Bose 901 Manual de usuario

The Bose

901

Series VI Direct/Reflecting

Speaker

System

Owner’sGuide

November21,2001

AM195438_03_V.pdf

2 November 21, 2001 AM195438_03_V.pdf

English

WARNING:

To reduce the risk of fire or electric shock, do not expose the 901

active

equalizer to rain or moisture.

CAUTION

These CAUTION marks are located on the bottom of your 901 active equalizer:

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert

the user to the presence of uninsulated dangerous voltage within the system enclosure that

may be of sufficient magnitude to constitute a risk of electric shock.

The exclamation point within an equilateral triangle, as marked on the system, is intended to

alert the user to the presence of important operating and maintenance instructions in this

owner’s guide.

CAUTION:

To prevent electric shock, match wide blade of plug to wide slot, insert fully.

Additional safety information

See the additional instructions on the Important Safety Information page enclosed with this

owner’s guide.

Please read this owner’s guide

Please take the time to follow this owner’s guide carefully. It will help you set up and operate

your system properly, and enjoy all of its advanced features. Save your owner’s guide for

future reference.

Safety Information

CAUTION

RISK OF ELECTRICAL SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED PERSONNEL.

AVIS

RISQUE DE CHOC ÉLECTRIQUE

NE PAS OUVRIR

ATTENTION : POUR RÉDUIRE LE RISQUE DE DÉCHARGE

ÉLECTRIQUE, NE RETIREZ PAS LE COUVERCLE (OU

L’ARRIÈRE). IL NE SE TROUVE ÀL’INTÉRIEURAUCUNE

PIÈCE POUVANT ÊTRE RÉPARÉE PARL’USAGER.

S’ADRESSER À UN RÉPARATEUR COMPÉTENT.

For your records

Serial numbers are located on the bottom panel of each 901 speaker and on the back of the

active equalizer.

Loudspeaker Serial Numbers: ____________________________________________________

Active equalizer Serial Number: __________________________________________________

Dealer name: __________________________________________________________________

Dealer phone:_______________________ Purchase date: ___________________________

We suggest you keep your sales slip and warranty card together with this owner’s guide.

AM195438_03_V.pdf November 21, 2001 3

Contents

Where to find…

Contents

Where to find….............................................................................................................3

Warranty period ............................................................................................................3

Customer service..........................................................................................................3

Setting Up

Before you begin...........................................................................................................4

Unpacking the cartons..................................................................................................4

System compatibility .................................................................................................... 5

Choose the support for your speakers .........................................................................6

Choosing the location for your speakers ......................................................................6

Speaker connections .................................................................................................... 8

Equalizer connections...................................................................................................9

Testing the speakers and equalizer ............................................................................12

Using other equipment ...............................................................................................13

Using your 901®Series VI speaker system

Playing your speakers.................................................................................................14

Adjusting the sound ....................................................................................................15

Equalizer compatibility................................................................................................16

Connecting additional speakers ................................................................................. 16

Maintaining Your 901 speaker system

Cleaning your speakers ..............................................................................................17

Troubleshooting ..........................................................................................................17

Product Information

Technical information..................................................................................................18

Accessories.................................................................................................................18

Bose Corporation .....................................................................................inside back cover

Warranty period

The Bose

901 speakers and active equalizer are covered by a limited 5-year transferable

warranty. Details of the warranty are provided on the warranty card that came with your

system. Please fill out the information section on the card and mail it to Bose Corporation.

Customer service

For additional help in solving problems, contact Bose customer service. See the inside back

cover for Bose customer service offices and phone numbers.

A free booklet is available: Guide to Optional System Connections for Bose 901

Direct/

Reflecting

Speaker Systems. Ask for part number 149393.

4 November 21, 2001 AM195438_03_V.pdf

English

Setting Up

Before you begin

Thank you for purchasing the Bose

901

Series VI Direct/Reflecting

speakers. They repre-

sent the best in Bose Corporation speaker design and engineering and will give you many

years of listening pleasure.

The installation and operating principles of this system are significantly different from those of

conventional speakers. To obtain the best possible performance and avoid problems, please

take the time to read this guide.

CAUTION:

You must have a Bose 901 active equalizer for a complete 901 speaker system.

