition, a hazard symbol may be used

to represent the type of hazard.

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazard which, if not avoided,

could result in death or serious injury.

CAUTION indicates a hazard which, if not avoided,

could result in minor or moderate injury.

NOTICE indicates an action that could result in damage to

the product.

Hazard Symbols and Meanings

Symbol Meaning Symbol Meaning

Safety informa-

tion about haz-

ards that can

result in person-

al injury.

Read and

understand

the operator’s

manual before

operating or

servicing the

unit.

U.S.A. Models: Certain components in this product and

its related accessories contain chemicals known to the

State of California to cause cancer, birth defects, or

other reproductive harm. Wash hands after handling.

Not for

Reproduction

Operator Safety / TURBO

Operator Safety WITH TURBO

WARNING

• When blower assembly is removed from the mower

deck, the deflector must be properly installed.

• If the mower stalls or the turbo blower chute plugs,

disengage the electric clutch (PTO), stop the engine

and remove the key. set the parking brake. wait for

moving parts to stop. Remove the foreign object or

clear the chute with a piece of wood before restarting

the engine. Never place hands into blower housing to

clear jammed object.

• Disengage the electric clutch (PTO). Shut off the

engine, remove the key, and wait for all moving parts

to stop before attaching, adjusting, or disconnecting

any part of the collection system.

• Read and obey all WARNING decals.

Part No. 1700259

Amputation Danger Decal

Operation Safety WITHOUT Turbo

WARNING

• For operation without the turbo, the deflector

must be properly installed in the down position and

retained by the spring latch.

Safety Decal

Part No. 5103184

Amputation Warning Decal

Not for

Reproduction

A- PULLEY ASSEMBLY, (Qty. 1)

D- PULLEY COVER, (Qty. 1)

B- CARRIAGE BOLT,

.3125” -18 x 1.25, (Qty. 1) C- RETAINER,

.3125”, (Qty. 1) F- SNAPPER PIN,

(Qty. 2)

E-TURBO ASSEMBLY, (Qty. 1)

G- FLAT WASHER,

.3125”, (Qty. 1) H- LOCKWASHER,

.3125”, (Qty. 1) I- KNOB,

(Qty. 1)

Parts / Hardware

HARDWARE BAG 1756733

Not for

Reproduction

Assembly

WARNING

Before beginning any service work turn off the PTO, set

the parking brake, turn off the ignition, and disconnect

the spark plug wire(s).

Mower Preparation - Disassembly

1. Park tractor on a hard, level surface such as a concrete

floor. Engage parking brake, disengage PTO, and stop

engine.

2. Set deck to the lowest position.

3. On discharge side of mower, loosen taptites (a, Figure

1) securing pulley cover (b). Remove and retain existing

pulley cover.

Figure 1

4. Using a pry bar, place the square end in the square hole

located in the end of the idler arm (c, Figure 2).

WARNING

Use extreme caution when rotating the idler arm with the

breaker bar, due to the increased tension in the spring

as the idler arm is being rotated. Injury may result if the

breaker bar is prematurely released while the spring is

under tension.

5. Carefully rotate the idler arm counter-clockwise.

6. Slide the mower drive belt (d) over the edge of the

right hand spindle pulley (e).

Figure 2

7. For ease of disassembly in Step 8, wedge a wooden

block between the mower blade and the mower deck

housing to keep the mower blade from turning (Figure

3).

Figure 3

8. Remove and retain nut (f, Figure 4), belleville washer

(g), key (h) and remove and discard existing pulley (i).

Figure 4

Not for

Reproduction

Install Turbo Assembly

1. Park tractor on a hard, level surface such as a concrete

floor. Engage parking brake, disengage PTO, and stop

engine.

2. Install new pulley assembly (A, Figure 5) with large

diameter pulley down.

3. Insert key (h) and belleville washer (g) with concave

side facing Down. Secure with nut (f). Torque to 65-75

lbs. ft. (88.1-101.6 Nm).

Figure 5

4. Remove wooden block in the mower deck.

5. Re-install drive belt (d, Figure 6) onto the lower pulley

of the pulley assembly (A). Roll belt downward while

rotating pulley assembly until belt is in place.

