Bosch EDC17C46 Manual de usuario

info@chiptuningshop.co.uk

Manual for using EDC17C46 Bosch ECU probe with MPPS – Page 1

1 Description: This probe can be used for programming VAG EDC17C4 Bosch ECU`s. It fits in most BDM

positioning frames and is fitted with LED`s for accurate alignment on the ECU. The “Boot” resistors and the

ignition feed can be switched. With this adapter, there is no need to solder at all

Adapter Overview

A = Serial port connection B = Power Switch ON/OFF

C = Power Jack D = DIP Switches for BOOT Resistors ON/OFF

E = Ignition selection switch:

ON > The ignition pin of the ECU is supplied with a constant 12V power supply

In conjunction with boot resistors switched OFF, use this mode for reading of password on TP8-10+, a so can be

used for DS Check, and genera diagnostic requests etc..

K-Line > The ignition pin of the ECU is connected directly to the K-Line of the flash tool

The f ash too wi power the ignition pin and automatica y cyc e the power when required to reset the processor.

In conjunction with boot resistors switched ON, use this mode for reading/writing over boot oader.

OFF > The ignition pin of the ECU is supplied with nothing

F = Connect to flash tool. G = Connect to serial port on probe (A)

Manual for using EDC17C46 Bosch ECU probe with MPPS – Page 2

2 Handling and Adjustment: IMPORTANT - Make sure that the power switch (B) is in the “OFF” position

The power switch must remain OFF so that the pins are not live, until the probe is correctly aligned and in

contact with the corresponding pins on the ECU Failure to follow these instructions could result in damage

to the ECU!

Place the probe into the BDM frame retaining bracket and tighten the screws. Attach the adapter cable (G) to

the serial port (A) on the probe and plug the other end (F) into the OBD cable of your flash tool. Connect the

power supply to the probe jack (C), the LED's will now turn on to aid alignment, however the probe does not

power the ECU until the power switch (B) is turned on.

Adjust the ECU on the frame and move the retainer carefully towards the ECU. Ensure that all the pins are in

their designated position.

A diagram showing the location of the connections can be found on page 3.

It is very important, that the retainer is free from backlash and moves smoothly!

3 Reading password: (This step is only necessary for TP8+) Lift up the Boot DIP switches (D) as shown in

the adapter overview on page 1 and set the Ignition switch (E) to the “ON” position, you can now read the

password.

4 Programming the ECU: Push the DIP switches (D) down and set the “Ignition” switch (E) to the “K-Line”

position, then you can proceed with programming over boot mode.

5 Disconnecting: To safely disconnect the probe from the ECU, you must first remove TURN OFF THE

POWER Switch (B) Once the power supply is disconnected it is safe to lift the frame and probe away from

the ECU.

Manual for using EDC17C46 Bosch ECU probe with MPPS – Page 3

The pads marked in yellow have to make contact with the probe

Technical alterations reserved!

This product should be operated by competent personnel only. Chiptuningshop Ltd do not accept any responsibility

for damages, direct or consequential caused by improper handling.

Tabla de contenidos

Otros manuales de Adaptador de Bosch

Bosch

Bosch GHA FC2 Professional Manual de usuario

Bosch

Bosch GAA12V-21 Manual de usuario

Bosch

Bosch ADT-NONH-G3QM33 Manual de usuario

Bosch

Bosch Denoxtronic 2.2 Manual de usuario

Bosch

Bosch Professional GFA 12-H Manual de usuario

Bosch

Bosch 1 687 023 777 Manual de servicio

Bosch

Bosch 1687846016 Manual de usuario

Bosch

Bosch EasyControl Manual de usuario

Bosch

Bosch T40234 Manual de usuario

Bosch

Bosch Conettix D6680 Manual de usuario

Bosch

Bosch G 10 CL-1 Manual de usuario

Bosch

Bosch LTC 9213/01 Manual de usuario

Bosch

Bosch EasyControl Manual de usuario

Bosch

Bosch G 10 CL-1 Manual de usuario

Bosch

Bosch Rexroth Fe PROFIBUS-DP Bus Adapter Manual de usuario

Bosch

Bosch CDR 500 Kit Manual de usuario

Bosch

Bosch Conettix D6672 Manual de usuario

Bosch

Bosch Professional GAA 18V-48 Manual de usuario

Bosch

Bosch GAA12V-21 Manual de usuario

Bosch

Bosch GAA12V-21 Instrucciones de montaje

Bosch

Bosch Conettix ITS-D6682-INTL Manual de usuario

Bosch

Bosch EasyControl Instrucciones de funcionamiento

Bosch

Bosch Flasher LT Manual de usuario

Manuales populares de Adaptador de otras marcas

PCB Piezotronics

PCB Piezotronics 090B274 Manual de usuario

Auvidea

Auvidea J20 Manual del producto

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manual de usuario

Akribis

Akribis ITF-21-BISS-MIT Manual de usuario

Tenda

Tenda W54U Manual de usuario

ROHO

ROHO AGILITY Manual de usuario

PROLiNK

PROLiNK WN2001 Manual de usuario

Hawking

Hawking HUF2 Manual de usuario

Airlink101

Airlink101 AWLC4030 Manual de usuario

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manual de usuario

Philips

Philips SWA4554S/10 Manual de usuario

JVC

JVC TS-C9D2B Manual de instrucciones

NETGEAR

NETGEAR A6100 Manual de usuario

D-Link

D-Link DWA-121 Manual de usuario

Philips

Philips SWA2037 Manual de usuario

Basalte

Basalte 0610-20 Manual de usuario

Yealink

Yealink EHS40 Manual de usuario

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manual de usuario