Bosch MIC Series Manual de usuario

MIC Series Power Supplies

MIC Series

en Installation Manual

MIC Series Power Supplies Table of Contents | en 3

Bosch Security Systems, Inc. Installation Manual F.01U.141.598 | 1.0 | 2009.11

Table of Contents

1Safety 4

1.1 Important safety instructions 4

1.2 Safety precautions 6

1.3 Important notices 7

1.4 Customer Support and Service 14

2 Introduction 16

2.1 Parts List 16

2.2 Preparing the Power Supply Unit 17

2.3 Securing the Power Supply Unit 18

2.4 IP Rating 18

2.5 MIC Shielded Composite Cable Gland Connection 19

3 MIC Non-IR Power Supply Units 20

3.1 Printed Circuit Board Earth Link 20

3.2 Non-IR Power Supply Layout and Connections 22

3.3 Fuse Ratings 23

3.4 Installing a Non-IR Power Supply 24

3.5 Optional Cards and Kits for Non-IR MIC Cameras 29

3.6 Commissioning a MIC Series Camera with Public Address

Speakers 29

3.7 Commissioning a MIC Series Camera with Heater Option 30

4 MIC IR Power Supply Units 32

4.1 Printed Circuit Board Earth Link 33

4.2 Fuse Ratings 34

4.3 MIC IR Power Supply Layout and Connections 35

4.4 Installing a MIC IR Power Supply 36

4.5 Commissioning the IR Lamps 42

5 Technical Specifications 43

5.1 Dimensional Drawings 44

4en | Safety MIC Series Power Supplies

F.01U.141.598 | 1.0 | 2009.11 Installation Manual Bosch Security Systems, Inc.

1Safety

1.1 Important safety instructions

Read, follow, and retain for future reference all of the following

safety instructions. Heed all warnings on the unit and in the

operating instructions before operating the unit.

1. Cleaning - Unplug the unit from the outlet before cleaning.

Follow any instructions provided with the unit. Generally,

using a dry cloth for cleaning is sufficient, but a moist fluff-

free cloth or leather shammy may also be used. Do not use

liquid cleaners or aerosol cleaners.

2. Heat Sources - Do not install the unit near any heat

sources such as radiators, heaters, stoves, or other

equipment (including amplifiers) that produce heat.

3. Water - Do not use this unit near a bathtub, washbowl, or a

sink.

4. Object and liquid entry - Never push objects of any kind

into this unit through openings as they may touch

dangerous voltage points or short-out parts that could

result in a fire or electrical shock. Never spill liquid of any

kind in the unit. Do not place objects filled with liquids,

such as vases or cups, on the unit.

5. Lightning - For added protection during a lightning storm,

or when leaving this unit unattended and unused for long

periods, unplug the unit from the wall outlet and

disconnect the cable system. This will prevent damage to

the unit from lightning and power line surges.

6. Controls adjustment - Adjust only those controls specified

in the operating instructions. Improper adjustment of

other controls may cause damage to the unit. Use of

controls or adjustments, or performance of procedures

other than those specified, may result in hazardous

radiation exposure.

7. Overloading - Do not overload outlets and extension cords.

This can cause fire or electrical shock.

MIC Series Power Supplies Safety | en 5

Bosch Security Systems, Inc. Installation Manual F.01U.141.598 | 1.0 | 2009.11

8. Power supply cord and plug protection - Protect the

power supply cord and plug from foot traffic, being

pinched by items placed upon or against them at electrical

outlets, and its exit from the unit. For units intended to

operate with 230 VAC, 50 Hz, the power supply cord must

comply with the latest versions of IEC 60227. For units

intended to operate with 120 VAC, 60 Hz, the power

supply cord must comply with the latest versions of UL 62

and CSA 22.2 No.49.

9. Power disconnect - Units have power supplied to the unit

whenever the power cord is inserted into the power

source. The power cord is the main power disconnect

device for switching off the voltage for all units.

10. Servicing - Do not attempt to service this unit yourself.

Opening or removing covers may expose you to dangerous

voltage or other hazards. Refer all servicing to qualified

service personnel.

11. Damage requiring service - Unplug the unit from the main

AC power source and refer servicing to qualified service

personnel when any damage to the equipment has

occurred, such as:

– the power supply cord or plug is damaged;

– exposure to moisture, water, and/or inclement

weather (rain, snow, etc.);

– liquid has been spilled in or on the equipment;

– an object has fallen into the unit;

– unit has been dropped or the unit cabinet is damaged;

– unit exhibits a distinct change in performance;

– unit does not operate normally when the user

correctly follows the operating instructions.

12. Replacement parts - Be sure the service technician uses

replacement parts specified by the manufacturer, or that

have the same characteristics as the original parts.

Unauthorized substitutions may cause fire, electrical

shock, or other hazards.

6en | Safety MIC Series Power Supplies

F.01U.141.598 | 1.0 | 2009.11 Installation Manual Bosch Security Systems, Inc.

