B+K precision 4060B Series Manual del propietario

Contents

1 About Commands & Queries 3

1.1 How They are Listed 3

1.2 How They are Described 3

1.3 When can they be used? 3

1.4 Command Notation 3

2 Common Command Introduction 4

2.1 *IDN? 5

2.2 *OPC 6

2.3 *CLS 6

2.4 *ESE 6

2.5 *ESR 6

2.6 RST 7

2.7 SRE 7

2.8 *STB? 7

2.9 *TST? 7

2.10 WAI 8

2.11 Comm_Header Command 8

2.12 Output Command 8

2.13 Basic Wave Command 9

2.13.1 Paramters 9

2.14 Modulate Wave Command 11

2.14.1 ParamtersTable 11

2.15 Sweep Wave Command 13

2.15.1 Paramters 14

2.16 Burst Wave Command 15

2.16.1 Paramters 16

2.17 Parameter Copy Command 17

2.18 Arbitrary Wave Command 17

2.18.1 Notes: 18

2.19 Sync Command 18

2.20 Number Format Command 18

2.21 Language Command 19

2.22 Conguration Command 19

2.23 Buzzer Command 19

2.24 Screen Save Command 20

2.25 Clock Source Command 20

2.26 Frequency Counter Command 20

2.27 Invert Command 21

2.28 Coupling Command 21

2.29 Voltage Overload Command 22

2.30 Store List Command 22

2.31 Arbitrary Wave Data Command 23

2.32 Virtual Key Command 24

2.33 IP Command 24

2.34 Subnet Mask Command 25

2.35 Gateway Command 25

2.36 Sampling Rate Command 25

2.37 Harmonic Command 26

2.38 Waveform Combining Command 26

3 LIMITED THREE-YEAR WARRANTY 27

4 Service Information 28

About Commands & Queries

This section lists and describes the remote control commands and queries recognized by the instrument. All commands

and queries can be executed in either local or remote state.

The description for each command or query, with syntax and other information, begins on a new page. The name

(header) is given in both long and short form, and the subject is indicated as a command or query or both. Queries

perform actions such as obtaining information, and are recognized by the question mark (?) following the header.

1.1 How They are Listed

The descriptions are listed in alphabetical order according to their short form.

1.2 How They are Described

In the descriptions themselves, a brief explanation of the function performed is given. This is followed by a presentation

of the formal syntax, with the header given in Upper-and-Lower-Case characters and the short form derived from it in

ALL UPPER-CASE characters. Where applicable, the syntax of the query is given with the format of its response.

1.3 When can they be used?

The commands and queries listed here can be used for 4060B Series arbitrary/function waveform generators.

1.4 Command Notation

The following notation is used in the commands:

< > Angular brackets enclose words that are used

placeholders, of which there are two types: the header path

and the data parameter of a command.

:= A colon followed by an equals sign separates a placeholder

from the description of the type and range of values that

may be used in a command instead of the placeholder.

Braces enclose a list of choices, one of which one must be made.

[ ] Square brackets enclose optional items.

… An ellipsis indicates that the items both to its left and right

may be repeated a number of times.

Common Command Introduction

IEEE standard denes the common commands used for querying the basic information of the instrument or executing

basic operations. These commands usually start with "*" and the length of the keywords of the command is usually 3

characters.

Short Long Form Subsystem What Command/Query does

*IDN *IDN SYSTEM Gets identication from device.

*OPC *OPC SYSTEM Gets or sets the OPC bit (0) in the Event Status Register (ESR).

*CLS *CLS SYSTEM Clears all the status data registers.

*ESE *ESE SYSTEM Sets or gets the Standard Event Status Enable register (ESE).

*ESR *ESR SYSTEM Reads and clears the contents of the Event Status Register (ESR).

*RST *RST SYSTEM Initiates a device reset.

*SRE *SRE SYSTEM Sets the Service Request Enable register (SRE).

*STB *STB SYSTEM Gets the contents of the IEEE 488.2 dened status register.

*TST *TST SYSTEM Performs an internal self-test.

*WAI *WAI SYSTEM Wait to continue command.

CHDR COMM_HEADER SIGNAL Sets or gets the command returned format OUTP OUTPUT SIGNAL Sets

or gets output state.

BSWV BASIC_WAVE SIGNAL Sets or gets basic wave parameters.

MDWV MODULATEWAVE SIGNAL Sets or gets modulation parameters.

SWWV SWEEPWAVE SIGNAL Sets or gets sweep parameters.

BTWV BURSTWAVE SIGNAL Sets or gets burst parameters.

