BLOTZ B28-DS Series Manual de usuario
28mm Dungeon System
B28-DS-xxx
Please read these instructions fully before starting construction.
PVA or equivalent glue will be required to stick sections together.
Sand paper can be used to gently clean any joints.
A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due care and remember
to cut away from yourself at all times.
During the construction of this model you may find it convenient to use pegs / elastic bands to hold pieces in place while
you allow glue to dry.
These are generic instructions as the components are very similar across the range so for example all doors go together
the same way regardless if they are single or double doors.
Walls / Corridors
Remove the inner wall section(s) which are the
walls with the lugs underneath them and the
“floor” from the sprue.
Put a dab of glue on the BACK of the lugs and push
them through the corresponding holes in the floor
so the etched details faces inwards (see pic)
Note at least one of the lugs will extend through
the floor by 2mm. This is intentional.
Apply glue to the centre of the under-floor and
attach it to the underside of the floor by aligning
the lugs.
Apply firm (but gentle) pressure to get the lugs to
slot into place.
Turn the piece over and attach the outer skin of
the wall making sure the ends align with the inner
skin. Any sprue points should be on the bottom of
the wall.
If you wish to glue any of the connectors
permanently into position then make sure you have
pull them as far to the right as they will go.
Archways
Remove the inner arch section which is the one
with the lugs underneath it and the “floor” from
the sprue.
Put a dab of glue on the BACK of the lugs and push
them through the corresponding holes in the floor
so the etched details faces inwards (see pic).
As with the “walls” you will find that some lugs
extend through the floor by 2mm. This is
intentional.
(picture is the underside of a wall section)
Apply glue to the centre of the under-floor and
attach it to the underside of the floor by aligning
the lugs.
Apply firm (but gentle) pressure to get the lugs to
slot into place.
Turn the piece over and attach the outer skin of
the archway making sure it aligns with the inner
skin.
If you wish to glue any of the connectors
permanently into position then make sure you have
pull them as far to the right as they will go.
Doors
Take each door and its handle from the sprue.
Apply glue to the handle and gently push it into
position so it extends out of both sides of the door.
Remove the inner doorway section which is the
one with the lugs underneath it and the “floor”
from the sprue. Glue them together per the walls
/ arches above.
Apply glue to the centre of the under-floor and
attach it to the underside of the floor by aligning
the lugs.
Apply firm (but gentle) pressure to get the lugs to
slot into place.
Glue the outer skin to the door (preferably not
with a fast-acting glue) and get the door and hinge
bar.
Put the bottom lug of the door into the hole in the
floor and the upper lug into the hinge bar.
Gently push one end of the hinge bar into the bar in
the doorframe.
Slide the outer skin of the door a little to the
left/right until the bar slides fully into position.
DO OT FORCE the bar or it may fracture at the
hinge end.
Glue the front and rear decorative pieces into
position. These help to hide the hinge bar and give
it additonal strength.
Corner Sections
These instructions are for all corner sections regardless if they have a door arch or plain wall.
For door sections please see the additional info (above) with regard to fitting the door into the space.
Take the two inner sections (those with lugs) and
attach them to the base with their etched detail
facing inwards (see pic).
Apply glue to the centre of the under-floor (after
checking its alignment) and attach it to the
underside of the floor by aligning the lugs.
Apply firm (but gentle) pressure to get the lugs to
slot into place.
Now add the
outer skin of the corner as per the
appropriate instructions above (i.e. wall arch or
door)
Otros manuales de Juguete de BLOTZ
BLOTZ
BLOTZ B20-ST-111 Instrucciones de uso
BLOTZ
BLOTZ B15-WW2-100 Manual de usuario
BLOTZ
BLOTZ B20-MD-019 Manual de usuario
BLOTZ
BLOTZ B28-ME-004 Manual de usuario
BLOTZ
BLOTZ WWII Sleeping Hut 20mm Manual de usuario
BLOTZ
BLOTZ B28-ME-008 Manual de usuario
BLOTZ
BLOTZ B20-ME-009 Manual de usuario
BLOTZ
BLOTZ Middle Eastern Building 9 Manual de usuario
BLOTZ
BLOTZ B15-MC-005 Manual de usuario
BLOTZ
BLOTZ 10mm Skyscraper Dice Tower Manual de usuario
BLOTZ
BLOTZ B28-SF-229 Manual de usuario
BLOTZ
BLOTZ B10-CS-103 Manual de usuario
BLOTZ
BLOTZ B00-RT-229 Manual de usuario
BLOTZ
BLOTZ 28mm Old West Store 2 B28-OW-109 Manual de usuario
BLOTZ
BLOTZ B15-MW-007 Manual de usuario
BLOTZ
BLOTZ B06-CS-003 Manual de usuario
BLOTZ
BLOTZ B20-ME-002 Manual de usuario
BLOTZ
BLOTZ B28-OW-108 Manual de usuario
BLOTZ
BLOTZ B00-ACC-400 Manual de usuario
BLOTZ
BLOTZ B06-MW-100 Manual de usuario
