Blizzard MYSTACL Z Manual de usuario

Blizzard Lighting, LLC

http://www.blizzardpro.com

Waukesha, WI USA

Page 2

TABLE OF CONTENTS

MystACL™ Z 1

1. Getting Started 3

What’s In The Box? 3

Getting It Out Of The Box 3

Powering Up! 3

Getting A Hold Of Us 3

Safety Instructions (Don’t Stick Your Hand In The Toaster!) 4

2. Meet The MystACL™ Z 5

Main Features 5

DMX Quick Reference 5

The MystACL™ Z Pin-up Picture 6

3. Setup 7

Fuse Replacement 7

Connecting A Bunch Of MystACL™ Z Fixtures 7

Data/DMX Cables 7

Cable Connectors 8

3-Pin??? 5-Pin??? Huh? 8

Take It To The Next Level: Setting up DMX Control 8

Fixture Linking (Master/Slave Mode) 9

Mounting/Rigging 9

Mounting Points 10

Clamp Mounting 11

4. Operating Adjustments 12

The Control Panel 12

Control Panel Menu Structure 13

DMX Mode 14

Select The DMX Starting Address 14

Run Mode (DMX/Artnet) 14

Master/Slave Mode 14

Select the Channel Mode 14

Auto & Sound Active Modes 14

Manual Adjustments 14

DMX Channel Values In-Depth 15

5. Appendix 18

Keeping Your MystACL™ Z As Good As New 18

Returns (Gasp!) 18

Shipping Issues 18

Tech Specs 19

Dimensional Drawings 19

Page 3

1. GETTING STARTED

What’s In The Box?

• 1 x MystACL™ Z

• An Ever-So-Handy Power Cord

•

A Set of Mounting Brackets

• DMX Cable

• This Lovely User Manual

Getting It Out Of The Box

Congratulations on purchasing the MystACL™ Z moving LED bar xture. Now that you’ve

got your MystACL™ Z (or hopefully Z's), you should carefully unpack the box and check the

contents to ensure that all parts are present and in good condition. If anything looks as if it

has been damaged in transit, notify the shipper immediately and keep the packing material

for inspection. Again, please save the carton and all packing materials. If a xture must

be returned to the factory, it is important that the xture be returned in the original factory

box and packing.

Powering Up!

All xtures must be powered directly o a switched circuit and cannot be run o a

rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer

channel is used solely for a 0% to 100% switch.

AC Voltage Switch - Not all xtures have a voltage select switch, so please verify that the

xture you receive is suitable for your local power supply. See the label on the xture or

refer to the xture’s specications chart for more information. A xture’s listed current

rating is its average current draw under normal conditions. Check the xture or device

carefully to make sure that if a voltage selection switch exists that it is set to the correct

line voltage you will use.

Warning! Verify that the voltage select switch on your unit matches the line

voltage applied. Damage to your xture may result if the line voltage applied does

not match the voltage indicated on the voltage selector switch. All xtures must

be connected to circuits with a suitable Ground (Earthing).

Getting A Hold Of Us

If something happens goes wrong, please visit www.blizzardpro.com/support and open a

support ticket. We’ll be happy to help, honest.

Disclaimer: The information and specications contained in this document are subject

to change without notice. Blizzard Lighting™ assumes no responsibility or liability for any

errors or omissions that may appear in this user manual. Blizzard Lighting™ reserves the

right to update the existing document or to create a new document to correct any errors

or omissions at any time. You can download the latest version of this document from www.

blizzardpro.com.

Author: Date: Last Edited: Date:

J. Thomas 9/21/2019 J. Thomas 9/21/2019

Page 4

Please read these instructions carefully. They include

important information about the installation, usage and

maintenance of this product.

SAFETY INSTRUCTIONS

• Please keep this User Guide for future use. If you sell the unit to someone

else, be sure that they also receive this User Guide.

• ALWAYS make sure that you are connecting to the proper voltage, and that

the line voltage you are connecting to is not higher than that stated on the de-

cal or rear panel of the xture.

• This product is intended for indoor use only.

• To prevent risk of re or shock, do not expose xture to rain or moisture.

