Brandt VF400JU1 Manual de usuario
EN
Pages
Installing your dishwasher....................................31-36
Levelling by adjusting the feet .................................31
Anti-condensation protection ...................................31
Facing the door ......................................................32
Balancing the door .................................................32
Building in and fixing the dishwasher.......................32
Water connections ..................................................33
Draining away the waste water................................34
Electrical connection ...............................................34-35
Foam strip and soundproofing sea ...........................36
Installing the plastic corner brackets........................36
Safety instructions ...............................................36
Building in under a hob.........................................36
Contents
30
EN 31
Installing your dishwasher
Levelling by adjusting the feet
Ensure that your dishwasher is well
balanced and stable. The four feet can
be adjusted, so adjust them if necessary
using a screwdriver. If the feet are
poorly adjusted, this decentres the door
and makes your dishwasher wobble,
causing leaks.
For dishwashers that can be built-in,
fitted with rear feet adjustment via two
knurled knobs on the base of the
machine, at the front, use a screwdriver,
without exerting force, to finish the
adjustments to avoid damaging the
worktop.
Protecting the worktop
Glue the steam protector supplied with
your machine underneath your worktop.
Built-in appliance cup kit
(available according to the model from
After-Sales or the dealers)
To assist in sliding your dishwasher
(over rough or carpeted floors, etc.),
clip the little cups to all four feet.
Remove the 2 red
protective wedges from
the front of your appliance to
avoid causing a leak.
32
Facing the door
To fit a door to match your units
onto the dishwasher’s door, use the
installation template and the
accessories supplied with your
machine.
Balancing the door (right and
left)
Adjust the tension on the springs, if
required, to compensate for the
weight of the facing panel. Adjust in
an identical fashion to the right and
to the left.
Fix your dishwasher to the worktop
with two screws under the front
corner bracket.
If your worktop is marble or a
similar material, you can fasten
your dishwasher in place at the
sides using two brackets (available
from the After-Sales department or
from your dealer).
Installing your dishwasher
This dishwasher
must operate with a
wood panel.
EN
Installing your dishwasher
33
EN
Tap: with threaded end, 20/27mm
dia. (3/4” BSP)
Flow: 10l/min. minimum
Pressure: 1 bar to 10 bars
(0.1 - 1 MPa)
In the event of high pressure, it is
advisable to fit a pressure regulator.
Your Water Company will give you
the necessary information.
Length of the water supply pipe
(standard unit): 1.50m
Connecting the hot water:
Check that your original hose is
designed for connection to the hot
water supply (red marking on the
hose).
If necessary, you can alter the
hose’s direction. To do this, loosen
the connection at the bottom left
on the rear of the machine and
swivel it as necessary. Fully tighten
the connection again and check
that there are no leaks.
For dishwashers fitted
with safety hoses:
You must remove the
protective cover (see
the drawing opposite)
to alter the hose’s
direction. To do this,
loosen the two
screws (end fitting
T20), remove the
protective cover,
position the
connection in the
direction you wish and then
replace the protective cover.
If you use a self-
piercing tap, check that
there is sufficient water flow.
When the tap is on the left-
hand side of the machine, use the
“anti-kinking” hook supplied with the
machine to avoid any risk of the
supply hose* kinking while you are
fitting your dishwasher.
(* For large diameter safety hoses-
depending on the model)
Check that the
seal is fitted
and that the
connection is
tight.
When you are making a
new installation, you must
use a new hose to connect the
machine to the water supply: you
must not re-use the old hose.
Water connections
“Hazardous Voltage” symbol
(depending on the model)
the hose is fitted with an electrical
device
Important :
check the water’s
hardness: all the
information you
require is provided in
the Chapter
“Adjusting the water
softener” in your
operating instructions
manual.
0,1 - 1 MPa
34
Installing your dishwasher
EN
Draining away the waste water
Length of the drain hose: standard
1.50m. If necessary, you can
increase the length of the drain
hose (4m max.). In this case, check
that the machine drains correctly.
Connect the drain hose:
- To a ventilated siphon
- To a sink U-bend
Remove the stopper form the
U-bend.
Remove the rubber stopper and, if
necessary, add a collar.