The use of 901 Series VI speakers without the 901 Series VI active equalizer will result in

improper performance. The use of graphic or parametric equalizers, instead of the Bose 901

equalizer, will result in unsatisfactory performance.

Conventional graphic and parametric equalizers may be used in addition to, but not in place

of the Bose 901 active equalizer. However, the use of such additional equalizers is not

recommended since it will not improve system performance. For adequate performance you

must use the 901 Series VI active equalizer with these speakers.

Unpacking the cartons

A complete Bose 901 Series VI speaker system consists of three matched components: two

901 Direct/Reflecting

speakers and a separate 901 Series VI active equalizer. Two cables are

included to connect the active equalizer to your receiver or amplifier. The 901 speakers and

equalizer are packed in three separate cartons. Carefully unpack your system, saving all

packing materials for possible future use.

Inspect the speakers and equalizer. If any part appears damaged, do not attempt to use the

system. Repack the speakers and equalizer in their original cartons and notify your authorized

Bose dealer immediately.

Note:

Now is a good time to record the serial numbers of each speaker and the active

equalizer. Please write them on your warranty card and in the spaces provided on page 2.

The serial numbers are located on the bottom of the 901 speakers and on the back of the

equalizer.

WARNING:

Each speaker carton weighs over 35 lb (16 kg). Use good lifting practice to

avoid injury.

WARNING:

To avoid danger of suffocation, keep the plastic bags out of the reach of

children.

Figure 1

What comes in the three

cartons:

• Two 901 speakers

• One 901 active equalizer

• Two equalizer cables

AM195438_03_V.pdf November 21, 2001 5

Setting Up

System Compatibility

Bose

901

Series VI speakers and Series VI active equalizer work with your stereo

components to produce a superb music system. The active equalizer is an integral part of

the system and may be connected in a variety of ways, depending on the components

you have. The two most common methods are described in this guide. Using different

components may require different connection methods. More information is available by

calling Bose Corporation. Ask for the free booklet, Guide to Optional System Connections

for Bose 901 Direct/Reflecting

Speaker Systems, part number 149393.

Your 901 speakers are designed to work compatibly with receivers or amplifiers rated from

10 to 450 watts per channel. In this guide, the term receiver is used to refer to an

integrated preamplifier and power amplifier (which may also contain an AM/FM tuner). The

term amplifier is used to describe configurations involving separate preamplifier and

amplifier components.

Most receivers have a TAPE MONITOR connection. The 901 active equalizer is most

commonly connected to the tape monitor connections on the receiver. If you plan to

connect a tape recorder, use the set of inputs and outputs located on the back of the 901

active equalizer marked TAPE RECORDER CONNECTIONS.

If you have recently purchased a home theater receiver, you may be considering using

your 901 speakers for the front channels. Your home theater receiver must have

accessible PRE AMP OUT/MAIN AMP IN connections for the front channels if you are to

use your 901 speakers in this way. These may also be called the ADAPTER or SIGNAL

PROCESSOR connections.

Installation steps

Follow these steps, in the order below, to install your 901 Series VI speaker system.

1. Choose the best locations and support for the 901 speakers (page 6).

2. Connect the speakers to the amplifier or receiver (page 8).

3. Connect the 901 active equalizer to the amplifier or receiver using either the TAPE

MONITOR or PRE AMP OUT/MAIN AMP IN connections (page 9).

4. Test the system to see that the audio signal is correctly processed by the active

equalizer (page 12).

6 November 21, 2001 AM195438_03_V.pdf

English

Setting Up

Choosing the location for your speakers

Choose locations for your 901

speakers that use the walls to best advantage by reflecting

sound throughout the listening room. Refer to the drawing on page 7.

Guidelines for placement

Place the speakers along the same wall (see Figure 3):

• 4 to 12 feet (1.2 – 3.6 m) apart, with the V-shaped rear of the speaker between 8 and 18

inches (20 – 45 cm) from the rear wall. Do not aim the V toward a corner.

• 18 inches (45 cm) of clear space around the sides, top, and bottom of the speakers.

• at least 2 feet (60 cm) from sound-absorbent furnishings.

• 18 to 48 inches (45 – 120 cm) from the side and rear walls.

• 18 to 36 inches (45 – 91 cm) from the floor or ceiling. Do not place the speakers exactly

halfway between floor and ceiling.