• Make sure there are no ammable materials close to the unit while operating.

• The unit must be installed in a location with adequate ventilation, at least

20in (50cm) from adjacent surfaces. Be sure that no ventilation slots are

blocked.

• ALWAYS disconnect from the power source before servicing or replacing fuse

and be sure to replace with same fuse size and type.

• ALWAYS secure xture using a safety chain. NEVER carry the xture by its

head. Use its carrying handles.

• DO NOT operate at ambient temperatures higher than 104°F (40°C).

• In the event of a serious operating problem, stop using the unit immediately.

NEVER try to repair the unit by yourself. Repairs carried out by unskilled people

can lead to damage or malfunction. Please contact the nearest authorized tech-

nical assistance center. Always use the same type spare parts.

• NEVER connect the device to a dimmer pack.

• Make sure the power cord is never crimped or damaged.

• Never disconnect the power cord by pulling or tugging on the cord.

• Avoid direct eye exposure to the light source while it is on.

Caution! There are no user serviceable parts inside the unit. Do not

open the housing or attempt any repairs yourself. In the unlikely event

your unit may require service, please open a support ticket at www.

blizzardpro.com/support.

Page 5

2. MEET THE MYSTACL™ Z

MAIN FEATURES

• 10* 30W Osram Ostar RGBW 4-in-1 icker-free LEDs, 50,000 hours

• Fast and precise 3-60° zoomable beam angle

• 8-16 bit motorized 210 degree tilt

• Single or dual pixel mapping capabilities via DMX

• 3-layer eects via DMX with congurable pixel sets & macros

• Built-in macros with patterns + multiple color presets

• Smooth electronic dimming & 1-10Hz strobe eects

• Ecient low noise fan cooling system

• 3/5-pin DMX + RJ45 input/output connections

• PowerCON® TRUE1-compatible power input/output connections

• Dual omega brackets with 1/4-turn fasteners

CONTROL:

• Protocol: USITT DMX-512, Art-Net

• DMX channels: 13/26/28/46-channel modes

• Easy-to-use 5-button control panel with full color LCD display

• Operating modes: DMX512, master/slave, auto, sound active

DMX Quick Reference (13/26/28/46-Channel Modes)

13CH

Basic

26CH

Ext.

28CH

Normal

46CH

P-Map What It Does

1 1 1 1 Tilt

2 2 2 2 Tilt Fine

3 3 3 3 Zoom (wide <-> narrow)

4 -- 4 -- Set 1 - Color Macros (overrides set 1 R/G/B/W)

5 -- 5 -- Set 1 - Red

6 -- 6 -- Set 1 - Green

7 -- 7 -- Set 1 - Blue

8 -- 8 -- Set 1 - White

-- -- 9 -- Set 1 - Intensity

9 4 10 4 Strobe

10 -- 11 -- Master Dimmer

11 5 12 5 Reset (hold 255 for 5 seconds)

12 -- -- -- Pattern Macro Select

13 -- -- -- Pattern Macro Speed (fast <-> slow)

-- -- 13 -- Set 2 - Color Macros (overrides set 2 R/G/B/W)

-- -- 14 -- Set 2 - Red

-- -- 15 -- Set 2 - Green

-- -- 16 -- Set 2 - Blue

-- -- 17 -- Set 2 - White

-- -- 18 -- Set 2 - Intensity

-- -- 19 -- Set 3 - Color Macros (overrides set 3 R/G/B/W)

-- -- 20 -- Set 3 - Red

-- -- 21 -- Set 3 - Green

-- -- 22 -- Set 3 - Blue

-- -- 23 -- Set 3 - White

-- -- 24 -- Set 3 - Intensity

-- -- 25 -- Set 1 Pattern Length

-- -- 26 -- Pattern Macro Select

-- -- 27 -- Set 3 Pattern Length

-- -- 28 -- Pattern Macro Speed (fast <-> slow)