- Directly to your sink.
Ensure that you hold your drain
hose in place with the end
connector to avoid flooding.
For machines installed in columns,
the height of the drain hose must
not be higher than the top of the
machine.
Electrical connection
Mains voltage: 230V
Fuse: 10A, 13A or 16A
The socket outlet must be
grounded to Earth.
In all cases, the connection must
comply with the standards in force
in the country concerned, together
with the supplementary regulations
of the Electricity Authority. The
machine must be switched off when
the connection is made to the
electrical circuit.
If you have any doubts regarding
the condition of your installation, do
not hesitate to have it checked by a
qualified electrician.
The machine must be installed so
that the socket remains accessible.
We cannot be held
liable for any damage
caused by the faulty earthing
of the machine.
NB: Pull the pipe
gradually when
installing it to avoid
kinking it.
Do not use an electrical extension,
a double socket or an electrical
timer. The installation must comply
with the country’s prevailing norms.
Your dishwasher complies with
European Directives 73/23/EEC
(Low Voltage Directive) and
89/336/EEC (Electromagnetic
Compatibility), modified by
Directive 93/68/EEC.
Installing your dishwasher
35
EN
Replacing the power
cable
For your safety, this operation
must be performed by the
manufacturer’s After-Sales
department or a person with
similar training and experience
in order to avoid any risk.
IMPORTANT for the dishwasher without plug.
The wires in this mains lead ar coloured in accordance the
following code :
Green & Yellow Earth
Blue Neutral
Brown Live
As the colours of the wires in the mains lead of this appliance may not
correspond with the terminal in your plug, proceed as follows ; The wire
which is coloured Green and Yellow must be connected to the terminal
which is marked with the letter «E» or by the earth symbol or
coloured Green end Yellow.
The wire which is coloured Blue must be connected to the terminal
which is marked with the letter «N» or coloured Black.
The wire which is coloured Brown must be connected to the terminal
which is marked with the letter «L» or coloured Red.
EN
36
Installation of the adjustable
plinth on built-in appliances
(depending on the model)
AVAILABLE FROM
THE AFTER-SALES
DEPARTMENT UNDER
REFERENCE: 32X0050
Installing your dishwasher
Foam strip and soundproofing
seal. To provide better noise
insulation on built-in appliances,
install the soundproofing seals and
the foam strip supplied with your
machine
(depending on the model).
Safety instructions
Building in under a hob
If your dishwasher is being installed on a carpeted floor, make
sure to adjust the feet to leave a ventilation space under the
machine
If your worktop is fitted with a built-in hob over your
dishwasher, you must provide thermal insulation on top of the
machine. You can obtain this insulation kit from your dealer. Take care
to leave a space between the gas pipe and the top of your machine.
If the machine is operating incorrectly, disconnect it from the
electricity supply (remove the plug) or switch off the circuit involved
and close the water supply tap. Contact our After-Sales department.
For your safety’s sake, never leave your dishwasher’s door fully
open after use.
Tabla de contenidos
Otros manuales de Lavavajillas de Brandt
Brandt
Brandt VI 320 Manual de usuario
Brandt
Brandt DWE 500 Manual de usuario
Brandt
Brandt BF3424CW Manual de usuario
Brandt
Brandt VF 320 Manual de usuario
Brandt
Brandt BDB424DX Manual de usuario
Brandt
Brandt BDJ424DB Manual de usuario
Brandt
Brandt VH1520J Manual de usuario
Brandt
Brandt VH1505W Manual de usuario
Brandt
Brandt BDF534DW Manual de usuario
Brandt
Brandt VS1009X Manual de usuario
Brandt
Brandt BF3534CW Manual de usuario
Brandt
Brandt VF 300 Series Manual de usuario
Brandt
Brandt DSF13526W Manual de usuario
Brandt
Brandt DWJ127DS Manual de usuario
Brandt
Brandt VH1542J Manual de usuario
Brandt
Brandt VS1009J Manual de usuario
Brandt
Brandt DW9 Manual de usuario
Brandt
Brandt VH1544X Manual de usuario
Brandt
Brandt DVC1434JU Manual de usuario
Brandt
Brandt VH1772X Manual de usuario
