Bosean Electronic Technology K-600 Manual de usuario

K-600

Portable Multi-gas Detector

with Built-in Pump

User Manual

Ver：BSA20180501001

Bosean Electronic Technology Co.,Ltd

ISO9001-2008

Bosean Electronic Technology Co.,Ltd www.bosean.com

Tel:86-371-86533226 Email: sales[email protected]

- 1 -

Brief Introduction

K-600 portable multi-gas detector with built-in pump is a new

intelligent gas detector, which adopts an advanced integrated

circuit, with standard intelligent level design technology, and

proprietary digital analog hybrid communication technology. The

detector is of excellent sensitivity and repeatability, which makes it

very easy to use and maintain. Thus greatly meets the safety

requirements of industrial sites with high reliability. The detector is

made of high-strength engineering plastics, compound non-slip

rubber, which is of high strength and good hand feeling. what’s

more, the detector is water-proof, dust-proof and explosion-proof.

It is widely used in petroleum, chemical, environmental, metallurgy,

refining, gas transmission and distribution, biochemical medicine,

agricultural and other industries.

1. Main features

*Gas pump sampling method and high-sensitivity sensor, with

high sensitivity and repeatability.

* 32-bit built-in MCU, high reliability and self-adaptation ability.

* Full functions, easy operation.

* CSTN colorful LCD, more intuitionistic, abundant and clear

indication.

* Compact design, easy carrying.

* High strength engineering plastics and compound anti-slippery

rubber; high strength, water-proof, dust-proof and explosion-proof.

*1200pcs data records, can be contacted with computer via

software. Can print the data records, can store data records, can

make the data analysis.

*Gas curve display.

Bosean Electronic Technology Co.,Ltd www.bosean.com

Tel:86-371-86533226 Email: sales[email protected]

- 2 -

2. Structure & Function

2.1 Appearance

2.2 Detector structure: the main shell, circuit boards, batteries,

display, sensors, chargers of the components.

2.3 Principle: Electrochemical or Catalytic or PID’s or infrared

sensor or VOC’s sensor.

3. Technical Data

Target Gas

Range

Low alarm

High alarm

Resolution

0～100%LEL

20%LEL

50%LEL

1%LEL

H2S

0～100ppm

10ppm

35ppm

1ppm

0～1000ppm

50ppm

150ppm

1ppm

0～30%vol

19.5%vol

23.5%vol

0.1%vol

Other gases needed, please contact supplier

Built-in pump gas inlet

LED

Button

Buzzer

LCD screen

Bosean Electronic Technology Co.,Ltd www.bosean.com

Tel:86-371-86533226 Email: sales[email protected]

- 3 -

Gas sampling method: Gas pump sampling

Detecting gas: Combustible gas, H2S, CO, O2

Accuracy: ≤±5% F.S.

Response Time: ≤30s

Indication: LCD displays real-time and system status;

LED, audio and vibration alert for gas leakage, fault and low

voltage, pump working state.

Working environment: -20℃～50℃,＜95%RH (no dew)

Power Source: DC3.7V Li-on battery, 3200mAh

Charging time: 6h~8h

Working time: ≥ 8h continuously (without alarming)

Gas Sensor Life: 2 years

Explosion-proof grade: Ex ib IIB T4 Gb

Protection Grade: IP65

Weight: Appr. 400g (with battery)

Dimensions: 130mm×67mm×30mm(L × W × H)

4. Operation & Function

4.1 Turn on self check and preheating process

Press the button for 4s and then release it. the LCD

screen of the detector is turned on and the welcome interface is

displayed. The detector automatically performs self-test of the

sound, light and vibration alarm signals, displays the system

information and performs the preheating countdown. The above

information can be used to confirm the integrity of the detector

performance.

