B+K precision 9130B Manual de usuario

9130B Series

Triple Output Programmable DC Power Supplies

Models: 9130B, 9131B, 9132B

USER MANUAL

www.GlobalTestSupply.com

Quality BK Precision Products Online at: sales@GlobalTestSupply.com

Safety Summary

The following safety precautions apply to both operatingand maintenancepersonnel and must

be followed during allphases of operation, service, and repair of this instrument.

Before applying power to this instrument:

•Read and understand the safety and operational information in this manual.

•Apply all the listed safety precautions.

•Verify that the voltage selector at the line power cord input is set to the correct line

voltage. Operating the instrument at an incorrect line voltage willvoid the warranty.

•Make all connections to the instrument before applying power.

•Do notoperate theinstrument in ways not specified bythis manual orby B&K Precision.

Failure to comply with these precautions or with warnings elsewhere in this manual violatesthe

safety standards of design, manufacture, and intended use of the instrument. B&K Precision

assumes no liability for a customer’s failure to comply with these requirements.

Category rating

The IEC61010 standard defines safety category ratings that specify the amount of electrical

energy available and the voltage impulses that may occur on electrical conductors associated

with these category ratings. The category rating isa Roman numeral of I, II, III, or IV. This rating

is also accompanied by a maximum voltage of the circuit to be tested, which defines the voltage

impulses expected and required insulation clearances. These categories are:

Category I (CAT I): Measurement instruments whose measurement inputs are not intended to

be connectedto the mains supply. The voltages in the environment are typically derived from a

limited-energy transformer or a battery.

Category II (CAT II): Measurement instruments whose measurement inputs are meant to be

connected to the mains supply at a standard wall outlet or similar sources. Example

measurement environments are portable tools and household appliances.

Category III (CAT III): Measurement instruments whose measurement inputs are meant to be

connected to the mains installation of a building. Examples are measurements inside a

building's circuit breaker panel or the wiring of permanently-installed motors.

Category IV (CAT IV): Measurement instruments whose measurement inputs are meant to be

connected to the primary power entering a building or other outdoor wiring.

Do notuse this instrument in an electrical environment with ahigher category ratingthan what

www.GlobalTestSupply.com

Quality BK Precision Products Online at: sales@GlobalTestSupply.com

iii

is specified in this manual for this instrument.

You must ensure that each accessory you use with this instrument has a category rating equal to

or higher than the instrument's category rating tomaintain the instrument's category rating.

Failure to do so will lower the category rating of the measuring system.

Electrical Power

This instrument is intended to be powered from a CATEGORY II mains power environment. The

mains power should be 120 V RMS or 240 V RMS. Use onlythe power cord supplied with the

instrument and ensure it is appropriate for your country of use.

Ground the Instrument

To minimize shock hazard, the instrument chassis and cabinet must be connected to an

electrical safety ground. This instrument is grounded through the ground conductor of the

supplied, three-conductor AC line power cable. The power cable must be plugged into an

approved three-conductor electrical outlet.The power jack and mating plug of the power cable

meet IEC safety standards.

Do not alter or defeat the ground connection. Without the safety ground connection, all

accessible conductive parts (including control knobs) may provide an electric shock. Failure to

use a properly-grounded approved outlet and the recommended three-conductor AC line power

cable may result in injury or death.

Unless otherwise stated, a ground connection on the instrument'sfront or rear panel is for a

reference of potential only and is not to be used as a safety ground.

Do not operate in an explosive or flammable atmosphere

Do not operate the instrument in the presence of flammable gases or vapors, fumes, or finely-

divided particulates.

The instrument is designed to be used in office-type indoor environments. Do not operate the

instrument

•In the presence of noxious, corrosive, or flammable fumes, gases, vapors, chemicals, or

finely-divided particulates.

•In relative humidity conditions outside the instrument's specifications.

•In environments where there is a danger of any liquidbeingspilled on theinstrument or

www.GlobalTestSupply.com

Quality BK Precision Products Online at: sales@GlobalTestSupply.com

where any liquid can condense on the instrument.

•In air temperatures exceeding the specified operating temperatures.

•In atmospheric pressures outside the specified altitude limits or where the surrounding

gas is not air.

•In environments with restricted cooling air flow, even if the airtemperatures are within

specifications.

•In direct sunlight.

This instrument is intended to be used in an indoor pollution degree 2 environment. The

operating temperature range is 0 °C to 40 °C and the operating humidity range is up to 80%

relative humidity with no condensation allowed.

Measurements madebythis instrument may beoutside specifications if the instrument is used

in non-office-type environments. Such environments may include rapid temperature or

humidity changes, sunlight, vibration and/or mechanical shocks, acoustic noise, electrical noise,

strong electric fields, or strong magnetic fields.

Do not operate instrument if damaged

If the instrument is damaged, appearsto be damaged, or if any liquid, chemical, or other

material gets on or inside the instrument, remove the instrument'spower cord, remove the

instrument from service, label it asnot to be operated,and return the instrument to B&K

Precision for repair. Notify B&K Precision of the nature of any contamination of the instrument.