Figure 6

6. On the inside of discharge opening, insert carriage bolt

(B, Figure 7) through slot and secure with retainer (C).

Figure 7

7. Rotate deflector and place in the upright position.

8. (Assistance maybe needed to perform this step). Place

turbo (E, Figure 8) onto discharge opening, aligning

deck tabs (j) with turbo tabs (k). Belt (l) needs to slide

through opening between deflector and deflector

bracket. Ensure carriage bolt (B) on deck aligns with slot

(m) on turbo.

Figure 8

Not for

Reproduction

9. On right side, align holes of deck tab (o, Figure 9) with

holes of turbo tabs (p) and secure with snapper pin (F).

10. On left side, pull back on idler arm (n). Align holes

of deck tab with holes of turbo tabs and secure with

snapper pin.

Figure 9

11. Install turbo belt (l, Figure 10) onto top pulley of pulley

assembly (A) using belt tension arm (n) for assistance.

Figure 10

12. Ensure belt is routed as shown in Figure 11.

l A

Figure 11

13. Secure turbo to deck with flat washer (G, Figure 12),

lockwasher (H) and knob (][ ).

][

Figure 12

Install New Pulley Cover

1. Align notches of new pulley cover (D, Figure 13) with

taptite screws in deck plate. Tighten tapetites (a).

Figure 13

Not for

Reproduction

Operation

Before Operation

Clear the lawn of all sticks, stones, wire and other debris

which may be caught or thrown by the mower blades.

For best results, mow when the grass is dry. Wet grass

tends to clump and plug up the mower and grass catcher

For efficient grass collection, air circulation under

the mower deck, through the chute and into the

grass catcher or cart is very important.

For this reason, BEFORE YOU BEGIN MOWING you

should make certain the underside of the mower and

the underside of the catcher lid are free from grass and

debris.

Make sure that there is a snug fit between mower deck,

blower housing, tubes, and grass catcher cover.

Mowing with the Turbo

Always operate with engine running at full speed when

mowing.

Grass should be cut often, and not too short. If grass is too

long or lush it may be necessary to keep ground speed

to a minimum or to cut only half the width of the mower to

prevent clogging. If grass is long, operate with mower in

high cutting position for first pass, cutting again in a lower

position on a second pass.

Look through the grass catcher tube to check for grass

flow. Do not open the grass catcher cover with mower

engaged.

If a large amount of cut grass is spilling out from under the

deck, the tube may be plugged or the catcher may be full.

Discontinue mowing, stop the tractor, disengage the PTO

and then empty the catcher or clear the tube.

WARNING

ALWAYS shut off the tractor. Disengage the PTO, and

allow all moving parts to stop BEFORE disconnecting or

clearing tube, or emptying grass bags.

Before leaving the operator’s position for any reason,

engage the parking brake, disengage the PTO, stop the

engine and remove the key.

To reduce fire hazard, keep the engine, tractor and

mower free of grass, leaves and excess grease. Do not

stop or park tractor over dry leaves, grass or combustible

materials.

Mowing without the Turbo

If you need to mow without the turbo vacuum system in

place (for instance, if the grass is too wet to bag, but must

be mowed), you must remove the turbo from the mower

deck, and properly position the deflector BEFORE you

begin mowing.

WARNING

To operate without the collection system, the turbo

assembly MUST be removed and the deflector MUST be

in the down position.

The deflector is spring loaded. When removing the turbo,

hold the deflector up; then lower the deflector into the

normal operating position.

Recommended Accessories

If operating on slopes when a rear attachment is installed,

use front counterweights. Never operate on slopes greater

than 10°.

After Operation

The turbo housing and grass catcher tube should be

removed for cleaning. Remove the tube by unlatching

the lower tube rubber band from turbo housing. When

reattaching, make sure there is a snug fit between the

mower deck, turbo housing, and grass catcher.

Not for

Reproduction

Turbo Removal

DANGER

To operate without the collection system, the turbo

assembly MUST be removed and the deflector MUST be

in the down position.

The deflector is spring loaded. When attaching or

removing the turbo, hold the deflector up; then lower the

deflector into the normal operating position.

Removing the Turbo

For operation without turbo, the deflector must be properly

installed in the down position and retained by the spring

latch.

1. Remove the grass discharge tubes.

2. Remove knob (I, Figure 14), lockwasher (H) and flat

washer (G) from carriage bolt that secures turbo to

deck.

Figure 14

4. Pull back on the belt tension arm (n, Figure 15) to

slacken the belt.

5. Remove the belt (l) from the top pulley of the pulley

assembly (A).

l A

Figure 15

6. On left side, remove snapper pins (F, Figure 16) from

deck tabs (o) and turbo tabs (p).

7. On left side, pull back on idler arm (n). Align holes

of deck tab with holes of turbo tabs and secure with

snapper pin.

Figure 16

8. Assistance maybe needed to perform this step. Remove

turbo (E, Figure 17) from the discharge opening.

Figure 17

WARNING

The deflector must be returned to the down position. Do

not operate the unit without a deflector.

Tabla de contenidos

Otros manuales de Cortacésped de Briggs & Stratton

Briggs & Stratton

Briggs & Stratton BRUTE BTXP226750HW Manual de usuario

Briggs & Stratton

Briggs & Stratton 2691691-00 Manual de usuario

Briggs & Stratton

Briggs & Stratton 1756276 Guía de referencia

Briggs & Stratton

Briggs & Stratton BRUTE BTPV21675E Manual de usuario

Briggs & Stratton

Briggs & Stratton 360Z XT Manual de usuario

Briggs & Stratton

Briggs & Stratton 5900664 Manual

Briggs & Stratton

Briggs & Stratton 7800950-01 Manual de usuario

Briggs & Stratton

Briggs & Stratton 1600 Manual de usuario

Briggs & Stratton

Briggs & Stratton 2691184-00 Manual de usuario

Briggs & Stratton

Briggs & Stratton 2691251-00 Manual de usuario

Briggs & Stratton

Briggs & Stratton Snapper 2691382-00 Manual de usuario

Briggs & Stratton

Briggs & Stratton Simplicity Axion CZT2142 Manual de usuario

Briggs & Stratton

Briggs & Stratton 42 Manual de usuario

Briggs & Stratton

Briggs & Stratton 2691351-00 Manual de usuario

Briggs & Stratton

Briggs & Stratton BRUTE BTPV22675E Manual de operación y mantenimiento

Briggs & Stratton

Briggs & Stratton Ferris IS5100Z Series Manual

Briggs & Stratton

Briggs & Stratton Legacy XL Manual de usuario

Briggs & Stratton

Briggs & Stratton FW25 series Manual

Briggs & Stratton

Briggs & Stratton Prestige 1800 Series Manual de usuario

Briggs & Stratton

Briggs & Stratton Brute 1800833 Manual de usuario

Briggs & Stratton

Briggs & Stratton 1695776 Manual de usuario

Briggs & Stratton

Briggs & Stratton Zero Turn Rider Manual de usuario

Briggs & Stratton

Briggs & Stratton SNAPPER 5900731 Manual de usuario

Briggs & Stratton

Briggs & Stratton 2691266-00 Manual de usuario

Manuales populares de Cortacésped de otras marcas

RHINO

RHINO 1958 Manual de usuario

Wolf Garten

Wolf Garten Compact plus 40 B Manual de usuario

Cub Cadet

Cub Cadet LTX 1045 Manual de usuario

Craftsman

Craftsman 917.378461 Manual de usuario

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Manual de usuario

Challenge

Challenge CH18V2 Instrucciones de operación

TALEN TOOLS

TALEN TOOLS AVR HGM30 Manual de usuario

DEWEZE

DEWEZE ATM-725 Manual de operación

Weed Eater

Weed Eater 180083 Manual de usuario

Husqvarna

Husqvarna Poulan Pro PP185A42 Manual de usuario

Better Outdoor Products

Better Outdoor Products Quick Series Manual de usuario

Cub Cadet

Cub Cadet 23HP Z-Force 60 Manual de funcionamiento

MTD

MTD 795, 792, 791, 790 Manual de usuario

Toro

Toro Groundsmaster 3505-D Manual de usuario

Dennis

Dennis FT 610 Manual de usuario

AIRFORCE

AIRFORCE F-15 Gen 3 Manual de usuario

MTD

MTD 126-220-000 Manual de usuario

Toro

Toro 74806 Manual de usuario