Boca Flasher HPNFC-HO Manual de usuario

Installation Manual

HPNFC-HO

WARNING: DO NOT LIFT FIXTURE BY CABLES.

This could result in permanent damage to both the xture and the cables. Damage resulting from grasping cables and/or putting

undue pressure on the cable connections will not be covered under the warranty! Do not attempt to install or use the HPNFC-HO

xture without reading the installation instructions and safety labels completely. Failure to adhere to these instructions could result in

serious injury or property damage. Do not modify, alter or attempt to service the HPNFC-HO. Doing so will void the warranty.

Installation Instructions

HPNFC-HO

Introduction:

The Boca HPNFC-HO is a line voltage xture that eliminates the need for secondary transformers, making installation contractor friendly.

The housing is a clear anodized aluminum with a durable nish making it weather and abrasion resistant. It is UL Listed for dry, damp or wet

location (model dependent). See layout drawings for model provided.

Maintenance:

CLEANING Dry and Damp (IP65) Rated Fixtures: To clean surface use a soft damp cloth.

Wet (IP68) Rated Fixtures: To clean surface use a soft cloth with mild soap and water.

STORAGE Store in a dry, well-ventilated area when product is not in

use. Keep the electrical cord away from heated surfaces

when in use or not in use. If cord shows signs of damage

do not use, return product to manufacturer.

Electrical Speciﬁcations:

1. Input Voltage: 90-120VAC, 230-277VAC

2. Total linear ft per 20A breaker: HO8 = 175’

Total linear ft per 20A breaker: HO6 = 200’

Total linear ft per 15A breaker: HO8 = 130’

Total linear ft per 15A breaker: HO6 = 150’

3. Input Current: HO8 = 114mA RMS per linear ft.

Input Current: HO6 = 95mA RMS per linear ft.

Indoor/Outdoor Shallow Prole Line Voltage

Model Dependent

Max temp: 55C

Min. temp: -40C

DAMP LISTING

IP65

WET LISTING

IP68

Turn Power Off At Circuit Breaker

Before Beginning Installation!

INCLUDED IN THIS PACKAGE:

Power cord length is

6.5ft per UL standard

Mounting Brackets

(2 brackets per xture)

Job Specic Drawings

123

HPNFC-HO

Swivel

Fixed

3" Arc

6" Arc

PAGE 2 OF 8

HPNFCHO Fixtures

(In lengths shown on job specic drawings)

Fixtures must be installed by a qualied and

licensed electrician in accordance with all national,

state and local electrical codes and regulations.

If any part of this manual does not meet the

necessary codes and regulations, contact the

factory for more information before attempting

to install.

Installation Instructions

HPNFC-HO

CAUTION: Before installing any type of clip (xed, swivel or arc) onto the mounting surface determine if the xtures have

rigid or twist lock connections at each end (examples of the rigid and twist lock types are shown in section 4).

FIGURE A: CLIP ALIGNMENT

PAGE 3 OF 8

Installation of clips for light ﬁxtures

with RIGID Connections

1. Light fixtures that have rigid connections on each end must be installed in the same plane and must also be in a straight alignment.

Using a chalk line or laser, mark a line on the flat surface where the clips are to be mounted. Align each clip to the chalk line using

the same reference point on each clip (clip edge or hole) and space the clips according to the length of each fixture (see figure A).

Clip placement: Boca Flasher recommends clips to be installed 1.5” from end cap. (see figure 3A)

2. Snap in the first light fixture into the clips (see section 2, installing fixtures into clips). Snap the 2nd. light fixture into adjacent clips

ensuring that the connections will mate (male to female).

3. Slide the second light fixture into the first light fixture until fully seated.

4.CAUTION DO NOT MATE FIXTURES THAT ARE NOT IN LINE OR FORCE

THIS CAN CAUSE PERMANENT DAMAGE TO FIXTURE CONNECTION AND OPERA

TOGETHER BY WIGGLING.

TION.

5.Continue this process until all light fixtures are installed according to the job specific layout drawings.

6.Connect fixtures to power per section 4 and 5.

Installation Instructions

HPNFC-HO

PAGE 4 OF 8

1. INSTALL CLIPS INTO SUBSTRATE

Place the notch on the clip

into the rst notch of the

xture.

Fixed Clips

Swivel Clips

3” Arc & 6” Arc Bracket Installation

Screw Information:

Screws not provided by Boca Flasher.

Boca Flasher recommends wide

washer pan head Phillips #8 screw

(not to exceed .418” in diameter).

3. Length of screw will vary depending

on mounting surface.

4. For outdoor installations, installer

should use a screw with

weatherproof coating.

2. INSTALL FIXTURE INTO CLIPS

Clip will securely

snap into place.

snap!

▶

Fixture will pivot on notch as

it is pushed down.

2b If using the Swivel Clip

or Arc Bracket loosen the

screw where the clip and

swivel bracket meet to ad-

just angle of the xture.

▶

Second Notch

▶

Detent

Angle

Screw

▶

Install security screw using

supplied screw and driver.

FIXTURE LENGTH FIXTURE LENGTH

Installation Instructions

HPNFC-HO

PAGE 5 OF 8

3. CLIP POSITIONING

FIXTURE LENGTH

Fixed Mounting Clip

Swivel Mounting Clip

FIXTURE LENGTH

Arc Mounting Clip

Changing fixture mount angle adjustable swivel clips only

1. Loosen screw shown on figure 1, on both ends of light

fixture.

2. Adjust light fixture to desired angle.

3. Tighten angle screw to lock into position.

Figure 1

▶

Adjustable Angle Screw

Note: If angle screw can not be reached using a straight

Phillips screwdriver an offset Phillips screwdriver may be

required.