Clean the instrument only as instructed

Do not clean the instrument, its switches,or its terminals with contact cleaners, abrasives,

lubricants, solvents,acids/bases, or other such chemicals. Clean the instrument only with a

clean dry lint-free cloth or as instructed in this manual.

Not for critical applications

This instrument is not authorized forusein contact withthe humanbody or foruse asa

component in a life-support device or system.

Do not touch live circuits

Instrument covers must not beremoved by operatingpersonnel. Component replacement and

internal adjustments must be madeby qualified service-trained maintenance personnel who

are aware of the hazards involved when the instrument's covers and shields are removed.

Undercertain conditions, even with thepower cordremoved, dangerous voltages may exist

www.GlobalTestSupply.com

Quality BK Precision Products Online at: sales@GlobalTestSupply.com

when the covers are removed. To avoid injuries, always disconnect the power cord from the

instrument, disconnect all other connections (for example, test leads, computer interface

cables, etc.), discharge all circuits, and verifythere are no hazardous voltages present on any

conductors by measurements with a properly-operating voltage-sensingdevice before touching

any internal parts. Verify the voltage-sensing device is working properly before and after making

the measurements by testing with known-operating voltage sources and test for both DC and AC

voltages. Do not attempt any service or adjustment unless another person capable of rendering

first aid and resuscitation is present.

Do not insert any object into an instrument's ventilation openings or other openings.

Hazardous voltages maybe present in unexpected locations in circuitry being tested when a

fault condition in the circuit exists.

Fuse replacement

Fuse replacement must be done by qualified service-trained maintenancepersonnel who are

aware of the instrument's fuse requirements and safe replacement procedures. Disconnect the

instrument from the power line before replacing fuses. Replace fuses only with new fuses of the

fuse types, voltage ratings, and current ratings specified in this manual or on the back of the

instrument. Failure to do so may damage the instrument, lead to a safety hazard, or cause a fire.

Failure to use the specified fuses will void the warranty.

Servicing

Do not substitute parts that are not approved byB&K Precision or modify this instrument.

Return theinstrument to B&KPrecision for service and repairto ensurethat safetyand

performance features are maintained.

Cooling fans

This instrument contains one or more cooling fans. For continued safe operation of the

instrument, theair inletand exhaust openings for these fans must not be blocked nor must

accumulated dust or other debris be allowed to reduce air flow. Maintain at least 25 mm

clearance around the sides of the instrument that contain air inlet and exhaust ports. If

mounted in a rack, position power devices in the rack above the instrument to minimize

instrument heating while rack mounted. Do not continue tooperate the instrument if you

cannot verify the fan is operating (note some fans may have intermittent duty cycles). Do not

insert any object into the fan'sinlet or outlet.

www.GlobalTestSupply.com

Quality BK Precision Products Online at: sales@GlobalTestSupply.com

Use correctly sized wires

To connect a load to the power supply, use a wire diameter large enough to handle the

maximum continuous output short-circuit current of the power supply without the wire

overheating.

For continued safe use of the instrument

•Do not place heavy objects on the instrument.

•Do not obstruct cooling air flow to the instrument.

•Do not placea hot soldering iron on the instrument.

•Do not pullthe instrument with the power cord, connected probe, or connected test

lead.

•Do not move the instrument when a probe is connected to a circuit being tested

www.GlobalTestSupply.com

Quality BK Precision Products Online at: sales@GlobalTestSupply.com

vii

Compliance Statements

Disposal of Old Electrical & Electronic Equipment (Applicable in the European

Union and other European countries with separate collection systems)

This product is subject to Directive 2002/96/EC of the European

Parliament and the Council of the European Union on waste electrical

and electronic equipment (WEEE), and in jurisdictions adopting that

Directive, is marked as being put on the market after August 13, 2005,

and should not be disposed of as unsorted municipal waste. Please

utilize your local WEEE collection facilitiesin the disposition of this

product and otherwise observe all applicable requirements.

www.GlobalTestSupply.com

Quality BK Precision Products Online at: sales@GlobalTestSupply.com

viii

CE Declaration of Conformity

This instrument meets the requirements of 2006/95/EC Low Voltage Directive and 2004/108/EC

Electromagnetic Compatibility Directive with the following standards.

Low Voltage Directive

-EN61010-1: 2001

EMC Directive

-EN 61000-3-2: 2006

-EN 61000-3-3: 1995+A1: 2001+A2: 2005

-EN 61000-4-2 / -3 / -4 / -5 / -6 / -11

-EN 61326-1: 2006

www.GlobalTestSupply.com

Quality BK Precision Products Online at: sales@GlobalTestSupply.com

Safety Symbols

Refer to the user manual for warning information

to avoid hazard or personal injury and prevent

damage to instrument.

Electric Shock hazard

( )

On (Supply). This is the AC mains

connect/disconnect switch on the front of the

instrument.

( )

Off (Supply). This is the AC mains

connect/disconnect switch on the front of the

instrument.

Direct current

Alternating current

Fuse Symbol

Chassis (earth ground) symbol

Ground terminal

Protective earth ground

CAUTION indicatesa hazardous situation which, if

not avoided, will result in minor or moderate injury

WARNING indicates a hazardous situation which, if

not avoided, could result in death or serious injury

DANGER indicates a hazardous situation which, if

not avoided, will result in death or serious injury.

www.GlobalTestSupply.com

Quality BK Precision Products Online at: sales@GlobalTestSupply.com

Table of Contents

Compliance Statements.............................................................................................................vii

Safety Symbols............................................................................................................................ix

1General Information.....................................................................................1

1.1 Product Overview.............................................................................................................1

1.2 Package Contents.............................................................................................................1

1.3 Product Dimensions.........................................................................................................2

1.4 Rackmount Installation.....................................................................................................3

1.5 Front Panel Overview.......................................................................................................5

1.6 Rear Panel Overview........................................................................................................6

1.7 Keypad Overview..............................................................................................................7

1.8 Display Overview..............................................................................................................8

2Getting Started.............................................................................................9

2.1 Input Power and Fuse Requirements...............................................................................9

2.2 Fuse Requirements.........................................................................................................10

2.3 Line Voltage Selection.................................................................................................... 10

2.4 Output Connections....................................................................................................... 12

2.5 Carrying handle Adjustment ..........................................................................................13

2.6 Preliminary Check...........................................................................................................14

3Front Panel Operation................................................................................16

3.1 Check Model and Firmware Version ..............................................................................16

3.2 Output Control...............................................................................................................16

3.3 Meter Mode...................................................................................................................17

3.4 Setting Voltage and Current........................................................................................... 17

3.5 Over Voltage Protection (OVP).......................................................................................18

3.6 Save/Recall Instrument Settings.....................................................................................18

3.7 Key Lock..........................................................................................................................19

3.8 Output Check..................................................................................................................19

4Menu Access and Options ..........................................................................21

4.1 How to Access the Menu................................................................................................21

4.2 Menu Options.................................................................................................................21

www.GlobalTestSupply.com

Quality BK Precision Products Online at: sales@GlobalTestSupply.com

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Fuente de alimentación de B+K precision

B+K precision

B+K precision 9120A Manual de usuario

B+K precision

B+K precision 9130C Series Manual de usuario

B+K precision

B+K precision VSP6020 Manual de usuario

B+K precision

B+K precision 1601 Manual de usuario

B+K precision

B+K precision 1698 Manual de usuario

B+K precision

B+K precision 1785B Manual de usuario

B+K precision

B+K precision 1790 Manual de usuario

B+K precision

B+K precision 1743B Manual de usuario

B+K precision

B+K precision 1747 Manual de usuario

B+K precision

B+K precision 1620A Manual de usuario

B+K precision

B+K precision 9100 Series Manual de usuario

B+K precision

B+K precision 1653A Manual de usuario

B+K precision

B+K precision 1900B Manual de usuario

B+K precision

B+K precision 9140 Series Manual de usuario

B+K precision

B+K precision MR Series Manual de usuario

B+K precision

B+K precision 1680 Manual de usuario

B+K precision

B+K precision 1680 Manual de usuario

B+K precision

B+K precision BK 1692 Manual de usuario

B+K precision

B+K precision 9140 Series Manual de usuario

B+K precision

B+K precision 9130 Manual de usuario

B+K precision

B+K precision 1688A Manual de usuario

B+K precision

B+K precision 1680 Manual de usuario

B+K precision

B+K precision 1672 Manual de usuario

B+K precision

B+K precision 9115/B Manual de usuario

Manuales populares de Fuente de alimentación de otras marcas

Monacor

Monacor PS-12CCD Manual de usuario

VOLTIMA

VOLTIMA MagicBox 15 Manual de usuario

Agilent Technologies

Agilent Technologies 6032A Manual de usuario

Miller

Miller Auto Deltaweld 452 Manual de usuario

BCP

BCP PUOUBK Hoja de instrucciones

HC 2210 Manual de usuario

Puls

Puls CT5.241 Manual de usuario

OCZ

OCZ ZX1250W Manual de usuario

iseg

iseg ECH 238 Manual de usuario

Power

Power XXL A Series Manual de usuario

Agilent Technologies

Agilent Technologies 6631B Manual de usuario

Renogy

Renogy PHOENIX 300 Manual de usuario

HP 6200B Manual de servicio

Epson

Epson Stylus Scan 2500 Manual de funcionamiento

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manual de usuario

Puls

Puls MiniLine ML50.100 Manual de usuario

Puls

Puls AS-Interface SLA4.100 Manual de usuario

Kenwood

Kenwood PS-60 Manual de usuario