Blue Technix Argos 3D-P33X Manual de usuario

Argos 3D -

P33X

Quick Start Guide

Version 1

BECOM BLUETECHNIX GmbH

Gutheil-Schoder-Gasse 17

1230 Wien

AUSTRIA

[email protected]om

www.bluetechnix.com

Argos3D-P33X –Quick Start Guide

Document No.: 900-308 / A

Publication date: June 22, 2017

Subject to change without notice. Errors excepted.

transmitted for any purpose in any form or by any means, electronically or mechanically, without expressly

written permission by BECOM BLUETECHNIX GmbH.

Windows is a registered trademark of Microsoft.

Table of Contents

1Unboxing .......................................................................................................................................... 5

1.1 In the box .................................................................................................................................. 5

1.2 Opening your Argos3D–P33X ................................................................................................... 5

1.3 Connecting your Argos3D–P33X .............................................................................................. 6

1.4 Connector Overview ................................................................................................................. 6

1.4.1 Connecting the power supply............................................................................................ 7

1.4.2 Connecting the Ethernet Cable ......................................................................................... 7

2Downloading the Evaluation Software ............................................................................................. 8

2.1 Support website ........................................................................................................................ 8

2.2 Start-up screen ......................................................................................................................... 9

2.3 Prepare your Network Interface Card (NIC) ............................................................................ 10

3Start using your Argos3D–P33X with ‘BltTofSuite’ ........................................................................ 11

4System Requirements & Support................................................................................................... 12

4.1 Support ................................................................................................................................... 12

5Document Revision History............................................................................................................ 13

The information herein is given to describe certain components and shall not be considered as a guarantee of

characteristics.

Terms of delivery and rights of technical change reserved.

We hereby disclaim any warranties, including but not limited to warranties of non-infringement, regarding

circuits, descriptions and charts stated herein.

BECOM BLUETECHNIX makes and you receive no warranties or conditions, express, implied, statutory or in

any communication with you. BECOM BLUETECHNIX specifically disclaims any implied warranty of

merchantability or fitness for a particular purpose.

BECOM BLUETECHNIX takes no liability for any damages and errors causing of the usage of this product. The

user of this product is responsible by himself for the functionality of his application. He is allowed to use the

product only if he has the qualification. More information is found in the General Terms and Conditions (AGB).

Information

For further information on technology, delivery terms and conditions and prices please contact BECOM

BLUETECHNIX (http://www.bluetechnix.com).

Warning

Due to technical requirements components may contain dangerous substances.

Quick Start Guide - Argos 3D - P33X Last change: 22 June 2017

Version 1

1Unboxing

1.1 In the box

Argos3D–P33X

CAT5/7 Ethernet Cable

Quick Start Guide

Power Supply *

* Note

The power supply’s operating temperature is specified from 0 to +40°C. This represents not

the effective working temperature of the Argos3D–P33X sensor!

1.2 Opening your Argos3D–P33X

To access the connector compartment unscrew the two screws on the Argos3D-P33X front and take

off the connector compartment lid.

Figure 1-1: Argos3D–P33X connector compartment screw positions

Quick Start Guide - Argos 3D - P33X Last change: 22 June 2017

Version 1

1.3 Connecting your Argos3D–P33X

1.4 Connector Overview

a. Power Connector

b. Ethernet

c. General purpose input 1 & 2

d. General purpose output 1 & 2

e. Modulation Light Interface

f. Trigger

g. RS232 / RS485

h. DIP-Switch

i. Reset-Button

j. Debug-UART

k. Status LED

Marks Pin #1

b a c f

ed g i

h j

Figure 1-2: Argos3D–P33X connectors and interfaces

Note

Please follow the next steps in the right order to get your ‘Argos3D-P33X’ up and running

correctly.

Quick Start Guide - Argos 3D - P33X Last change: 22 June 2017

Version 1

1.4.1 Connecting the power supply

To ensure, that your Argos3D–P33X works correctly, connect the ‘Argos3D’to a 12-30V DC power supply

using connector (a) and wait for approximately 20 seconds until the camera boots up.

Pin assignment on the power connector (a): Pin #1: +12V to +30V, Pin#2: GND

Note

The power supply connector is protected against wrong polarity but the ‘Argos3D’ will not

work in case you don’t use the correct polarity! If the Argos3D–P33X doesn’t work please

check the power supply polarity first!

1.4.2 Connecting the Ethernet Cable

Plug in the Ethernet cable (b) and connect your Argos3D–P33X to your PC.

Figure 1-3: Argos3D–P33X with connected power supply and Ethernet cable

Quick Start Guide - Argos 3D - P33X Last change: 22 June 2017

Version 1

2Downloading the Evaluation Software

Please log in to our support website at https://support.bluetechnix.com/ and download the Argos-P33X

customer software package. This package also includes the Bluetechnix ToF-Suite.

2.1 Support website

Select ‚free access‘

Figure 2-1: Download Evaluation Package

Quick Start Guide - Argos 3D - P33X Last change: 22 June 2017

Version 1

2.2 Start-up screen

Figure 2-2: Start-up screen

Please select your product: Argos3D –P33X

Please follow the instructions on the WEB-Site

Quick Start Guide - Argos 3D - P33X Last change: 22 June 2017

Version 1

2.3 Prepare your Network Interface Card (NIC)

Once you have connected your Argos3D–P33X to a Network Interface Card (NIC) of your PC give this NIC

the IP-Address 192.168.0.1 with a subnet mask of 255.255.255.0.

No driver must be installed on your PC!

The Argos3D–P33X uses IP-Address 192.168.0.10 with subnet mask 255.255.255.0.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios de Blue Technix

Blue Technix

Blue Technix Argos 3D-P320 Manual de usuario

Blue Technix

Blue Technix Argos 3D P310 Instrucciones de uso

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario