Blyss EL1716B Manual de usuario
GB
IE
Wall hung electric replace
Model EAN
EL1716B 1800W 3663602672777
EL1716W 1800W 3663602672999
Version : 04
2
This instruction manual is important to your safety.
Read the entire manual carefully before using the appliance and
keep it for future reference.
Getting started...
Safety 3-5
Before you start 6-7
Quick start 8-17
In more detail…
Trouble shooting 18
Maintenance and cleaning 18
Environmental protection 19
Technical specications 19-20
Installation 21-23
Let’s
get started...
2 3
PLEASE READ THE SAFETY ADVICE CAREFULLY
BEFORE USING THE APPLIANCE
Warning: risk of re, electric shock, physical injuries and
material damage.
Before using this appliance, always follow the safety
advice during assembly, use and maintenance.
SAFETY ADVICE (Use)
- This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way
and understand the hazards involved. Children shall not
play with the appliance. Cleaning and user maintenance
shall not be made by children without supervision.
- Children of less than 3 years should be kept away unless
continuously supervised.
- Children aged from 3 years and less than 8 years shall
only switch on/o the appliance provided that it has
been placed or installed in its intended normal operating
position and they have been given supervision or
instruction concerning use of the appliance in a safe way
and understand the hazards involved.
Children aged from 3 years and less than 8 years shall
not plug in, regulate and clean the appliance or perform
user maintenance.
-CAUTION : Somepartsofthisproduct can becomevery
hot and cause burns. Particular attention has to be given
where children and vulnerable people are present.
- WARNING : In order to avoid overheating, do not
cover the heater.
- If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly qualied
persons in order to avoid a hazard.
Safety
Let’s
get started...
4
PLEASE READ THE SAFETY ADVICE CAREFULLY
BEFORE USING THE APPLIANCE
- The appliance must not be used outdoors.
- The appliance is intended for domestic use only, and is not
suitable for household room illumination. Do not use this
appliance for anything other than its intended purpose.
- Do not operate the appliance in a room where ammable
liquids, solvents or varnishes are stored and/or where
ammable vapours may exist.
- The appliance must be placed at a minimum distance of
one metre from ammable materials and objects (curtains,
bedding, textiles, paper, etc.)
- Do not attempt to disassemble this appliance, repair it or
perform any modications yourself. This appliance does
not contain any parts that can be used separately.
- Keep plastic packaging out of the reach of children.
-Airinletandoutletventsmustnotbecoveredorobstructed
under any circumstances. Do not insert any objects into
these vents.
- Do not exert pressure on or hit the walls of the appliance.
- Do not set objects (wood logs, stones, pottery, etc.) on
the electric replace other than those designed for this
purpose.
Safety
4 5
PLEASE READ THE SAFETY ADVICE CAREFULLY
BEFORE USING THE APPLIANCE
SAFETY ADVICE (Installation)
- Information on appliance installation is provided in the
Installation section on pages 21 to 23.
- The heater must not be located immediately below a
socket-outlet.
- WARNING : Means for disconnection having a contact
separation in all poles must be incorporated in the xed
wiring in accordance with the wiring rules.
- CAUTION : In order to avoid a hazard due to inadvertent
resetting of the thermal cut-out, this appliance must not
be supplied through an external switching device, such as
a timer, or connected to a circuit that is regularly switched
on and o by the utility.
- WARNING : This appliance must only be used as a xed
appliance. It must be attached vertically and securely to a
vertical wall. Any other position is potentially dangerous.
- WARNING : This appliance is not protected against
splashes of water. It is not suitable for use in a bathroom.
- Do not use this heater in the immediate surroundings of a
bath, a shower or a swimming pool.
- CAUTION : to be installed by a professional in line with
the installation standards applicable in your country (NF
C15-100 for France or equivalent for other countries).
IMPORTANT : KEEP THIS INFORMATION FOR
FUTURE REFERENCE. READ CAREFULLY.
Safety Safety
6
Points to check before beginning
For domestic use only.
Children or any other persons incapable of using the appli-
ance safely must not use this appliance.
Please discard of plastic packaging appropriately and keep
it out of reach of children.
The appliance is conceived to be used as a supplementary
source of heat, not for the use as the main heating device.
Before you start
To install your product, please read the installation
guidelines at the end of the instruction manual.
You need (no included)
1 screwdriver
1 measuring tape
1 spirit level 1 drill and bit
6 7
1- Main body
2- Control panel
3- Remote control
x01 Wall support
x01 Wall bracket
x07 (ST4.2x40)
x07 (Ø6x35)
x02 (ST3.5x8))
The screws and wall plugs supplied are suitable for solid walls.
For all other types of wall, please use suitable screws and wall
plugs.
Points to check before beginning Your product
Before you start
3
1 2
8
The controls
Quick start
OK
MENU
A
MASTER POWER SWITCH (A)
- Open the cover and push button A down (I) to “ON” position or push but-
ton A down (O) to “OFF” position.
STANDBY ( )
- Press button to start or stop the ame eect.
Default interface displays as following :
- The heating icon will display and start heating
when the room temperature is less than the default
setting (10°C), on the contrary it will not display and
heat.
- The clock icon will be ashing because the
time is not set yet. Please follow the steps in “Time
Setting” to set the time.
.Two short beeps that increase in pitch sound when switched on and
three beeps that decrease in pitch sound when switched o.
.When switches on, the heating level, set temperature and clock icon
are displayed. The display will be disappeared after 60 second without
any operation. Press any button to display again.
LOCKING THE BUTTONS ()
- Press and hold button
for more than 6 sec-
onds to lock or unlock the buttons, “LOC” is
displayed and indicated that the buttons are
locked. Once it’s locked “LOC” will be ashing for 6
seconds then disappear, press any button “LOC”
will ash again.
- Long press button for 6 seconds to unlock the buttons.
.Please note the button is never locked.
8 9
Quick start
HEATING ON / OFF
HEATING MODE QUICK START
- Press button +or - to quick start heat setting (even though it’s under
weekly program) as following:
- Press either button +or -to see the current tem-
perature on screen.
- Press button +or - to adjust the temperature as
desired.
. If the set temperature is higher than the room temperature detected
by appliance, the heating starts. The heating will not start if the set
temperature is lower than the room temperature.
NOTE: The temperature range including OFF and from 10°C to 30°C.
OFF for no heating, 10°C to 30°C is the selectable temperatures.
LOW/HIGH HEATING & SETTING THE TEMPERATURE
HIGH HEATING
- At default interface, press button
≡
to display “H” and ashing
icon as following:
- Press
button to set temperature.
. The default temperature is 10°C (50°F).
- Press button +or - to adjust temperature.
. If the set temperature is higher than the room
temperature detected by appliance, the heating
starts. The heating will not start if the set tempera-
ture is lower than the room temperature.
10
Quick start
LOW HEATING
- At default interface, press button
≡
twice to display “L” and ashing
icon as following:
- Press button to set temperature.
- Press button +or - to adjust temperature.
. The default temperature is 10°C (50°F).
. If the set temperature is higher than the room
temperature detected by appliance, the heating
starts. The heating will not start if the set tempera-
ture is lower than the room temperature.
CELSIUS/FAHRENHEIT SETTING
The default temperature readout is Celsius.
- Long press button
≡
for 3 seconds.
- Press button +or - to change the temperature readout from Celsius “C“
to Fahrenheit “F“.
BRIGHTNESS CONTROL
- At default interface, press button
≡
to select the Brightness Control, it’s
displayed “bri” and ashing icon as following:
- Press button to start the brightness setting.
- Press button +or -to select the brightness level.
. 5 brightness levels are selectable.
. Default setting is 3.
5 is the highest level as shown following:
Quick start
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Idiomas:
Otros manuales de Chimenea de interior de Blyss
