Brel-motors BTE50 Manual de usuario

Pagina 1

Manual bi-directional electronic radio motor with twisted wand

Type BTE50

Read the manual before you begin the installation If these instructions are not followed,

this may lead to defects and injury in which warranty can’t be claimed

Warning:

Children cannot recognise the dangers of this electrical equipment and should therefore not work with it.

It is important to follow this manual carefully for your own safety

1. Do not work with the motor in humid environments.

2. The motor must be installed correctly.

3. eep the antenna in good condition and do not shorten it.

The antenna must not come into contact with other

metal parts otherwise the operation will be reduced.

4. The motor must be protected against direct moisture.

5. BREL-Motors declares that this motor has been manufactured

according to the guidelines of the CE standard 1999/5/EC.

_______________________________________________________________________________

Functions remote control Changing batteries

DD-2702H

Works with all BREL transmitters:

Always check that the remote control is in Bi-directional mode!

Re er to manuals or remote controls at:

www.brel-motors.nl

______________________________________________________________________________

Technisch gegevens van de motor Type BTE50-0 6

 Voltage motor: 8.4 V

 Vermogen: 5 Watt

 Draaimoment: 0.6 Nm

 Toerental: 10 RPM

 Ampèrage: 0.54 A

 Vocht- en stofwerendheid: IP20

 Opslagcapaciteit zenders is maximaal 10 kanalen.

Page 2

MOTOR ADJUSTMENT CHARGING POINT BATTERY

_______________________________________________________________________________

Wiring diagram

BATTERY

Charging point

----Antenna

Connection point -----

. /

Programm button P1

_______________________________________________________________________________

Step 1 Setting up the first remote/channel

P1 until 







 STOP until 2x 









Hold down the P1 button until the Press and hold the STOP button until the product Transmitter/channel

product moves up and down. The motor beeps. moves 2x up and down and beeps 3x. has been set.

If NO end positions are set, the product will move in the pulse / step operation Go then to STEP 2.

I end positions are set, the product will continue to its end position. Go then to STEP 4.

WARNING: It is possible that the correct end positions have not been set. Go then to OPTION A.

______________________________________________________________________________

Step 2 Adjusting the direction of rotation(Only if the direction of rotation is not correct)

Only possible i no end positions are set, otherwise irst option C (Delete end positions), a ter that, Step 2.

1x ▲ until 1x 



 ▲+▼ until 1x 









Press 1x the P1 button shortly, Press UP and DOWN button The direction of rotation of

until the product moves down. simultaneously, until the product moves. the motor is OK

Page 3

_______________________________________________________________________________

Step 3 Setting the end limits

1 Set the desired top position





 ▲+ STOP 2x 









Use the OPERATING buttons to Press UP and STOP simultaneously, The desired top

move the product to the desired top position. until the product moves 2x and beeps 3x. position is set.

2 Set the desired bottom position





 STOP+▼ 2x









Use the OPERATING buttons to move Press DOWN and STOP simultaneously, The desired bottom

the product to the desired bottom position. until the product moves 2x and beeps 3x. position is set.

_______________________________________________________________________________

Step 4 Setting the desired third limit position (If desired)





 1x P2 1x 







 1x STOP 1x 







 1x STOP 2x 









Set the desired Press 1x P2. Press 1x STOP button. Press 1x STOP button.

Third limit The product moves 1x The product moves 1x The product moves 2x up

position. up and down and beeps. up and down and beeps. and down and beeps 3x for confirmation.

Press and hold STOP or 3 seconds to move to the set limit position.

The motor is now ready or use!

______________________________________________________________________________

Additional settings

____________________________________________________________________________

Option A Adjusting the top position

If adjustment is not possible, go to Option C, then to Step 3





 STOP +▲ until 







 



 STOP +▲ until 2x 









Go to the already Press at the same time Go to the new Press at the same time

set top position, STOP and UP until top position. STOP and UP button, until

the motor moves and beeps 1x. the motor 2x moves and 3x beeps.

Page 4

___________________________________________________________________________

Adjusting the down position

If adjustment is not possible, go to Option B, then to Step 3





 STOP +▼ until 







 



 STOP +▼ until 2x 









Go to the already Press at the same time Go to the new Press at the same time

set bottom position, STOP and DOWN until bottom position. STOP and DOWN button, until

the motor moves and beeps 1x. the motor 2x moves and 3x beeps.

_______________________________________________________________________________

Option B Pulse / jog control

1x 







 , beeps 1x

▲+▼ until 1x 







 1x STOP

Pulse / jog on

Pulse / jog off

Press and hold UP and DOWN button, Press 1x STOP button.

until the product moves up and down.

2x 







 , beeps 3x

_______________________________________________________________________________

Option C Deleting the third limit position

1x P2 1x 







 1x STOP 1x 







 1x STOP 1x 









Press 1x P2. Press 1x STOP button. Press 1x STOP button. The third limit positions

The product moves 1x up The product moves 1x up The product moves 1x up are now deleted from

and down and beeps 1x. and down and beeps 1x. and down and beeps 1x the memory.

for confirmation.

_______________________________________________________________________________

Option D Learn new transmitter/channel while maintaining end limits

Only possible when end limits are set.

= Already existing transmitter = New transmitter

Method 1

P2 a until 







 P2 a until 







 STOP b until 2x 









Press P2 of a. The product Press P2 of a. The product Press STOP of b. The product The transmitter b

moves 1x up and down moves 1x up and down moves 2x up and down has been added.

and beeps 1x. and beeps 1x. and beeps 3x.

Repeating the above will remove the new transmitter/channel.

Page 5

Method 2

P2 a until 







 P2 a until 







 P2 b until 2x 









Press P2 of a. The product Press P2 of a. The product Press P2 of b. The product The transmitter b

moves 1x up and down moves 1x up and down moves 2x up and down has been added.

and beeps 1x. and beeps 1x. and beeps 3x.

Repeating the above will remove the new transmitter/channel.

Method 3 (In case the old station is lost or de ective)

P1 tot 1x 







 STOP b tot 2x 









Press P1 of a. The product moves 1x Press 1x STOP of b. The product The transmitter b

up and down and beeps 2x. moves 2x up and down and beeps 3x. has been added.

Repeating the above will remove the new transmitter/channel.

______________________________________________________________________________

Option E Speed control

1x 



 A 1x 



 A

1x P2 A until 







 O

Press 1x up of A. Press 1x up of A. The motor speed

has been increased

1x 



 A 1x 



 A

Press P2 of a. The product Press 1x down of A, Press 1x down of A, The motor speed

moves 1x up and down. button A in. button A in. has been reduced.

I the motor does NOT react a ter this action, it is already at the highest or lowest speed.

Page 6

_______________________________________________________________________________

Additional settings P1 button

Can be used without a transmitter as an operating button

1x P1

The product moves up, stops or goes down when pressed P1

Press 1x P1 on the motor.

_______________________________________________________________________________

Switching off the receiver

P1, (6 sec ) until 2th x 









Press and hold P1 until the product moves The Receiver switched off.

up and down for the 2th time and beeps 2x.

To reactivate the receiver, brie ly press P1 once.

_______________________________________________________________________________

Changing the direction of rotation

P1, (10 sec ) until 3th x 









Press and hold P1 until the product moves The direction of rotation has changed.

up and down for the 3th time and beeps 3x

_______________________________________________________________________________

Reset to factory settings

P1, (14 sec ) until 4th x 









Press and hold P1 until the product moves Resets to factory settings

up and down for the 4th time and beeps 4x

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Motor de brel-motors

brel-motors

brel-motors MGLE-45 Manual de usuario

brel-motors

brel-motors MS55-60 Manual de usuario

brel-motors

brel-motors MLE Series Manual de usuario

brel-motors

brel-motors BGLE-980 Manual de usuario

brel-motors

brel-motors BLE 25 Manual de usuario

brel-motors

brel-motors MJE24S Manual de usuario

brel-motors

brel-motors BTE 50 Manual de usuario

brel-motors

brel-motors MR45-20 Manual de usuario

brel-motors

brel-motors BRE45 Manual de usuario

brel-motors

brel-motors MGS-45 Manual de usuario

brel-motors

brel-motors BJE24DD Manual de usuario

brel-motors

brel-motors BR35 Manual de usuario

brel-motors

brel-motors MG-45 Manual de usuario

brel-motors

brel-motors BJE24TD Manual de usuario

brel-motors

brel-motors BJE24S Manual de usuario

brel-motors

brel-motors MTE50-0.6 Manual de usuario

brel-motors

brel-motors MJE24D Manual de usuario

Manuales populares de Motor de otras marcas

Rotax

Rotax 125 senior MAX evo Manual de usuario

Kohler

Kohler K361 Manual de usuario

MTD

MTD OHV Series Manual de usuario

Kohler

Kohler COMMAND CH18-745 Manual de usuario

Mercury

Mercury D4.2L D-Tronic Manual de usuario

Selve

Selve SE Plus-RC Series Manual de usuario

Perkins

Perkins 1206E-E66TA Manual de usuario

Skov

Skov DA 174 Manual

Rossi

Rossi TX11 Series Manual de usuario

Siemens

Siemens SIMOTICS T-1FW3 Hoja de instrucciones

AL-KO

AL-KO PRO 350 Manual de usuario

MTU

MTU 12 V 4000 Lx4 Manual de usuario

Nanni

Nanni N3.30 Manual de instrucciones

Nanni

Nanni N5.160 CR2 Manual de usuario

KSB

KSB SuPreme Series Instrucciones de instalación

Hiwin

Hiwin EM1 Series Manual de usuario

Rotax

Rotax 912 i series Instrucciones de funcionamiento

Siemens

Siemens SIMOTICS XP 1MB1 Manual de usuario

brel-motors BTE50 Manual de usuario

Manuales populares de Motor de otras marcas