PACP PARACOPY SIGNAL Copies parameters from one channel to the other.

ARWV ARBWAVE DATA Changes arbitrary wave type.

SYNC SYNC SIGNAL Sets or gets synchronization signal.

NBFM NUMBER_FORMAT SYSTEM Sets or gets data format.

LAGG LANGUAGE SYSTEM Sets or gets language. SCFG SYS_CFG SYSTEM Sets or gets the

power-on system setting way.

BUZZ BUZZER SYSTEM Sets or gets buzzer state.

SCSV SCREEN_SAVE SYSTEM Sets or gets screen save state.

Common Command Introduction 5

Short Long Form Subsystem What Command/Query does

ROSC ROSCILLATOR SIGNAL Sets or gets state of clock source.

FCNT FREQCOUNTER SIGNAL Sets or gets frequency counter parameters.

INVT INVERT SIGNAL Sets or gets polarity of current channel.

COUP COUPLING SIGNAL Sets or gets coupling parameters.

VOLTPRT VOLTPRT SYSTEM Sets or gets state of over-voltage protection.

STL STORELIST SIGNAL Lists all stored waveforms.

WVDT WVDT SIGNAL Sets and gets arbitrary wave data.

VKEY VIRTUALKEY SYSTEM Sets the virtual keys.

SYST:COMM:

LAN:IPAD

SYSTEM:

COMMUNICATE:

LAN:IPADDRESS

SYSTEM The Command can set and get system IP address.

SYST:COMM:

LAN:SMAS

SYSTEM:

COMMUNICATE:

LAN:SMASK

SYSTEM The Command can set and get system subnet mask.

SYST:COMM:

LAN:GAT

SYSTEM:

COMMUNICATE:

LAN:GATEWAY

SYSTEM The Command can set and get system Gateway.

SRATE SAMPLERATE SIGNAL Sets or gets sampling rate. You can only use it in TrueArb mode

HARM HARMonic SIGNAL Sets or gets harmonic information.

CMBN COMBINE SIGNAL Sets or gets wave combine information.

2.1 *IDN?

Description The *IDN? query causes the instrument to identify itself. The response comprises manufacturer,

model, serial number, software version and rmware version.

Query Format *IDN?

Response Format *IDN, <device id>,<model>,<serial number>, <software version>,

<hardware version>.

<device id>=“BK” is used to identify instrument.

<model>= A model identier less than 14 characters will contain the model number.

<serial number>:Each product has its own number, the serial number can labeled

product uniqueness.

<software version>= A serial numbers about software version.

<hardware version>=The hardware level eld, should contain information about all separately

revisable subsystems. This information can be contained in single or multiple revision codes.

Example *IDN?

Returns:

*IDN BK, 4062B, 573J19100, 2.01.01.35R3B2

value2: Hardware version. value3:

Hardware subversion. value4:

FPGA version.

value5: CPLD version.

Common Command Introduction 6

2.2 *OPC

Description The *OPC (Operation Complete) command sets the OPC bit (bit 0) in the standard Event Sta-

tus Register (ESR). This command has no other eect on the operation of the device because

the instrument starts parsing a command or query only after it has completely processed the pre-

vious command or query. The *OPC? query always responds with the ASCII character 1 because

the device only responds to the query when the previous command has been entirely executed.

COMMAND SYNTAX *OPC

Query Syntax *OPC?

Response Format *OPC 1

2.3 *CLS

Description The *CLS command clears all the status data registers.

Command Syntax *CLS

Example The following command causes all the status data registers to be cleared: *CLS

2.4 *ESE

Description The *ESE command sets the Standard Event Status Enable register (ESE). This command al-

lows one or more events in the ESR register to be reected in the ESB summary message bit (bit

5) of the STB register. The *ESE? query reads the contents of the ESE register.

Command Syntax *ESE <value>

<value> = 0 to 255.

Query Format *ESE?

Query Response *ESE <value>

Example The following instruction allows the ESB bit to be set if a user request (URQ bit 6, i.e. decimal

64) and/or a device dependent error (DDE bit 3, i.e. decimal 8) occurs. Summing these values

yields the ESE register mask 64+8=72.

*ESE?

Return:

*ESE 72

2.5 *ESR

Description The *ESR? query reads and clears the contents of the Event Status Register (ESR). The response

represents the sum of the binary values of the register bits 0 to 7.

Query Format *ESR?

Query Response *ESR <value>

<value> = 0 to 255

Example The following instruction reads and clears the content of the ESR register

*ESR?