-- 6 -- 6 Master Dimmer

-- 7-10 -- -- Pixel Group 1+2 R/G/B/W Intensity

-- 11-14 -- -- Pixel Group 3+4 R/G/B/W Intensity

-- 15-18 -- -- Pixel Group 5+6 R/G/B/W Intensity

-- 19-22 -- -- Pixel Group 7+8 R/G/B/W Intensity

-- 23-26 -- -- Pixel Group 9+10 R/G/B/W Intensity

-- -- 7-46 Individual Pixels 1-10 R/G/B/W Intensity

Page 6

Figure 1: The MystACL™ Z Pin-Up Picture

Figure 2: The Front Panel

Power

Output

Power

Input

Fuse

Holder

Buttons

5-Pin DMX

In/Out

3-Pin DMX

In/Out

RJ45

In/Out

Power

Switch

LCD

Display

10* 30W

RGBW LEDs

with 3-60°

Zoom

Moving

Head with

210° Tilt

Full Color, 5-Button LCD

Control Panel

Page 7

3. SETUP

Fuse Replacement

Remove the fuse holder from of its housing. Then take out the dam-

aged fuse from its holder and replace with exact same type of fuse.

Reattach the fuse holder, and then reconnect power.

Connecting A Bunch of MystACL™ Z Fixtures

You will need a serial data link to run light shows using a DMX-512

controller or to run shows on two or more xtures set to sync in mas-

ter/slave operating mode. The combined number of channels required

by all the xtures on a serial data link determines the number of x-

tures the data link can support.

Fixtures on a serial data link must be daisy chained in one single line.

Also, connecting more than 32 xtures on one serial data link without

the use of a DMX optically-isolated splitter may result in deterioration

of the digital DMX signal. The maximum recommended cable-run dis-

tance is 500 meters (1640 ft). The maximum recommended number

of xtures on a serial data link is 32 xtures.

Data/DMX Cabling

To link xtures together you’ll need data cables. You should use data-

grade cables that can carry a high quality signal and are less prone to

electromagnetic interference.

For instance, Belden© 9841 meets the specications for EIA RS-485

applications. Standard microphone cables will “probably” be OK, but

note that they cannot transmit DMX data as reliably over long distanc-

es. In any event, the cable should have the following characteristics:

2-conductor twisted pair plus a shield

Maximum capacitance between conductors – 30 pF/ft.

Maximum capacitance between conductor & shield – 55 pF/ft.

Maximum resistance of 20 ohms / 1000 ft.

Nominal impedance 100 – 140 ohms

Before replacing the fuse, disconnect the power cord.

ALWAYS replace it with the same type and rating.

Page 8

Cable Connectors

Cables must have a male XLR connector on one end and a female XLR connec-

tor on the other end. (Duh!)

CAUTION: Do not allow contact between the common and the

xture’s chassis ground. Grounding the common can cause a ground

loop, and your xture may perform erratically. Test cables with an

ohm meter to verify correct polarity and to make sure the pins are not

grounded or shorted to the shield or each other.

3-Pin??? 5-Pin??? Huh?!?

If you use a controller with a 5-pin DMX output connector, it’s no problem! You can simply use the in-

stalled 5-pin DMX input and/or output connections found on the back of your xture(s).

Conductor 3-Pin Female (Output) 5-Pin Male (Input)

Ground/Shield Pin 1 Pin 1

Data 1- (Primary Data Link) Pin 2 Pin 2

Data 1+ (Primary Data Link) Pin 3 Pin 3

Data 2- (Optional Secondary Data Link) Pin 4 Pin 4

Data 2+ (Optional Secondary Data Link) Pin 5 Pin 5

Take It To The Next Level: Setting Up DMX Control

Step 1: Connect the male connector of the DMX cable to the female connector (output) on

the controller.

Step 2: Connect the female connector of the

DMX cable to the rst xture’s male connector

(input). Note: It doesn’t matter which

xture address is the rst one connected. We

recommend connecting the xtures in terms

of their proximity to the controller, rather than

connecting the lowest xture number rst, and

so on.

Step 3: Connect other xtures in the chain

from output to input as above. Place a DMX

terminator on the output of the nal xture to

ensure best communication.

Page 9

Fixture Linking (Master/Slave Mode)

1. Connect the (male) 3/5-pin connector side of the

DMX cable to the output (female) 3/5-pin connector

of the rst xture.