13. Safety check - Safety checks should be performed upon

completion of service or repairs to the unit to ensure

proper operating condition.

14. Installation - Install in accordance with the manufacturer's

instructions and in accordance with applicable local codes.

15. Attachments, changes or modifications - Only use

attachments/accessories specified by the manufacturer.

Any change or modification of the equipment, not

expressly approved by Bosch, could void the warranty or,

in the case of an authorization agreement, authority to

operate the equipment.

1.2 Safety precautions

DANGER!

High risk: This symbol indicates an imminently hazardous

situation such as “Dangerous Voltage” inside the product.

This symbol indicates the presence of non-insulated

“dangerous voltage” within the product’s enclosure that may be

of sufficient magnitude to constitute a risk of electric shock to

persons.

WARNING!

Medium risk: Indicates a potentially hazardous situation.

If not avoided, this could result in minor or moderate bodily

injury.

CAUTION!

Low risk: Indicates a potentially hazardous situation.

If not avoided, this could result in property damage or risk of

damage to the unit.

MIC Series Power Supplies Safety | en 7

Bosch Security Systems, Inc. Installation Manual F.01U.141.598 | 1.0 | 2009.11

1.3 Important notices

All-pole power switch - Incorporate an all-pole power switch,

with a contact separation of at least 3 mm in each pole, into the

electrical installation of the building.If it is needed to open the

housing for servicing and/or other activities, use this all-pole

switch as the main disconnect device for switching off the

voltage to the unit.

Coax grounding:

– Ground the cable system if connecting an outside cable

system to the unit.

– Connect outdoor equipment to the unit's inputs only after

this unit has had its grounding plug connected to a

grounded outlet or its ground terminal is properly

connected to a ground source.

– Disconnect the unit's input connectors from outdoor

equipment before disconnecting the grounding plug or

grounding terminal.

– Follow proper safety precautions such as grounding for

any outdoor device connected to this unit.

U.S.A. models only - Section 810 of the National Electrical Code,

ANSI/NFPA No.70, provides information regarding proper

grounding of the mount and supporting structure, grounding of

the coax to a discharge unit, size of grounding conductors,

location of discharge unit, connection to grounding electrodes,

and requirements for the grounding electrode.

Accessories - Do not place this unit on an unstable stand,

tripod, bracket, or mount. The unit may fall, causing serious

injury and/or serious damage to the unit. Use only with the

cart, stand, tripod, bracket, or table specified by the

manufacturer. When a cart is used, use caution and care

when moving the cart/apparatus combination to avoid injury

from tip-over. Quick stops, excessive force, or uneven

surfaces may cause the cart/unit combination to overturn.

Mount the unit per the manufacturer's instructions.

8en | Safety MIC Series Power Supplies

F.01U.141.598 | 1.0 | 2009.11 Installation Manual Bosch Security Systems, Inc.

Environmental statement - Bosch has a strong commitment

towards the environment. This unit has been designed to

respect the environment as much as possible.

Electrostatic-sensitive device - Use proper CMOS/MOS-FET

handling precautions to avoid electrostatic discharge.

NOTE: Wear required grounded wrist straps and observe proper

ESD safety precautions when handling the electrostatic-

sensitive printed circuit boards.

Fuse rating - For security protection of the device, the branch

circuit protection must be secured with a maximum fuse rating

of 16A. This must be in accordance with NEC800 (CEC Section

60).

Grounding and polarization - This unit may be equipped with a

polarized alternating current line plug (a plug with one blade

wider than the other blade). This safety feature allows the plug

to fit into the power outlet in only one way. If unable to insert

the plug fully into the outlet, contact a locally certified

electrician to replace the obsolete outlet. Do not defeat the

safety purpose of the polarized plug.

Alternately, this unit may be equipped with a 3-pole grounding

plug (a plug with a third pin for earth grounding). This safety

feature allows the plug to fit into a grounded power outlet only.

If unable to insert the plug into the outlet, contact a locally

certified electrician to replace the obsolete outlet. Do not

defeat the safety purpose of the grounding plug.

Disposal - Your Bosch product was developed and manufactured

with high-quality material and components that can be recycled

and reused. This symbol means that electronic and electrical

appliances, which have reached the end of their working life, must

be collected and disposed of separately from household waste

material. Separate collecting systems are usually in place for

disused electronic and electrical products. Please dispose of these

units at an environmentally compatible recycling facility, per

European Directive 2002/96/EC.

MIC Series Power Supplies Safety | en 9

Bosch Security Systems, Inc. Installation Manual F.01U.141.598 | 1.0 | 2009.11

Moving - Disconnect the power before moving the unit. Move

the unit with care. Excessive force or shock may damage the

unit and the hard disk drives.

Outdoor signals - The installation for outdoor signals, especially

regarding clearance from power and lightning conductors and

transient protection, must be in accordance with NEC725 and

NEC800 (CEC Rule 16-224 and CEC Section 60).

Permanently connected equipment - Incorporate a readily

accessible disconnect device in the building installation wiring.

Pluggable equipment - Install the socket outlet near the

equipment so it is easily accessible.

Power resupply - If the unit is forced to power down due to

exceeding the specified operating temperatures, disconnect

the power cord, wait for at least 30 seconds, and then

reconnect the power cord.

Power lines - Do not locate the camera near overhead power

lines, power circuits, or electrical lights, nor where it may

contact such power lines, circuits, or lights.

Rack-mount

– Ventilation - Do not place this unit in a built-in installation

or rack without proper ventilation or adhering to the

manufacturer's instructions. The equipment must not

exceed its maximum operating temperature requirements.

– Mechanical loading - Properly mount the equipment in a

rack to prevent a hazardous condition due to uneven

mechanical loading.

Video loss - Video loss is inherent to digital video recording;

therefore, Bosch Security Systems cannot be held liable for any

damage that results from missing video information. To

minimize the risk of lost digital information, Bosch Security

Systems recommends multiple, redundant recording systems,

and a procedure to back up all analog and digital information.

CAUTION!

Connecting System ground to Safety ground may result in

ground loops that can disrupt the CCTV system.

10 en | Safety MIC Series Power Supplies

F.01U.141.598 | 1.0 | 2009.11 Installation Manual Bosch Security Systems, Inc.

FCC & ICES Information

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following

measures:

– reorient or relocate the receiving antenna;

– increase the separation between the equipment and

receiver;

– connect the equipment into an outlet on a circuit different

from that to which the receiver is connected;

– consult the dealer or an experienced radio/TV technician

for help.

Intentional or unintentional modifications, not expressly

approved by the party responsible for compliance, shall not be

made. Any such modifications could void the user's authority to

operate the equipment. If necessary, the user should consult

the dealer or an experienced radio/television technician for

corrective action.

The user may find the following booklet, prepared by the

Federal Communications Commission, helpful: How to Identify

and Resolve Radio-TV Interference Problems. This booklet is

available from the U.S. Government Printing Office,

Washington, DC 20402, Stock No. 004-000-00345-4.

NOTICE!

This is a class B product. In a domestic environment this

product may cause radio interference, in which case the user

may be required to take adequate measures.

Otros manuales para MIC Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Fuente de alimentación de Bosch

Bosch

Bosch AL 36V-20 Manual de usuario

Bosch

Bosch Rexroth IndraControl VAU 01.1S Manual técnico

Bosch

Bosch LTC 5404/60 Manual de usuario

Bosch

Bosch rexroth IndraDrive HMV01 Series Manual de usuario

Bosch

Bosch PUC-EXACT 1 Manual de usuario

Bosch

Bosch MIC IP PSU Manual de usuario

Bosch

Bosch Rexroth IndraDrive HMV Manual técnico

Bosch

Bosch AL 1830 CV Manual de usuario

Bosch

Bosch AL 1810 CV Manual de usuario

Bosch

Bosch G3A-PSU1-4 Manual de usuario

Bosch

Bosch GAL18V-20 Manual de usuario

Bosch

Bosch MIC Series Manual de usuario

Bosch

Bosch Rexroth Diax 04 HVE Manual de usuario

Bosch

Bosch PSU-224-DC100 Manual de usuario

Bosch

Bosch Rexroth IndraDrive HMV02 Manual de usuario

Bosch

Bosch FPP-RNAC-8A-4C Guía de inicio rápido

Bosch

Bosch LTC 5414/60 Manual de usuario

Bosch

Bosch PMF 0004 A Manual de usuario

Bosch

Bosch rexroth IndraDrive HMV01 Series Manual de usuario

Bosch

Bosch Rexroth VM350 Manual de usuario

Bosch

Bosch PMF 0002 A Manual de usuario

Bosch

Bosch L 309 Series Manual

Bosch

Bosch AL 1830 CV Manual de usuario

Bosch

Bosch PSB 0004 A Manual de usuario

Manuales populares de Fuente de alimentación de otras marcas

Monacor

Monacor PS-12CCD Manual de usuario

VOLTIMA

VOLTIMA MagicBox 15 Manual de usuario

Agilent Technologies

Agilent Technologies 6032A Manual de usuario

Miller

Miller Auto Deltaweld 452 Manual de usuario

BCP

BCP PUOUBK Hoja de instrucciones

HC 2210 Manual de usuario

Puls

Puls CT5.241 Manual de usuario

OCZ

OCZ ZX1250W Manual de usuario

iseg

iseg ECH 238 Manual de usuario

Power

Power XXL A Series Manual de usuario

Agilent Technologies

Agilent Technologies 6631B Manual de usuario

Renogy

Renogy PHOENIX 300 Manual de usuario

HP 6200B Manual de servicio

Epson

Epson Stylus Scan 2500 Manual de funcionamiento

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manual de usuario

Puls

Puls MiniLine ML50.100 Manual de usuario

Puls

Puls AS-Interface SLA4.100 Manual de usuario

Kenwood

Kenwood PS-60 Manual de usuario