BPE PowerDepot BPE-LFP-2.56-ID Manual de usuario
USER MANUAL
BPE PowerDepot 2.56kWh Wall
Mounted Lithium Battery
TABLE OF CONTENTS
01 SAFETY INFORMATION
General Safety
Personal Safety
Electrical Safety
Environment Safety
05PRODUCT INFORMATION
Battery Overview
Apperance
Front Panel
Dimensions
Capacity Options
Parallel Communication
Recommended Settings
12WARNINGS
12SPECIFICATIONS
01
01
02
04
05
05
06
10
10
11
11
1
1 - SAFETY INFORMATION
1.1 General Safety
Please fully read the safety precautions in this document and observe all the safety instructions
on the equipment.
The “DANGER”, “WARNING”, and “NOTICE” statements in this document do not cover all the
safety instructions. They are only supplements to the safety instructions.
In order to ensure human safety and equipment functionality, use the appropriate symbols
below to identify any potential issues with the equipment. You must fully understand and
comply with the information to avoid personal injury and property damage.
DANGER
WARNING
NOTICE
DANGER indicates a hazardous situation which must be addressed.
WARNING indicates a hazardous situation which, if not resolved
could result in damage or void the warranty.
NOTICE indicates normal operating situation which some functions
may need addressing in order to ensure optimal battery use.
Follow local laws and regulations when installing, operating or maintaining the
equipment. The safety instructions in this document are only supplements to local
laws and regulations.
1.2 Personal Safety
Personal Requirements
Personnel who plan to install or maintain battery equipment must be trained,
have understood all the necessary safety precautions and be able to perform all
operations correctly.
Only qualified professionals or trained personnel are allowed to install, operate
and maintain the equipment.
Electrical Danger Voltage exists when the battery is powered on. Only qualified
engineers are permitted to operate.
Earth Connector Earth Connection
DC Positive and
Negative Connectors Identify positive and negative connectors of DC power source.
CE mark The product meets CE certification.
WEEE Tag Battery must be disposed of appropriately.
Recycle Battery can be recycled
2
Personal Safety
»Do not install the battery in a location accessible to children or animals.
»Do not touch the battery when charging as it may be hot.
»Do not touch the battery terminals.
»Do not stand, lean or sit on the battery.
DANGER
1.3 Electrical Safety
Battery Symbols
There are some electrical symbols on the battery which relate to electrical safety.
Please make sure you have fully understood them before installation.
3
Electrical Safety
»Before installation, ensure that the equipment is intact or electric shock/fire
may occur.
»Do not connect or disconnect power cables when the battery is switched on as
this may cause electric arcs and sparks which can lead to fire or personal injury.
»Before connecting a power cable, check the positive and negative connectors
are correct.
»Do not parallel connect different types of batteries.
»Do not connect the battery with AC power directly.
»Do not connect the battery with PV wiring directly.
»Do not connect battery to a faulty or incompatible inverter or charger.
»Do not create short circuits with the external connection.
»Make sure to power-off the battery before any maintenance.
»Make sure the earth cable is connected correctly before operation.
DANGER
»Recharge the battery every six months.
»Recharge battery within 10 days after the battery is fully discharged.
»Please connect greater than or equal to two batteries when maximum charge
current is more than 50A.
»Make sure the battery cables are installed correctly.
»Use a meter to ensure there is no voltage between positive and negative
terminals after the battery is switched off during installation or maintenance.
WARNING
4
»Please use appropriate insulated tools for install and maintenance.
»Please make sure all batteries are switched off when connected in parallel.
»Please check the LED light sequence when the battery is switched on.
»Please make sure the BMS communication cable is connected correctly between
the battery and inverter.
»Please make sure ADDS dip switch settings are correct for single or multiple
batteries.
»Please check the inverter alarm or SOC reading to ensure there is BMS
communication with inverter.
NOTICE
1.4 Environmental Safety
»Ensure that the equipment is installed in a dry and well-ventilated environment.
»The battery installation must be away from direct sunlight and rain.
»The installation position must be away from flammable materials.
»The installation position must be away from water sources such as taps, sewer
pipes and sprinklers to prevent water seepage.
»Do not expose the equipment to flammable or explosive gases or smoke. Do
not operate the equipment in such environments.
»The operation and service life of the battery is dependent on the operating
temperature. Operate the battery at a temperature equal to or better than the
ambient temperature. The recommended operating temperature ranges from
0°C to 30°C.
WARNING
5
2 - PRODUCT INFORMATION
2.1 Battery Overview
The BPE 2.56kWh Wall Mounted battery is a lithium battery pack which
consists of long life LiFePO4 battery cells and integrated BMS. It can store
and release electric energy based on the requirements of the inverter.
Features
»LiFePO4 cell technology
»8000 cycles @ 0.5C conditions
»Maximum 1C charge and discharge capability
»Wall mounted IP54 grade protection
»Maximum 8 batteries can be connected in parallel
»Protective and active BMS allows greater reliability and control
»Fully recyclable
»Compact
2.2 Appearance
2.3 Front Panel
1. Wall mount - Please mount bracket on the wall with six M8 bolts. Then lift the
battery and attach to the bracket.
2. Wiring block - 2P (1P positive and 1P negative) power interface, printed by “+” and
“-”, front mounted wiring method, positive and negative terminals are insulated by
thermoplastic polyester (PBT) insulating sheets.
3. Switch - BMS switch, when it is turned off, the BMS can be put to sleep and the
charge and discharge MOS transistors will be turned off at the same time; normal
operation will be restored after it is turned on.
Note: Please do not turn on the system switch when the product is not in use to
avoid self-consumption of the battery power.
Version 1:CAN2.0B/RS485
4. CAN2.0B COMM to inverter - BMS supports the functionality of CAN
communication, baud rate of 500K. CAN communication interface adopts 8P8C
network cable interface. It can communicate with the inverter or CAN TEST through
CAN interface. When the battery pack is connected, RS485 communication is
connected to the data. The status and information of the battery pack can be
uploaded to PCS through CAN communication.
6
7
CAN communication interface definition:
5. RS485 COMM to parallel battery - The BMS has RS485 communication for
multiple battery pack connections and the baud rate is 19200bps.
RS485 communication interface adopts 8P8C network cable interface.
RS485 pin interface definition (RJ45-8P8C)
Version 2: RS485/RS485
6. RS485 COMM to inverter - The BMS has RS485 communication for multiple
battery pack connections and the baud rate is 9600bps. RS485
communication interface adopts 8P8C network cable interface. RS485 pin
interface definition (RJ45-8P8C)
8
7. RS485 COMM to parallel battery - The BMS has RS485 communication for
multiple battery pack connections and the baud rate is 9600bps. RS485
communication interface adopts 8P8C network cable interface.
RS485 pin interface definition (RJ45-8P8C)
System Status RUN ALM SOC Definition
On Sleeping Off Off Off Off Off Off All Off
Standby Normal On Off SOC Indicators Standby
Charging
Normal On Off SOC Indicators Flashing
OC ALM On Flashing SOC Indicators Flashing
OV ALM On Off SOC Indicators
OT ALM On Flashing SOC Indicators
Discharging
Normal Flashing Off SOC Indicators SOC Indicators
Alarm Flashing Flashing SOC Indicators
All Protections Off On Off Off Off Off Sleep Mode
UV Protections Off Off Off Off Off Off Stop Discharging
8. LED Indicators
• • • • • •
Tabla de contenidos
Otros manuales de Accesorios para cámaras de BPE