4.1.1 After the detector is warmed up and

enters the power-on state, the normal detection

state of the detector is shown in Figure 1. (The

display mode varies according to the position of

the sensor, and the gas in the figure represents

methane.) Fig.1

Bosean Electronic Technology Co.,Ltd www.bosean.com

Tel:86-371-86533226 Email: sales[email protected]

- 4 -

4.2 Turn off

Under the detector is in the normal detection state, press

button, the LCD screen will prompt the user to shut down the

interface as shown in Figure 2. The user selects whether to shut

down through button. If select sure, the screen no longer

displays any information, and the detector enters Off state.

Fig. 2

4.3 Button function

Detector in the normal detection state as shown in Figure 3:

Fig. 3

Press any key to turn on the backlight (user can set the backlight

time)

Press to enter the function menu;

Press the button to turn the gas sampling pump on or off.

Press to enter the gas concentration curve display interface;

meanwhile press to view the concentration curve of different

gases.

Shut down?

BACK SURE

Bosean Electronic Technology Co.,Ltd www.bosean.com

Tel:86-371-86533226 Email: sales[email protected]

- 5 -

4.3.1when gas detector detects the gas less than the low alarm (

Mark: for oxygen, between the low alarm and high alarm value), g

as detector is under normal detecting state, no alarm at this time.

4.3.2 When the detected gas concentration is higher than low

alarm value and lower than the high alarm value (Note: When the

oxygen concentration is lower than the low alarm value), the

detector is in a low alarm state. The buzzer emits an alarm sound

of “beep,beep...”every 0.5s, and the red alarm light flashes

synchronously. At the same time, the gas concentration value on

the screen turns yellow and the backlight and vibrator are also

turned on remind of low alarm; press button to cancel the

audible alarm, but still display alarm information. The buzzer will

resume ringing until the new alarm is triggered, and the alarm light

and vibrator will resume operation. When the gas concentration

value detected by the detector returns below the low limit alarm

value, the gas concentration value turns green and the alarm

signal is automatically released. When the alarm is detected, the

detector is shown in Figure 4.

Fig.4

4.3.3 When the detected gas concentration is higher than the set

high alarm value, the detector is in the high alarm state, at this

Bosean Electronic Technology Co.,Ltd www.bosean.com

Tel:86-371-86533226 Email: sales[email protected]

- 6 -

time the buzzer emits “beep,beep,…every 0.25s”. the red

indicator light flashes synchronously, and the color of the gas

concentration value changes to red on the screen. The backlight

and the vibrator also open at the same time, indicating the high

alarm; long press the button to release the audible alarm. but

there is still an alarm message. The buzzer will resume ringing

until the new alarm is triggered, and the alarm light and vibrator

will resume operation. When the gas concentration value detected

by the detector returns below the low alarm value, the gas

concentration value turns green and the alarm signal is

automatically released. When the alarming, the detector is shown

in Figure 5.

Fig 5

4.3.4 When the detected gas concentration is higher than the test

range, the buzzer of the detector will beep normally, the LCD

screen will be on constantly, the vibrator will be normally open, and

“HHHH” will be displayed on the screen, indicating over-range. at

that time, you can press the button to release the audible

alarm.

4.3.5 Display time, gas sampling pump flag , buzzer indication

(signal when no mute is , when mute is ), the

corresponding concentration information display of different gas

Bosean Electronic Technology Co.,Ltd www.bosean.com

Tel:86-371-86533226 Email: sales[email protected]

- 7 -

types, battery power, current date.

Note: The above alarm sounds can be manually cleared by

pressing the key. After clearing, the alarm information is still

displayed normally; if the detector triggers the alarm again, the

corresponding alarm sound information can be sent again.

4.4 Use and set functions

The detector has a total of alarm record viewing function, gas

concentration curve display, setting gas parameters, calibration,

zero calibration, language setting, information viewing, time setting,

etc. in the normal detection interface, press button to enter the

function menu, as shown in Figure 6. Then press button

to enter the function selection. When the cursor moves to the

return type on the function selection interface, continue to

return to the normal monitoring interface.

Fig.6

Note: The following menus and function keys exit to return to the

monitoring interface. This operation is no longer repeated.

4.4.1 Alarm Record Gas curve display

1. Alarm record function:

Press the button in the normal detection main interface to enter

the function menu, select the , press button to enter the

Bosean Electronic Technology Co.,Ltd www.bosean.com

Tel:86-371-86533226 Email: sales[email protected]

- 8 -

alarm record interface, the record content includes the type of

alarm sensor, enter the corresponding sensor to

display the alarm value, alarm time, as shown in

Figure 7: This function can view the gas alarm

history.

Fig.7

The maximum alarm record is up to 1200 groups.

2. Curve display function:

Press in the normal detection main interface to enter the curve

display interface.

Then press button to view the gas concentration curve of each

channel sensor. Each channel sensor has a curved display. As

shown in Figure 9:

Oxygen as an example:

Fig.8

06/08

21:18

O2 20.9% Low 19.5 % High 23.5%

Description

The abscissa X axis is the time,

the current record within 10s of

the curve

The vertical axis Y is the sensor

value, data of the sensor can be

seen from the Y axis

Note: the axis and the data is green, the data curve is blue, the

low alarm line is yellow, high alarm line is red.

Bosean Electronic Technology Co.,Ltd www.bosean.com

Tel:86-371-86533226 Email: sales[email protected]

- 9 -

4.4.2 Detector menu settings

In the normal detection mode, press to enter the menu, then

press to select the shut down,setting,alarm point, alarm record

calibration zero, calibration, time setting and system reset. These

function menus can be displayed cyclically and can be selected by

cursor movement.

The menu function is as follows:

Description

Setting content

Main

interface

Press to move the cursor to the return

function, press to return to the main interface.

(The cursor moves and selects the entry according to

the above method, and will not be described later)

Shut down

Press to move the cursor to the return

function, press to enter the shutdown selection

interface.

System

Settings

Enter the system settings interface to set the detector

channel, delete alarm records, view system

information, language settings, backlight settings,

and air pump settings.

Alarm

point

Set the low and high value

Alarm

record

Alarm record information of the corresponding

channel gas

Gas Zero

Enter the zero calibration interface to zero the four

sensors.

Otros manuales de Detector de gas de Bosean Electronic Technology

Bosean Electronic Technology

Bosean Electronic Technology BH-90 Manual de usuario

Bosean Electronic Technology

Bosean Electronic Technology BH-90a Manual de usuario

Bosean Electronic Technology

Bosean Electronic Technology BH-90E Manual de usuario

Bosean Electronic Technology

Bosean Electronic Technology BH-4M Manual de usuario

Manuales populares de Detector de gas de otras marcas

Macurco

Macurco GD-6 Manual de usuario

Evikon

Evikon E2632 Manual de usuario

Critical Environment Technologies

Critical Environment Technologies CGAS-A Series Manual de usuario

MSA

MSA altair 5 Manual de usuario

DOD Technologies

DOD Technologies ChemLogic CL96 Manual de usuario

DEGA

DEGA NS III LCD Series Manual de usuario

RKI Instruments

RKI Instruments 35-3001A-08-01 Manual de usuario

PEMTECH

PEMTECH PT2008 Series Manual de usuario

Coster

Coster RGS 328 Manual de usuario

Sygonix

Sygonix 2483186 Manual de usuario

Perry

Perry 1GA 50917MET/P Manual de usuario

isweek

isweek AS8900 Manual de usuario

Oldham

Oldham OLC 10 Manual de usuario

Wizmart

Wizmart NB983 Manual de usuario

Beacon

Beacon MEGA Manual

RKI

RKI GX-6000 Manual de usuario

Dräger

Dräger PIR 7000 Manual de usuario

GDS

GDS GASMAX EC Manual de usuario