Within these guidelines, remember that the closer the speakers are placed to a reflective

surface, like a wall, the more bass is reproduced.

Choose the support for your speakers

You may place 901 speakers on a table or shelf. You may also use Bose

floor pedestals, or

suspend the speakers from your ceiling. Refer to Figure 3 on page 7.

To set the speakers on a table or shelf

Although each speaker weighs 35 lb (16 kg), a suitable shelf or table must be able to support

140 lb (64 kg). Keep an adequate distance between the speakers and the rear wall as listed

in “Guidelines for placement” above.

To stand the speakers on the floor

Use only Bose pedestals (PS-6) as floor stands. They are designed to provide the proper

support and are available through your authorized Bose dealer. Please read the pedestal

attachment instructions before making any speaker connections. Four pilot holes on the

bottom of each speaker (see Figure 2, hole set A) are pre-drilled for the purpose of anchor-

ing the speaker to the pedestal.

To suspend the speakers from the ceiling

Use these guidelines to ensure safe suspension of your 901 speakers. Three steel support

chains are recommended. We cannot specify the ceiling attachments. The type to use

depends on the type of building construction.

CAUTION:

Do not mount on surfaces that are not sturdy enough, or that have hazards

concealed behind them, such as plumbing or electrical wire. If you are unsure of your ability

to install these speakers, contact a qualified professional installer.

Note:

The speakers hang in an inverted position, with the terminal connections facing up.

Carefully rotate the Bose logo 180˚ (so it appears right side up) before hanging the speak-

ers.

Figure 2

Pedestal (A) and ceiling mount

(B) pilot holes

AM195438_03_V.pdf November 21, 2001 7

Setting Up

Hardware needed for ceiling suspension

• Screw hooks support the chains at the ceiling. They must have at least a #10 wood

thread with a shank diameter of at least

⁄

inch (4.5 mm). They should be long enough

to go through any plasterboard and still have at least one inch (25 mm) of thread left to

penetrate a wood beam. For a masonry ceiling: use only high-quality metal expansion

masonry anchors that fit the thread of the ceiling hooks.

• Chain: diameter should be at least

⁄

inch (0.135 in. or 4 mm).

• Screw eyes with S hooks attach chains to the speaker and must have at least a #10

wood thread with a shank diameter of at least

⁄

inch (4.5 mm) or larger.

• All hardware (screw hooks, chain, screw eyes, S hooks) must have a manufacturer’s

safe-load rating of 40 lb (18 kg) or more.

General notes on ceiling suspension

• Suspend the speakers 18 – 36 inches (45 – 91 cm) from the ceiling; do not mount them

flush to the ceiling.

• To ensure an accurate stereo image, the distance from the floor should be three to ten

feet (1 – 3.5 m). Be sure the speakers are no less than 18 inches (45 cm) from the floor.

Do not suspend the speakers exactly halfway between the floor and ceiling.

Note:

If the speakers are more than 10 feet (3 m) from the floor, we suggest you lengthen

the chain supporting the rear of the speaker. By doing this you will allow the rear of the

speaker, housing eight of the nine drivers, to be angled slightly downward.

Step by step procedure for ceiling suspension

1. Ceiling: Anchor at least two screw hooks into a rigid structural ceiling support (beam,

joist, or masonry anchor). Drill pilot holes into wood using a

⁄

inch drill bit (3.7 mm), if

necessary.

2. Speaker: Use the three pre-drilled pilot holes (see Figure 2 - hole set B) on the bottom of

each speaker. Use a

⁄

inch drill bit (3.7 mm) to enlarge the pilot holes to accept the #10

thread screw eyes. Drill to a depth of

⁄

inch (12 mm) in the speaker cabinet. Do not drill

completely through the cabinet.

Note:

Contact Bose

for more information on suspending speakers. See the inside back

cover for phone numbers. For details on your specific ceiling construction, consult a

qualified building contractor or professional installer.

Figure 3

Mounting guidelines

18 – 48"

(45 – 120 cm)

18 – 36" (45 – 91 cm)

4 – 12'

(1.2 – 3.6 m)

18 – 48"

(45 – 120 cm)

4 – 12'

(1.2 – 3.6 m)

18 – 36" (45 – 91 cm)

8 – 18" – (20 – 45 cm)

8 November 21, 2001 AM195438_03_V.pdf

English

Setting Up

Speaker connections

With your speakers in their chosen locations, connect them to the receiver.