Return:

*ESR 0

Related Commands *CLS, *ESE

Common Command Introduction 7

2.6 RST

Description The *RST command initiates a device reset. The *RST recalls the default setup.

Command Syntax *RST

Example This example resets the signal generator: *RST

2.7 SRE

Description The *SRE command sets the Service Request Enable register (SRE). This command allows the

user to specify which summary message bit(s) in the STB register will generate a service request.

A summary message bit is enabled by writing a ‘1’ into the corresponding bit location. Conversely,

writing a ‘0’ into a given bit location prevents the associated event from generating a service re-

quest (SRQ). Clearing the SRE register disables SRQ interrupts.

The *SRE? query returns a value that, when converted to a binary number represents the bit set-

tings of the SRE register. Note that bit 6 (MSS) cannot be set and it’s returned value is always

zero.

Command Syntax *SRE <value>

<value> = 0 to 255

Query Format *SRE?

Query Response *SRE <value>

Example The following instruction allows a SRQ to be generated as soon as the MAV summary bit (bit

4, i.e. decimal 16) or the INB summary bit (bit 0, i.e. decimal 1) in the STB register, or both

are set. Summing these two values yields the SRE mask 16+1 = 17.

*SRE?

Return:

*SRE 17

2.8 *STB?

Description The *STB? query reads the contents of the 488.2 dened status register (STB), and the Mas-

ter Summary Status (MSS). The response represents the values of bits 0 to 5 and 7 of the Sta-

tus Byte register and the MSS summary message.

The response to a *STB? query is identical to the response of a serial poll except that the MSS

summary message appears in bit 6 in place of the RQS message.

Query Syntax *STB?

Query Response *STB <value>

<value> = 0 to 255

Example The following reads the status byte register:

*STB?

Return:

*STB 0

Related Commands *CLS, *SRE

2.9 *TST?

Description The *TST? query performs an internal self-test and the response indicates whether the self-test

has detected any errors. The self-test includes testing the hardware of all channels. Hardware

Common Command Introduction 8

failures are identied by a unique binary code in the returned <status> number. A “0” response

indicates that no failures occurred.

Query Format *TST?

Query Response *TST <status>

<status> = 0 self-test successful

Example The following causes a self-test to be performed:

TST?

Return(if no failure):

*TST 0

Related Commands *CAL

2.10 WAI

Description The *WAI (WAIT to continue) command, requires by the IEEE 488.2 standard, has no eect on

the instrument, as the signal generator only starts processing a command when the previous com-

mand has been entirely executed.

Command Syntax *WAI

Related Commands *OPC

2.11 Comm_Header Command

Description This command is used to change the query command returned format. “SHORT” parameter re-

turns short format. “LONG” parameter returns long format. “OFF” returns nothing.

Command Syntax Comm_HeaDeR <parameter>

<parameter>={SHORT,LONG,OFF}

Query Format Comm_HeaDeR?

Query Response chdr <parameter>

Example Set query command format to long. CHDR LONG Read query command format.

CHDR?

Return:

COMM_HEADER LONG

2.12 Output Command

Description Enable or disable the output of the [Output] connector at the front panel corresponding to the

channel. The query returns “ON” or “OFF” and “LOAD”, “PLRT” parameters.

Command Syntax <channel>:OUTPut <parameter>

<channel>={C1, C2}

<parameter >={a parameter from the table below}

< load>={please see the note below.}

Parameters Value Description

ON — Turn on

OFF — Turn o

LOAD <load> value of load(defaultunite is ohm)

PLRT <NOR,INVT> value of polarity parameter

Common Command Introduction 9

Query Format <channel>:OUTPut?

Query Response <channel>:OUTP <load>

Example Turn on channel one.

C1:OUTP ON

Read channel one output state.

C1:OUTP?

Return:

C1:OUTP ON, LOAD, HZ, PLRT, NOR

Set the load to 50.

C1:OUTP LOAD, 50

Set the load to HZ.

C1:OUTP LOAD, HZ

Set the polarity normal.

C1:OUTP PLRT, NOR

Set the polarity inverted.

C1:OUTP PLRT, INVT

2.13 Basic Wave Command

Description Sets or gets basic wave parameters.