2. Connect the end of the cable coming from the

rst xture which will have a (female) 3/5-pin con-

nector to the input connector of the next xture

consisting of a (male) 3/5-pin connector. Then, pro-

ceed to connect from the output as stated above to

the input of the following xture and so on.

A quick note: Often,

the setup for Master-

Slave and Standalone

operation requires that

the rst xture in the

chain be initialized for

this purpose via either

settings in the control

panel or DIP-switches.

Secondarily, the xtures

that follow may also re-

quire a slave setting.

Check the “Operating Adjustments” section in this manual for com-

plete instructions for this type of setup and conguration.

Mounting & Rigging

This xture may be mounted in any SAFE position provided there is

enough room for ventilation.

It is important never to obstruct the fan or vents pathway. Mount the

xture using a suitable “C” or “O” type clamp. The clamp should be

rated to hold at least 10x the xture’s weight to ensure structural sta-

bility. Do not mount to surfaces with unknown strength, and ensure

properly “rated” rigging is used when mounting xtures overhead.

Adjust the angle of the xture by loosening both knobs and tilting the

xture. After nding the desired position, retighten both knobs.

• When selecting installation location, take into consideration lamp

replacement access (if applicable) and routine maintenance.

• Safety cables MUST ALWAYS be used.

• Never mount in places where the xture will be exposed to rain,

high humidity, extreme temperature changes or restricted ventilation.

Page 10

Mounting Points

Overhead mounting requires extensive experience, which includes

calculating working load limits, knowledge of the installation material

being used, and periodic safety inspection of all installation material

and the xture. If you lack these qualications, do not attempt the

installation yourself. Improper installation can result in bodily injury.

Caution!

Please be aware, you should have a qualied electrician performing all

of your electrical connection needs.

Be sure to complete all rigging and installation procedures before

connecting the main power cord to the appropriate wall outlet.

Tabla de contenidos

Otros manuales de Equipo de DJ de Blizzard

Blizzard

Blizzard POWER PLOW 810SS Suplemento

Blizzard

Blizzard Mister Stroboto Manual de usuario

Blizzard

Blizzard POWER PLOW 810SS Suplemento

Blizzard

Blizzard Lux Capacitor Manual de usuario

Blizzard

Blizzard Verismo Fresnel WW Manual de usuario

Blizzard

Blizzard AtmosFEAR Big Bad Lo Fo Manual de usuario

Blizzard

Blizzard ARIA Profile WW Manual de usuario

Blizzard

Blizzard POCKET PULSAR Manual de usuario

Blizzard

Blizzard HYPE 150 Manual de usuario

Blizzard

Blizzard Stiletto Ray-Z Manual de usuario

Blizzard

Blizzard Tournado WiMAX 7 Manual de usuario

Manuales populares de Equipo de DJ de otras marcas

ALPHA LITE

ALPHA LITE ALPHA 1500 Manual del propietario

Chauvet

Chauvet OVATION E-930VW Manual de usuario

Zumtobel

Zumtobel APHRODITE Home Manual de usuario

Snow Masters

Snow Masters Zig Oscillator Manual de usuario

EuroLite

EuroLite 50530554 Manual de usuario

Beamz

Beamz BUV243 Manual de usuario

thomann

thomann Stairville DJ Lase 40-G MK-III Manual de usuario

Eagletone

Eagletone 6 Eyes Flower Manual de usuario

EuroLite

EuroLite FLD-1508 Manual de usuario

Technical Pro

Technical Pro LG8xSEA Manual de usuario

JB Systems

JB Systems Lounge Laser DMX Manual de usuario

Lightmaxx

Lightmaxx Vega Halo 90 Manual de usuario

Elation

Elation FUZE WASH Z350 Manual de usuario

Maverick

Maverick MK3 WASH Manual de usuario

Infinity

Infinity TF-260C7 Fresnel Manual de usuario

Chauvet

Chauvet EVE E-50Z Manual de usuario

Eliminator Lighting

Eliminator Lighting E 138 Manual de usuario

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario