Boss Audio Systems GT2500D Manual de usuario

1000M

Service Manual

MODEL: GT2500D

SPECIFICATIONS

Maximum power output (2 Ohms): 1500W x 1ch

RMS power Output: 900W x 1ch

Bridged Power Output: 2500W x 1ch

Frequency response: 50 - 150Hz

S/N Ratio: 100dB

Low Pass Crossover (Variable) 50Hz-150Hz

Power Source Voltage: 14.4V

Ground: Negative

External dimensions: 236(W)x55(H)x318(D)mm

2. Place the parts and wiring back in their original positions after replacement or

re-wiring. For proper circuit construction, use of insulation tubes, bonding, gaps to

PCB, etc, is involved. The wiring connection and routing to the PWB are specially

planned using clamps to keep away from heated and high voltage parts. Ensure that

they are placed back in their original positions after repair or inspection. If extended

damage is caused due to negligence during repair, the legal responsibility shall be

with the repairing company.

3. Check for safety after repair. Check that the screws, parts and wires are put back

securely in their original position after repair. Ensure for safety reasons there is no

possibility of secondary ploblems around the repaired spots. If extended damage is

caused due to negligence of repair, the legal responsibility shall be with the repairing

company.

4. Caution in removal and making wiring connection to the parts for the automobile.

Disconnect the battery terminal after turning the ignition key off. If wrong wiring

connections are made with the battery connected, a short circuit and/or fire may occur.

If extensive damage is caused due to negligence of repair, the legal responsibility

shall be with the repairing company.

5. Cautions regarding chips.

Do not reuse removed chips even when no abnormality is observed in their

appearance. Always replace them with new ones. (The chip parts include resistors,

capacitors, diodes, transistors, etc). The negative pole of tantalum capacitors is

highly susceptible to heat, so use special care when replacing them and check the

operation afterwards.

6. Cautions in handling flexible PCB

Before working with a soldering iron, make sure that the iron tip temperature is

around 270... Take care not to apply the iron tip repeatedly(more than three times)

to the same patterns. Also take care not to apply the tip with force.

7. Turn the unit OFF during disassembly and parts replacement. Recheck all work

before you apply power to the unit.

To engineers in charge of repair or inspection of

our products.

Before repair or inspection, make sure to follow the instructions so that customers

and Engineers in charge of repair or inspection can avoid suffering any risk or injury.

1. Use specified parts.

The system uses parts with special safety features against fire and voltage. Use only

parts with equivalent characteristics when replacing them. The use of unspecified

parts shall be regarded as remodeling for which we shall not be liable. The onus of

product liability (PL) shall not be our responsibility in cases where an accident or

failure is as a result of unspecified parts being used.

- 2 -

EXPLODED VIEW

- 3 -

1000M

- 4 -

PRINTED CIRCUIT BOARD - 1

- 5 -

CIRCUIT DIAGRAM 1

- 6 -

CIRCUIT DIAGRAM 2

- 7 -

PARTS LIST - 1

- 8 -

PARTS LIST - 2

- 9 -

PARTS LIST - 3

- 10 -

PARTS LIST - 4

Tabla de contenidos

Otros manuales de Amplificador de coche de Boss Audio Systems

Boss Audio Systems

Boss Audio Systems Chaos C-1000 Manual de usuario

Boss Audio Systems

Boss Audio Systems CHAOS CH650 Manual de usuario

Boss Audio Systems

Boss Audio Systems R2400D Manual de usuario

Boss Audio Systems

Boss Audio Systems Chaos C-1000 Manual de usuario

Boss Audio Systems

Boss Audio Systems Riot GT1080 Manual de usuario

Boss Audio Systems

Boss Audio Systems US140 Manual de usuario

Boss Audio Systems

Boss Audio Systems Diablo D1000.2 Manual de usuario

Boss Audio Systems

Boss Audio Systems Blade BL3KD Manual de usuario

Boss Audio Systems

Boss Audio Systems Riot GT580 Manual de usuario

Boss Audio Systems

Boss Audio Systems PH2.500 Manual de usuario

Boss Audio Systems

Boss Audio Systems ONYX NX1600.2 Manual de usuario

Boss Audio Systems

Boss Audio Systems BE1600 Manual de usuario

Boss Audio Systems

Boss Audio Systems AR4000D Manual de usuario

Boss Audio Systems

Boss Audio Systems AR1200.2 Manual de usuario

Boss Audio Systems

Boss Audio Systems Diablo D1800.5 Manual de usuario

Boss Audio Systems

Boss Audio Systems GT1180 Manual de usuario

Boss Audio Systems

Boss Audio Systems CE102 Manual de usuario

Boss Audio Systems

Boss Audio Systems CXX502 Manual de usuario

Boss Audio Systems

Boss Audio Systems Riot REV-135 Manual de usuario

Boss Audio Systems

Boss Audio Systems Havoc REV-265 Manual de usuario

Boss Audio Systems

Boss Audio Systems CHAOS CH1000 Manual de usuario

Boss Audio Systems

Boss Audio Systems Ripper RIP-495 Manual de usuario

Boss Audio Systems

Boss Audio Systems Riot GT1280 Manual de usuario

Boss Audio Systems

Boss Audio Systems Diablo D1000.2 Manual de usuario

Manuales populares de Amplificador de coche de otras marcas

Cyfre

Cyfre CHACDMA-819 Manual de usuario

MTX

MTX Thunder Marine TM904 Manual de usuario

MTX

MTX Thunder TA Super TA92001 Manual de instrucciones

Lanier

Lanier 480-0239 Instrucciones de funcionamiento y mantenimiento

Kenwood

Kenwood KAC-642 Manual de usuario

Pioneer

Pioneer GM-D8500M Manual de usuario

Jensen

Jensen XA4150 Manual de usuario

Sony

Sony XM-405EQX Marketing Specifications Manual de usuario

Audiopipe

Audiopipe AQX-660.2 Manual de usuario

Clarion

Clarion APA2001 APA2001 APA2001 Guía de inicio rápido

Sony

Sony XM-7547 Manual de usuario

Alpine

Alpine PDX11000 - Amplifier Manual de usuario

Steg

Steg Qx Mos 105.4x Manual de usuario

JL Audio

JL Audio HD900/5 Manual de usuario

Memphis

Memphis 16-MC5.700 Manual de usuario

Audiopipe

Audiopipe APSM-1150 Manual de usuario

Kenwood

Kenwood KAC-PS811D Manual de usuario

Fusion

Fusion CA-DA41400 Manual de usuario