Command Syntax <channel>:BaSic_WaVe <parameter>

<channel>={C1, C2}

<parameter>:={a parameter from the table below}

2.13.1 Paramters

Note: if the command doesn’t set basic wave type, WVPT parameter will be set to current

wave type.

where:

<type>={SINE, SQUARE, RAMP, PULSE, NOISE, ARB ,DC}

<frequency>={Default unit is "Hz". Value depends on the model.}

<amplitude>={Default unit is "V". Value depends on the model.}

<oset>={Default unit is "V". Value depends on the model.}

<duty>={0% to 100%. Value depends on frequency.}

<symmetry> ={0% to 100%}

<phase>={0 to 360 if you set 400,it will set 40(400-360)}

< standard deviation >={Default unit is "V". Value depends on the model.}

<mean>={Default unit is "V". Value depends on the model.}

<width>={Max_width < (Max_duty * 0.01) * period and Min_width >

(Min_duty * 0.01) * period.}

<rise>={Value depends on the model.}

<fall>={Value depends on the model.}

<delay>={Unit is S. Maximal is Pulse period, minimum value is 0.}

<bandwidth switch >={ON,OFF}

<bandwidth value>={value between 20MHz and 120MHz}

Common Command Introduction 10

Parameters Value Description

WVTP <type> Type of wave

FRQ <frequency> Value of frequency. If wave type is Noise or DC,

you can’t set this parameter.

PERI <period> Value of period. If wave type is Noise or DC, you

can’t set this parameter.

AMP <amplitude> Value of amplitude. If wave type is Noise or DC,

you can’t set this parameter.

OFST <oset> Value of oset. If wave type is Noise or DC, you

can’t set this parameter.

SYM <symmetry> Value of symmetry. Only when wave type is

Ramp, you can set this parameter.

DUTY <duty> Value of duty cycle. Only when wave type is

Square and Pulse, you can set this parameter.

PHSE <phase> Value of phase. If wave type is Noise or Pulse or

DC, you can’t set this parameter.

STDEV <standard deviation > Value of Noise wave standard deviation. Only

when wave type is Noise, you can set this

parameter.

MEAN <mean> Value of Noise wave mean. Only when wave type

is Noise, you can set this parameter.

IDTH <width> Value of width. Only when wave type is Pulse,

you can set this parameter.

RISE <rise> Value of rise time. Only when wave type is Pulse,

you can set this parameter.

FALL <fall> Value of fall time. Only when wave type is Pulse,

you can set this parameter

DLY <delay> Value of delay. Only when wave type is Pulse, you

can set this parameter.

HLEV <high level> Value of high level. If wave type is Noise or DC,

you can’t set this parameter.

LLEV <low level> Value of low level. If wave type is Noise or DC,

you can’t set this parameter.

BANDSTATE <switch > <bandwidth> State of noise bandwidth switch. Only when wave

type is Noise, you can set this parameter.

BANDWIDTH <bandwidth value> Value of noise bandwidth. Only when wave type is

noise, you can set this parameter.

Query Format <channel>:BaSic_WaVe?

<channel>={C1, C2}

Query Response <channel>:BSWV<type>,<frequency>,<amplitude>,<oset>, <duty>,<symmetry>,

<phase>,<variance>,<mean>,<width>, <rise>, <fall>, <delay>.

Example Change channel one wave type to ramp.

C1:BSWV WVTP, RAMP

Change frequency of channel one to 2000 Hz.

C1:BSWV FRQ, 2000

Set amplitude of channel one to 3Vpp.

C1:BSWV AMP, 3

Read channel basic wave parameters from device.

C1:BSWV?

Return:

Otros manuales para 4060B Series

Tabla de contenidos

Otros manuales de Equipo de laboratorio de B+K precision

B+K precision

B+K precision 1823a Manual de usuario

B+K precision

B+K precision 8600 Series Manual del propietario

Manuales populares de Equipo de laboratorio de otras marcas

Qiagen

Qiagen DML 3000 Manual de usuario

Queensgate

Queensgate NANOSCAN OP400 Manual de programación

Conviron

Conviron GEN1000-GE Manual de usuario

Parr Instrument

Parr Instrument 4560 Manual de instrucciones

IKA

IKA IC control Manual de usuario

Integra

Integra DOSE IT Manual de usuario

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manual de usuario

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manual de usuario

NI PXI-5422 Manual

Collomix

Collomix Aqix Manual de usuario

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manual de usuario

Ocean Insight

Ocean Insight FLAME-NIR+ Manual de usuario

Parker

Parker ALIGN-MG-NA Manual de usuario

BD 644787 Manual de usuario

DENTAURUM

DENTAURUM Compact Megaplus Manual de usuario

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manual de usuario

VWR

VWR SAS Super IAQ Manual de usuario

illumina

illumina MiSeqDx Manual de usuario