Choosing the wire

It is important to use the right thickness of speaker wire. For distances of up to 30 feet (9 m),

18 gauge (.075 mm

) 2-conductor wire works well. For distances greater than 30 feet (9 m),

refer to the wire recommendations chart on page 18.

Note:

To determine if this wire is suitable for use in a wall or under a floor, check your local

building codes. You may want to contact a qualified electrical installer for this information.

Preparing the speaker wires

Examine the speaker wire. Note that it is actually a pair of insulated wires that may be gently

pulled apart. The insulation around one wire is marked with a stripe, collar, rib, groove, or

printing. Use the marked wire as positive (+) and the unmarked wire as negative (-). These

wires correspond to the positive and negative terminals on the speaker and receiver.

Note:

It may be difficult to distinguish wire markings. Inspect both wires carefully.

To prepare the ends of each wire:

1. Strip approximately

inch (12 mm) of insulation from both wires.

2. Twist the bare ends of each stranded wire, to prevent strands from touching across

terminals.

Connecting the speakers

CAUTION:

Before making any connections, turn off your receiver and unplug it from the

AC (mains) power outlet. Not doing this may result in damage to your system.

Speaker terminals are located on the bottom of each speaker. Unscrew the knurled nut on

each terminal and remove one washer. Wrap one bare wire end around the terminal post.

Then, replace the metal washer on the screw post and screw the knurled nut firmly back on.

1. Connect one wire pair to the right speaker (the one on your right as you face it).

a. Attach the marked wire at one end to the positive (+) terminal.

b. Attach the plain wire at that end to the negative (-) terminal.

2. Connect the other ends of the same wire pair to the RIGHT SPEAKER OUTPUT of your

receiver.

a. Attach the marked wire to the positive (+) terminal.

b. Attach the plain wire to the negative (-) terminal.

3. Following the steps above, connect the second pair of wires to the left speaker and to the

LEFT SPEAKER OUTPUT on the receiver.

Note:

If your receiver offers a choice of output impedances, use the terminal marked 8

Ω

8 ohms.

AM195438_03_V.pdf November 21, 2001 9

Setting Up

Checking the speaker connections

Make sure the terminal knurled nut is tightened down firmly. Any gap between the wire and

terminal can cause heat build up. Check to be sure the wires are connected positive to

positive (+ to +) and negative to negative (- to -). Make sure no loose strands of wire touch

across terminals, which can cause short circuits.

Figure 4

Connecting the speakers to the

receiver

Equalizer Connections

There are two options for connecting the equalizer. Your choice depends on the type of

receiver you own and whether you plan to use the system primarily for stereo or for home

theater enjoyment.

Stereo/non-home theater use

(tape monitor connections)

The Bose

901

active equalizer connects directly to your receiver through the tape monitor

connection. If your receiver has more than one tape connection, use the second one (TAPE 2).

To connect a tape deck, use the additional set of inputs and outputs located on the back of

the 901 active equalizer marked TAPE RECORDER CONNECTIONS.

The TAPE MONITOR switch on the front of the receiver lets you switch the equalizer in and

out of the signal path. This is important when you want to play conventional, non-equalized

speakers or headphones attached to your receiver. See Using other equipment on page 13.

Note:

If your receiver is designed for home theater use, it may not have a Tape Monitor

switch. If not, you must use a PRE AMP OUT/MAIN AMP IN connection. This may also be

called the ADAPTER or SIGNAL PROCESSOR connection. Refer to “Home theater use (PRE

AMP OUT/MAIN AMP IN)” on page 10 for instructions on how to connect for home theater

use.

1. Disconnect any external tape deck or signal processor connected to the tape monitor

connection.

2. Use the twin cable assemblies (with two connectors at each end) that are supplied with the

equalizer. Use the red connector for the right (R) channel connections and the other

connector for the left (L) channel connections.

Receiver

+ – + –

10 November 21, 2001 AM195438_03_V.pdf

English

Setting Up

3. Connect one end of a cable to the AMPLIFIER INPUT jacks on the 901

active equalizer.

a. Insert the first connector firmly into the INPUT jack marked R.

b. Insert the second connector into the INPUT jack marked L.

4. Connect the other end of the cable to the OUT or RECORD jacks on your receiver. These

jacks may be marked TO INPUT, FROM INPUT, or REC.

a. Insert the first connector into the OUT or RECORD jack marked R.

b. Insert the second connector into the OUT or RECORD jack marked L.

5. Connect the second cable from the AMPLIFIER OUTPUT jacks on the 901 active equalizer

to the IN or TAPE jacks on your receiver. These jacks may be marked PLAY, TO OUTPUT,

FROM OUTPUT, or MONITOR.

6. Plug the power cord of the 901 active equalizer into one of the switched outlets on the

receiver so that it will be powered when the receiver is switched on.

Figure 5

Connecting to the tape monitor

connection

Home theater use

(PRE AMP OUT/MAIN AMP IN)

Use these instructions:

• for stereo-only operation if your receiver does not have a TAPE MONITOR connection.

• if you are using a surround sound receiver that has a section on the back marked PRE

AMP OUT/MAIN AMP IN. The jacks may be labeled ADAPTER or SIGNAL PROCESSOR.

Note:

If your receiver does not have this PRE AMP OUT/MAIN AMP IN section, the 901

speakers will not be usable in your home theater system.

1. The PRE AMP OUT/MAIN AMP IN jacks on your receiver are usually connected by small

bars called horseshoe pins. Remove these pins. See Figure 6.

Figure 6

Removing horseshoe pins

Amplifier or Receiver

MAIN

AMP

PRE

AMP

OUT

Otros manuales para 901

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de altavoces de Bose

Bose

Bose FreeSpace 3 Manual de usuario

Bose

Bose SMART SOUNDBAR 700 Manual de usuario

Bose

Bose LIFESTYLE RoomMate Manual de usuario

Bose

Bose Soundbar 500 Manual de usuario

Bose

Bose ShowMatch DeltaQ SMAF Manual de instrucciones

Bose

Bose FreeSpace 3 Manual de usuario

Bose

Bose 901 Manual de usuario

Bose

Bose AM-25P II Manual del propietario

Bose

Bose 601 Series IV Direct/Reflecting Manual de usuario

Bose

Bose SOUNDTOUCH 300 Manual de usuario

Bose

Bose 601TM Manual de usuario

Bose

Bose 6.2 Manual de usuario

Bose

Bose SOUNDTOUCH 300 Guía de instalación

Bose

Bose Acoustimass 15 Series II Manual de usuario

Bose

Bose LIFESTYLE RoomMate Manual de usuario

Bose

Bose 2.2 Manual de usuario

Bose

Bose SOLO SOUNDBAR II Series Manual de instrucciones

Bose

Bose Panaray MA12 Manual de usuario

Bose

Bose SMART SOUNDBAR 700 Manual de usuario

Bose

Bose L1 Model II Manual de usuario

Bose

Bose Acoustimass SE-5 Manual de usuario

Bose

Bose FreeSpace DS 100SE Guía

Bose

Bose SB600 Manual de usuario

Bose

Bose Bundle Manual de usuario

Manuales populares de Sistema de altavoces de otras marcas

JVC

JVC CA-MXK5R Manual de usuario

LG NB4532B Manual de usuario

JVC

JVC CA-FSH100 Manual de usuario

5Core

5Core Pro Series Manual de usuario

EAW

EAW MQV1394e Manual de usuario

Lynx

Lynx GXR-LA10A Manual de usuario

iLive

iLive ITB066B Manual de usuario

RDX

RDX QuickStation 4 Manual de usuario

Electro-Voice

Electro-Voice S-122 Manual de usuario

Sven

Sven SPS-619 GOLD Manual de usuario

Pioneer

Pioneer CS-7070 Manual de usuario

EAW

EAW UB82e Manual de usuario

Sondpex

Sondpex Active Speaker System and Digital Music... Manual de usuario

JVC

JVC NX-PN7 Manual de usuario

Marshall Amplification

Marshall Amplification AR-DM61-BT Manual de usuario

Yamaha

Yamaha NX-A01 - Speaker Sys Manual de usuario

SE Audiotechnik

SE Audiotechnik I-LINE Manual de usuario

Gemini

Gemini WRX-843 Series Manual de usuario