Installation Instructions

HPNFC-HO

PAGE 6 OF 8

Installation of clips for light ﬁxtures

with TWIST LOCK Connections

1. Light fixtures that have twist lock connections on each end may be installed in areas where the surface plane may be at slightly different

levels between fixtures. Also, the light fixtures do not have to be in straight alignment and can be laid out to different angles and patterns.

2. Using a chalk line or laser mark a line on the flat surface where the 2 clips for the 1st. fixture are to be mounted. (See Figure: A)

3. Snap in the first light fixture into the clips (see section 2 installing fixtures into clips).

4. Using a chalk line or laser mark a line on the flat surface where the 2 clips for the 2nd fixture are to be mounted, this fixture can be placed on

a slightly different plane as long as the cord between the 2 fixtures is long enough. Also, this fixture can be placed at a different angle than

the first fixture (see figure 4).

5. Snap in the 2nd light fixture into the clips (see section 2 installing fixtures into clips).

6. Continue this process until all light fixtures are installed according to the job specific layout drawings.

7. Connect fixtures to power per section 4and 5.

Figure 4

See above for information

on determining layout.

Connect Male and Female

twist lock cables in

order shown on job

specic drawings.

Push together and then twist until

completely connected and sealed

if outdoors.

4.coNNect fIxtuRes toGetheR

twISt LOCK COnnECtIOn

Add tape to twist locks.

Place thumb over tape at starting point and

PULL around connector area until tape overlaps itself.

For weather-tight applications only

See additional instructions for weather-tight tape

Installation Instructions

HPNFC-HO

PAGE 7 OF 8

5.coNNect fIxtuRes to PoWeR

6.coNNect to A DIMMING systeM

7.ReMoVING fIxtuRes fRoM clIPs

IF NECESSARY

7aWhile holding the xture with your

other hand, pull back on screwdriver

to release from notch.

Slide a flat head screwdriver in 7b

between the clip and xture.

Once released from one notch,

xture can be fully removed.

*NOTE:

These xtures can dim on forward (leading)

or reverse (trailing) phase dimmers.

Boca Flasher does not recommend the use of

a “Smart” or phase-adaptive dimming module.

Installation Instructions

HPNFC-HO

IMPORTANT SAFETY REMINDERS:

We are constantly improving our fixtures and reserve the right to change options and specifications. Additional information & details at www.

bocaflasher.com. For specific requirements, contact your Boca Flasher sales representative. Boca Flasher, Inc. 552 NW 77th Street Boca Raton,

of their respective owners. REV 07-2017

DAMP LISTING

IP65

WET LISTING

IP68

1. DANGER:

To reduce the risk electric shock, always unplug the HPNFC-HO from electrical outlet before

cleaning. Cut breaker if outlet is not available.

2. To reduce the risk of burns, re, electric shock or injury to persons:

• UsetheHPNFC-HOonlyforitsintendeduseasdescribedintheseinstructions.

• DonotuseattachmentsnotrecommendedbyBocaFlasher.

• NeveroperatetheHPNFC-HOifithasadamagedcord,cableorplug,ifitisnotworking

properly, if it has been dropped or damaged, or dropped into water. If the seal appears to

be damaged/broken/torn return the xture to a service center for examination or repair.

• Keepcablesawayfromheatedsurfaces

• Neverdroporinsertanyobjectintoanyopening.

• Donotoperatewhereaerosol(spray)productsarebeingusedorwhereoxygen

is being administered.

3. WARNING:

Do not attempt to install or use the HPNFC-HO without reading the installation instructions

and safety labels. Failure to adhere to these instructions could result in serious injury

or property damage.

4. Do not modify, alter or attempt to service the HPNFC-HO:

Doing so will void the warranty.

5. There are no serviceable parts within the HPNFC-HO:

Please contact your local representative if issues arise on site during or after installation.

6. Do not use sharp tools near or on the xture lens:

Doing so will result in property damage and void the warranty.

Boca Flasher, Inc.

508 S. Military Trail nDeerfield Beach, Florida n33442 USA

Phone: 561-989-5338 nFax: 561-982-8323

www.bocaflasher.com

Tabla de contenidos

Otros manuales de Luz exterior de Boca Flasher

Boca Flasher

Boca Flasher SBL-MIX Manual de usuario

Boca Flasher

Boca Flasher LUMELINE Manual de usuario

Manuales populares de Luz exterior de otras marcas

Sealey

Sealey LED37 Manual de usuario

nordlux

nordlux VEJERS Guía del usuario

SImx

SImx ELITE LED LHTC637 Manual de usuario

GEV

GEV CAROLINE 10833 Manual de usuario

NEBO

NEBO NEB-LSP-0020 Manual de usuario

WE-EF

WE-EF PFL540 LED Manual de usuario

Lindby

Lindby 9949029 Manual de usuario

HEPER

HEPER DOGO Side LW6048.585-US Instrucciones de instalación y funcionamiento

HEPER

HEPER LW8034.003-US Instrucciones de instalación y funcionamiento

Maretti

Maretti VIBE S 14.6080.04.A Manual de usuario

BEGA

BEGA 84 253 Manual

HEPER

HEPER MINIMO Instrucciones de instalación y funcionamiento

LIGMAN

LIGMAN BAMBOO 3 Manual de usuario

Maretti

Maretti TUBE CUBE WALL 14.4998.04 Manual de usuario

Maxim Lighting

Maxim Lighting Carriage House VX 40428WGOB Manual de usuario

urban ambiance

urban ambiance UQL1273 Manual de usuario

TotalPond

TotalPond 52238 Manual de usuario

Donner & Blitzen

Donner & Blitzen 0-02661479-2 Manual de usuario