BODYMAX RB60 Manual de usuario
USER MANUAL
BodyMax 60 recumbent bike
1
Safety Instructions
2
3
•
To ensure the best safety of the exerciser, regularly
check it on damages and worn parts.
• If you pass on this exerciser to another person or if
you allow another person to use it, make sure that
that person is familiar with the content and
instructions in these instructions.
• Only one person should use the exerciser at a time.
• Before the first use and regularly make sure that all
screws, bolts and other joints are properly tightened
and firmly seated.
• Before you start your work out, remove all sharp
edged objects around the exerciser.
• Only use the exercise for your work out if it works
flawlessly.
• Any broken, worn or defective part must
immediately be replaced and/or the exerciser must
no longer be used until it has been properly
maintained and repaired.
• Parents and other supervisory persons should be
aware of their responsibility, due to situations which
may arise for which the exerciser has not been
designed and which may occur due to children’s
natural play instinct and interest in experimenting.
• If you do allow children to use this exerciser, be
sure to take into consideration and assess their
mental and physical condition and development,
and above all their temperament. Children should
use the exerciser only under adult supervision and
be instructed on the correct and proper use of the
exerciser. The exerciser is not a toy.
• Make sure there is sufficient free space around the
exerciser when you set it up.
• To avoid possible accidents, do not allow children to
approach the exerciser without supervision, since
they may use it in a way for which it is not intended
due to their natural play instinct and interest in
experimenting.
• Please note that an improper and excessive work
out may be harmful to your health.
• Please note that levers and other adjustment
mechanisms are not projecting into the area of
movement during the work out.
• When setting up the exerciser, please make sure
that the exerciser is standing in a stable way and
that any possible unevenness of the floor is
evened out.
• Always wear appropriate clothing and shoes
which are suitable for your work out on the
exerciser. The clothes must be designed in a way
so that they will not get caught in any part of the
exerciser during the work out due to their form (for
example, length). Be sure to wear appropriate
shoes which are suitable for the work out, firmly
support the feet and which are provided with a
non slip sole.
• Be sure to consult a physician before you start
any exercise program. He may give you proper
hints and advice with respect to the individual
intensity of stress for you as well as to your work
out and sensible eating habits.
4
• Assemble the exerciser as per assembly instructions
and be sure to only use the structural parts
provided with the exerciser and designed for it.
Prior to the assembly, make sure the contents of
the delivery is complete by referring to the parts list
of the assembly and operating instructions.
• Be sure to set up the exerciser in a dry and even place and
always protect it from humidity. If you wish to protect the place
particularly against pressure points, contamination, etc.,
it is recommended to put a suitable, non slip mat under the exercise
• The general rule is that exercisers and training devices are no
toys. Therefore, they must only be used by properly informed
or instructed persons.
•Stop your work out immediately in case of dizziness,
nausea, chest pain or any other physical symptoms. In
case of doubt, consult your physician immediately.
•Children, disabled and hadicapped persons should
use the exercise only under supervision and in
presence of another person who may give support
and useful instructions.
•Be sure that your body parts and those of other
persons are never close to any moving parts of the
exerciser during its use.
•When adjusting the adjustable parts, make sure they
are adjusted properly and note the marked, maximum
adjusting position, for example of the saddle support,
respectively.
•Do not work out immediately after meals!
Exploded drawing
Part List
Part no. Description Drawing no. Material Specification Q'ty
1 Main frame 737RB 3 1000 J6 1
2 Front stabilizer 70501 6 2101 J0 Q195 D76x1.5Tx480L 1
3 Bottle holder 70402 6 2074 00 PVC 120*87*3T 1
4 Bolt 52605 5 0015 F0 10# M5*0.8*15L 2
5 Handlebar set 80201 3 2400 J5 1
6 Rear stabilizer 70501 6 2107 J1 Q195 D76x1.5Tx480L 1
7 Seat post 711RB 3 2200 J1 1
8 Computer 737RK 6 2501 B0 SM 1730 31 1
9L Left rolling foot cap 554C0 H 0076 B11 PP D76*120L 1
9R Right rolling foot cap 554C0 R 0076 B11 PP D76*120L 1
10 Handlebar post tube 737RB 3 2000 J0 1
11 Spring washer 55108 2 1520 FA 70# D15.4xD8.2x2T 14
12 domed nut 55208 6 2015 FA 35# M8x1.25x15L 6
13 Bolt 50308 5 0020 F0 35# M8x1.25x20L 8
14 Flywheel set 737RF 2 3100 00 1
15 Bolt 50308 5 0040 F3 35# M8*1.25*40 8
16 Screw cover 81502 6 2779 B0 PE D26*11L 2
17 Plastic washer 55110 1 2404 BF NL66 D10*D24*0.4T 2
18 Seat 80700 6 1146 B10 PVC 348*270*52 1
19 Bolt 50310 5 0035 C3 35# M10*35L 1
20L&R Pedal set 58029 6 1032 B0 JD 22A 9/16"tooth 1
21 Flat washer 55108 1 3020 NA Q235A D30*D8.5*2.0T 1
22 Screw 50904 2 0020 D0 10# ST4*1.4L*20L 2
23 Anti slip nut 18600 6 3175 N1 Q235A 3/8" 26UNFx6.5T 2
24 Fixed bracket for magnet 706E2 3 3200 N0 1
25 Backrest 80700 6 1145 B10 PVC 410*340*57 1
26 Tension cable 719M0 6 2602 02 D1.5*130L, 1
27 Spring 58003 6 1054 N0 72A D1.0*55L 1
28 Bolt 50106 5 0065 N0 35# M6*65L 1
29 Nut 55206 2 2006 NA Q235A M6*1*6T 1
30 Bolt 50308 5 0095 F4 35# M8*1.25*95L 4
31 Curved washer 55108 3 2215 FA Q235A D22xD8.5x1.5T 10
32 Power cord 702A2 6 2596 00 400L 1
33 Sensor cable 737RB 6 2576 00 400L 1
34 Waved washer 55117 5 2203 DA 65Mn D22*D17*0.3T 2
35 C ring 55517 1 0010 00 65Mn S 17(1T) 1
36 Belt 58004 6 1046 00 410 J5 (1041 J5) 1
37 Belt wheel 58008 6 1017 03 ZL102 D260*19 1
38 Round magnet 174R4 6 2574 00 M02 1
39L Left crank 58007 6 1045 02 1015A 6 1/2"x9/16" 20UNF 1
39R Right crank 58007 6 1046 02 1015A 6 1/2"x9/16" 20UNF 1
40 Ball knob 52916 2 0032 BB1 Q235A+ABS D50xM16x32xD8 1
41 Upper computer cable 807E2 6 2572 00 700L 1
42 Motor 73002 6 2571 00 1
43 Adjustable foot cap 55486 L 0076 B11 PP D76*86 2
44 Buffer 55308 4 0010 BB NBR+Q235A D20*10L*M8*1.25 1
45L Left chain cover 737RB 6 4501 B0 HIPS88 594*80.3*495 1
45R Right chain cover 737RB 6 4502 B0 HIPS88 594*76*495 1
46 Upper handle pulse cable 802S0 6 2585 00 600L 2
47
Middle handle pulse
cable 737RB 6 2587 00 2400L 2
48 Lower handle pulse cable 737RB 6 2586 00 100L 1
49 Handle pulse cable 802S0 6 2479 00 800L 1
50 Adaptor 804C2 6 2584 01 OUTPUT:9VA,500MA 1
51 Crank welding set 803MC 3 2903 00 1
52 Spacer bushing 58002 6 1081 01 D13.5*D10*9 1
53 Fixed plate for idle 24500 6 2674 N1 Q235A 156*62.2*5T 1
54 Idle 745S0 6 1671 00 D42*D38*24 1
55 Bolt 50308 5 0055 F3 35# M8*1.25*55L 2
56 Square neck bolt 50508 5 0055 F3 35# M8x1.25x55L 2
57 Plastic sleeve 803K0 6 1082 00 PVC D3*30L 2
58 Cap 553F0 1 0031 B3 PVC D25.4x31L 4
59L Rear chain cover(Left) 737RB 6 4512 BU0 HIPS88 321*44*242 1
59R Rear chain cover(Right) 737RB 6 4513 BU0 HIPS88 321*39.6*242 1
60 Sliding beam 711RB 3 5100 C2 1
61 Bolt 50108 2 0025 U0 35# M8x1.25x25 2
62 Front rear cover 73600 6 4514 B0 ABS 100*93*66 1
63 Anti loose nut 55206 1 2006 NA Q235A M6*1*6T 1
64 Nylon washer 55106 1 1915 B1 NL66 D6*D19*1.5T 1
65 Flat washer 55106 1 1310 NA Q235A D13*D6.5*1.0T 1
66 Flat washer 55108 1 1612 FA Q235A D16xD8.5x1.2T 18
67 Bolt 50106 5 0015 C0 35# M6x1.0x15L 4
68 Anti loose nut 55206 1 2006 CA Q235A M6x1.0x6T 4
69 Bearing 58006 6 1018 00 GCr15 #6003ZZ 2
70 Foam 58015 6 1287 B1 NBR D23*4T*415L 2
71 Foam 58015 6 1058 B0 NBR D23*4T*500L,with hole 2
72 Screw 50904 2 0010 D0 10# ST4x1.41x10.L 2
73 Square cap 55313 2 2525 B8 PE 25*25*13L 2
74 Handle pulse 16800 6 2478 00 PE18 2
75 Rear protective cover 73600 6 4515 B0 ABS 100*93*66 1
76 Flat washer 55117 1 2315 NA Q235A D23*D17.2*1.5T 1
77 Bolt 50108 5 0025 N3 35# M8*25 1
78 Spacer ring 80700 6 2781 00 Fe D22.5*D17.2*6.4T 1
79 Spring 58003 6 1024 N0 72A D2.2*D14*65L 1
80 Inner tube 73600 6 1071 B0 PE 40*80*102L 2
81 Anti loose nut 55210 1 2010 CA Q235A M10x1.5x10T 1
82 Bolt 52605 2 0012 N0 Q235A M5x0.8x12L 1
83 Bolt 50108 5 0052 N3 35# M8*52L 1
84 Anti loose nut 55208 1 2008 CA Q235A M8*1.25*8T 2
85 Nut 55208 2 2006 NA Q235A M8*1.25*6T 1
86 Seat supporting tube 809A2 3 1100 J1 1
87 Bolt 52605 5 0010 F0 10# M5*0.8*10L 4
88 Lower computer cable 703H2 6 2573 01 1200L 1
89 Screw 53342 2 0015 N0 10# ST4.2*1.4*15L 4
90 Screw 53342 2 0020 N0 10# ST4.2x1.4x20L 13
91 Pin 71600 6 4586 60 ABS D6*26.5*7.7 4
92 Buffer 708S0 6 1081 B0 NBR 20*90*1.7T 4
\ Allen wrench 58030 6 1031 N1 35# M6 1
\ Spanner 58030 6 1005 N2 Q235A 121*D6 1
CHECK LIST
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Bicicleta estática de BODYMAX
BODYMAX
BODYMAX CVET2706 Manual de usuario
BODYMAX
BODYMAX 40 Manual de usuario
BODYMAX
BODYMAX B2 Manual de usuario
BODYMAX
BODYMAX 80 Manual de usuario
BODYMAX
BODYMAX B15 Manual de usuario
BODYMAX
BODYMAX FXB10 Manual de usuario
BODYMAX
BODYMAX FXB30 Manual de usuario
BODYMAX
BODYMAX CVEB2419 Manual de usuario
BODYMAX
BODYMAX B50 Manual de usuario
BODYMAX
BODYMAX B200 Manual de usuario
