Brady 1024 Manual de usuario
BradyprinterTHT Model
1024 Thermal Transfer Printer
_______________________________________________________________________________
User’s Guide
LOGO W.H. Brady Co.
Automatic Indentification Products
CG Triumvirate is a trademark of Agfa Corporation.
Corrupad is a Trademark of Corrupad Protective Packaging Inc.
Bradyprinter THT Model 1024 is a Trademark of Brady USA Inc.
As an Energy Star Partner, Brady USA Inc. has determined that this
product meets the Energy Star guidelines for energy efficiency.
Information in this document is subject to change without notice and does
not represent a commitment on the part of Brady USA Inc. No part of this
manual may be reproduced or transmitted in any form or by any means,
for any purpose other than the purchaser's personal use, without the
expressed written permission of Brady USA Inc.
All rights reserved. Printed in the United States of America.
© Copyright 1997 by Brady USA Inc.
6555 W. Good Hope Road •Milwaukee, Wisconsin •53223
800-537-8791 Customer Support
800-643-8766 Technical Support
Part Number: 88-2184-01
Revision: C
Agency Compliance and Approvals:
FCC: This device complies with Part 15 of FCC rules.
Note: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and
can radiate radio frequency energy, and if not installed and used
in accordance with the instructions in this manual, it may cause
harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.
Important Safety Instuctions
Your Bar Code Printer has been designed to give you many years of
safe, reliable service. As with all electrical equipment, there are a few
basic precautions you should take to avoid getting hurt or damaging the
Printer.
•Carefully read the installation and operating instructions provided
with your Printer.
•Read and follow all warning instruction labels on the Printer
itself.
•Place the Printer on a flat, firm, solid surface.
•To protect your Printer from overheating, make sure all openings
on the Printer are not blocked.
•Do not place the Printer on or near a heat source, (i.e., a radiator
or heat register).
•Do not use your Printer near water, or spill liquid of any kind into
it.
•Be certain that your power source matches the rating listed on the
bottom of the Printer. If you are unsure, check with your dealer
or with your local power company.
•Do not place the power cord where it will be walked on. If the
power cord becomes damaged or frayed replace it immediately.
•Do not insert anything into the ventilation slots or openings on the
Printer.
•Only qualified, trained service technicians should attempt to
repair your Printer.
i
♦♦ Contents
♦♦ Getting Started
1.0 Introduction ...............................................................1
1.1 Unpacking and Inspection...........................................1
1.2 Printer Specifications .................................................2
1.3 Connecting Power......................................................4
1.4 Switches and Indicators..............................................5
1.5 Interfacing to the Printer.............................................6
1.6 Loading Media...........................................................7
1.7 Loading Media for Peel Configuration........................8
1.8 Loading Ribbon (Thermal Transfer)..........................9
1.9 Adjusting for Wide to Narrow Media........................11
1.10 Power-up Configuration and Self-Test......................12
1.11 Available Options ....................................................13
♦♦ Printing Labels
2.0 Introduction .............................................................15
2.1 Programming Commands .........................................16
2.2 Programming Examples ...........................................21
2.3 Configuration Command String................................22
2.4 Printing Bar Codes...................................................23
2.5 Memory Cartridges (Modules)..................................24
♦♦ Maintenance
3.0 Introduction .............................................................25
3.1 Cleaning the Printhead..............................................25
3.2 Media Width Adjustment..........................................26
3.3 Fine Printhead Adjustment........................................27
3.4 Printhead Replacement.............................................28
(continued)
ii
Appendix A
ASCII Control Code Chart ..............................................A-1
Appendix B
Available Fonts and Bar Codes........................................B-1
Appendix C
Error Codes.....................................................................C-1
Appendix D
Warranty Information......................................................D-1
Getting Started 1
♦♦ Getting Started
Figure 1-1 Printer Overview
1.0 Introduction
The BradyprinterTHT Model 1024, hereafter referred to as 'the Printer',
incorporates high performance/low cost thermal transfer label printing
capabilities. The combination of powerful capabilities, compact design,
and easy to use features make this Printer truly unique.
1.1 Unpacking and Inspection
Inspect the shipping container(s), if damage is evident, contact the carrier
to specify the nature and extent of the damage.
The Printer is packed in Corrupadrecycled packaging and is enclosed
in a plastic bag to reduce the chance of moisture damage during shipment.
Remove the Printer from the plastic bag before use.
Along with this manual, the shipping container(s) should include the
following standard items:
•Label printer
•External power supply
•Special or additional items purchased.
2Getting Started
1.2 Printer Specifications
Mechanical
Width 8.8" (22.35 cm)
Depth 10.1" (25.65 cm)
Height 6.2" (15.75 cm)
Weight 7 lbs. (15.4 kg)
Operating Temperature 40°F to 100°F (4°C to 38°C)
Printer Specifications
Print Type Thermal Transfer
Print Speed 1, 1.5, and 2" per second
Resolution 203 dpi (8 dots/mm)
Tear Bar Tear up
DRAM Memory 512 kb
EPROM Memory 512 kb
Media/Ribbon
Media Types Roll-Fed, Die-Cut, Continuous, Fan-Fold
Max. Media Width 4.65" (118 mm)
Max. Print Width 4.1" (104 mm)
Min. Print Width 1" (25 mm)
Max. Print Length 12" (305 mm) with standard RAM
Min. Print Length .375" (.95 cm)
.5" (1.27 cm) w/ Present Sensor
Media Thickness .0025" - .01" (.0635 mm - .254 mm)
Ribbon Matched to Media; approx. 4330"(110m)
long
1.5" O.D. on .5" core
Getting Started 3
Communications
Interface RS-232 (DB-9), and Centronics Parallel
Baud Speed 1200 to 19200 bps
Handshaking Xon/Off, CTS, DTR
Parity Even, Odd, or None
Stop Bits 1 or 2
Data Bits 7 or 8
Electrical
External Power Supply Nominal 115 or 230 VAC IN/ 19 VAC OUT
Fonts
10 Resident Styles
Resident Fonts Expandable to 8x
Reverse Image
Rotated 0, 90, 180, 270 degrees
Available Bar Codes
Code 39, Ext Code 39, Code 93, Ext Code 93, Code 128 UCC, Code 128
A, B & C, Codabar, Interleaved 2 of 5, UPC-A, UPC-E, UPC Ship C
Code, EAN-13, EAN-8, EAN 128, POSTNET, MaxiCode, PDF417
Options
Present Sensor
Memory Cartridges
External Cutter
DRAM Memory, (Expandable to 1MB)
Wall Mount
External Battery
Time/Date
External Media Supply
4Getting Started
1.3 Connecting Power
The Printer is powered from an External Power Supply. The supply
connects to the Printer as shown below. Power supplies are available for
115 and 230 AC voltages. Ensure that the power supply shipped with the
Printer matches your electric service.
Caution!
Connect power supply to Printer before plugging into AC
outlet.
Figure 1-2 External Power Supply
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Impresora de Brady
Brady
Brady IP Printer series Manual de usuario
Brady
Brady 2024 Manual de usuario
Brady
Brady touch print Manual de usuario
Brady
Brady BradyPrinter M611 Manual de usuario
Brady
Brady BBP81 Manual de usuario
Brady
Brady THT-BP Precision Manual de usuario
Brady
Brady BP-PR 300 PLUS Series Manual de usuario
Brady
Brady BP-PR PLUS Series Manual
Brady
Brady BBP12 Manual de usuario
Brady
Brady PAM 3000 Manual de usuario
Brady
Brady LS2000 Manual de usuario
Brady
Brady BradyPrinter S3700 Manual de usuario
Brady
Brady BradyPrinter M611 Manual de usuario
Brady
Brady PAM 3600 Manual de usuario
Brady
Brady IP Printer series Manual de usuario
Brady
Brady IP300 Manual de usuario
Brady
Brady BP-1244 Manual de usuario
Brady
Brady BBP 33 Manual de usuario
Brady
Brady TLS2200 Manual de usuario
Brady
Brady BBP81 Manual de usuario
