Blizzard Lighting KAYO.MORPH Manual de usuario
Blizzard Lighting, LLC
www.blizzardlighting.com
Waukesha, WI USA
Copyright (c) 2016
Page 2
Kryo.Morph™ User Manual - Rev. A (c) 2016 Blizzard Lighting, LLC
TABLE OF CONTENTS
Kryo.Morph™ Moving Head 1
1. Getting Started 3
What’s In The Box? 3
Getting It Out Of The Box 3
Powering Up! 3
Getting A Hold Of Us 3
Safety Instructions (Don’t Stick Your Hand In The Toaster!) 4
2. Meet The Kryo.Morph™ 5
Main Features 5
Additional Features 5
DMX Quick Reference 5
The Kryo.Morph™ Pin-up Picture 6
3. Setup 7
Fuse Replacement 7
Connecting A Bunch Of Kryo.Morph™s 7
Data/DMX Cables 7
Cable Connectors 8
3-Pin??? 5-Pin??? Huh? 8
Take It To The Next Level: Setting up DMX Control 8
Fixture Linking (Master/Slave Mode) 9
Mounting/Rigging 9
Mounting Points 10
Clamp Mounting 11
Changing The Lamp 12
Lamp Adjustment 13
4. Operating Adjustments 14
The Control Panel 14
Control Panel Menu Structure 15
DMX Channel Values In-Depth 17
Gobo Replacement 23
Troubleshooting 23
5. Appendix 24
A Quick DMX Lesson 24
Keeping Your Kryo.Morph™ As Good As New 25
Returns (Gasp!) 25
Shipping Issues 25
Tech Specs 26
Dimensional Drawings 27
Page 3
Kryo.Morph™ User Manual - Rev. A (c) 2016 Blizzard Lighting, LLC
1. GETTING STARTED
What’s In The Box?
• 1 x Kryo.Morph™ 10R Beam/Wash/Spot
• A sweet set of mounting brackets
• A groovy power cord
• This lovely user manual
Getting It Out Of The Box
Congratulations on purchasing the Kryo.Morph™, the most far-out moving head in the
galaxy with mind-blowing 3-in-1 beam/spot/wash capabilities! Now that you’ve got your
Kryo.Morph™ (or hopefully, Morphs!) you should carefully unpack the box and check the
contents to ensure that all parts are present and in good condition. If anything looks as if it
has been damaged in transit, notify the shipper immediately and keep the packing material
for inspection. Again, please save the carton and all packing materials. If a xture must
be returned to the factory, it is important that the xture be returned in the original factory
box and packing.
Powering Up!
All xtures must be powered directly off a switched circuit and cannot be run off a
rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer
channel is used solely for a 0% to 100% switch.
AC Voltage Switch - Not all xtures have a voltage select switch, so please verify that the
xture you receive is suitable for your local power supply. See the label on the xture or
refer to the xture’s specications chart for more information. A xture’s listed current
rating is its average current draw under normal conditions. Check the xture or device
carefully to make sure that if a voltage selection switch exists that it is set to the correct
line voltage you will use.
Warning! Verify that the voltage select switch on your unit matches the line
voltage applied. Damage to your xture may result if the line voltage applied does
not match the voltage indicated on the voltage selector switch. All xtures must
be connected to circuits with a suitable Ground (Earthing).
Getting A Hold Of Us
If something is wrong, please just visit our website at www.blizzardlighting.com/
support and open a support ticket. We’ll be happy to help, honest.
Blizzard Lighting
N24 W23750 Watertown Rd Suite B
Waukesha, WI 53188 USA
www.blizzardlighting.com
414-395-8365
Disclaimer: The information and specications contained in this document are subject
to change without notice. Blizzard Lighting™ assumes no responsibility or liability for any
errors or omissions that may appear in this user manual. Blizzard Lighting™ reserves the
right to update the existing document or to create a new document to correct any errors
or omissions at any time. You can download the latest version of this document from www.
blizzardlighting.com.
Author: Date: Last Edited: Date:
J. Thomas 1/31/2016 J. Thomas 2/8/2016
Page 4
Kryo.Morph™ User Manual - Rev. A (c) 2016 Blizzard Lighting, LLC
SAFETY INSTRUCTIONS
• This xture falls under protection class I, this xture must be earthed!
• This product is intended for indoor use only.
• Make sure that you are connecting to the proper voltage, and that the line voltage you are
connecting to is not higher than that stated on the decal or rear panel of the xture.
• Avoid direct eye exposure to the light source while it is on.
• To prevent risk of re or shock, do not expose xture to rain or moisture.
• The minimum distance between light output and the illuminated surface must be more
than 10 meters (32.8 FT).
• Do not touch the device’s housing bare hands during its operation (housing becomes hot).
Allow the xture to cool approximately 20 minutes.
• If the xture has been exposed to drastic temperature uctuation (e.g. after transporta-
tion), do not switch it on immediately. The arising condensation water might damage your
device. Leave the device switched off until it has reached room temperature.
• During the initial start-up some smoke or smell may arise. This is a normal process and
does not necessarily mean that the device is defective.
• The lamp has to be replaced when it is damaged or deformed due to the heat. Fast on-off-
cycles (e.g. 10 min. on/10 min. off) will reduce lamp life.
• Always disconnect the xture from AC power before cleaning, removing or installing the
fuses, or any part.
• For replacement use lamps and fuses of same type and rating only.
• Make sure there are no ammable materials close to the unit while operating.
• The unit must be installed in a location with adequate ventilation, at least 20in (50cm)
from adjacent surfaces. Be sure that no ventilation slots are blocked.
• ALWAYS secure xture using a safety chain. Use its carrying handles while transporting.
• DO NOT operate at ambient temperatures higher than 104°F (40°C).
• In the event of a serious operating problem, stop using the unit immediately. NEVER try
to repair the unit by yourself. Repairs carried out by unskilled people can lead to damage.
• NEVER connect the device to a dimmer pack.
• Make sure the power cord is never crimped or damaged.
Caution! There are no user serviceable parts inside the unit. Do not open the
housing or attempt any repairs yourself. In the unlikely event your unit may
require service, please contact us at www.blizzardlighting.com/support.
Page 5
Kryo.Morph™ User Manual - Rev. A (c) 2016 Blizzard Lighting, LLC
2. MEET THE KRYO.MORPH™ MOVING HEAD
MAIN FEATURES
• 280W Beam/Wash/Spot 3-in-1 Moving Head
• HRI 280W discharge lamp light source
• Smooth dimmer from 0 - 100%
• Control channels: 13/16/24-channel
• Pan: 540°/tilt: 270°, 8/16-bit
• Color wheel: 13 dichroic lters + white
• Rotating gobo wheel: 9 indexable and replaceable slot-n-lock glass gobos +open
• Static gobo wheel: 10 metal gobos & 4 beam reducers
• 8-facet circular bidirectional prism with speed control
• 6-facet linear bidirectional prism with speed control
• Frost effect: separate, variable
• Strobe effect with variable speed (up to 15 ashes/sec.)
• 8/16-bit motorized zoom and focus
• LCD touch screen + 4-button control menu
• Pan/tilt-lock mechanism
ADDITIONAL FEATURES
• Protocol: USITT DMX-512
• DMX Channels: 13/16/24-channel
• Operating modes: standalone, master/slave, auto, sound active
• Dual quarter-turn “OMEGA” clamp brackets
• PowerCon™ compatible in power connector
• Internal fan cooling system
DMX QUICK REFERENCE - 13/16/24-CHANNEL MODES
Channel Defe 13-channel Small 16-channel Standard 24-channel
1 Color Wheel Pan Pan
2 Shutter/Strobe Tilt Fine Pan
3 Dimmer Pan/Tilt Speed Tilt
4 Gobo 1 (Fixed) Macro Function Fine Tilt
5 Prism Color Wheel Pan/Tilt Speed
6 Prism Rotation Reserved Macro Function
7 Gobo 2 (Rotating) Gobo 1 (Fixed) Color Wheel
8 Frost Gobo 2 (Rotating) Reserved
9 Focus Gobo Rotation Reserved
10 Pan Prism Gobo 1 (Fixed)
11 Fine Pan Prism Rotation Gobo 2 (Rotating)
12 Tilt Frost Gobo Rotation
13 Fine Tilt Zoom Reserved
14 -- Focus Prism
15 -- Shutter/Strobe Prism Rotation
16 -- Dimmer Frost
17 -- -- Zoom
18 -- -- Fine Zoom
19 -- -- Focus
20 -- -- Fine Focus
21 -- -- Reserved
22 -- -- Shutter/Strobe
23 -- -- Dimmer
24 -- -- Reserved
Page 6
Kryo.Morph™ User Manual - Rev. A (c) 2016 Blizzard Lighting, LLC
Figure 1: The Kryo.Morph™ Pin-Up Picture
HRI 280W
Discharge
Lamp
Control
Buttons
Touchscreen LCD Display
Figure 2: The Rear Connections
Head/Arms
Carry
Handle
Power
Switch
Fuse Holder
5-Pin
DMX
Out
3-Pin
DMX
Out
5-Pin
DMX
In
3-Pin
DMX
In
Power
Input
Pan
Lock
Tilt
Lock
*The pan and tilt
lock latches should
be in their locked
positions during
transportation.
Move these
latches to their
unlocked positions
before operating
the xture.
Page 7
Kryo.Morph™ User Manual - Rev. A (c) 2016 Blizzard Lighting, LLC
3. SETUP
Fuse Replacement
With a phillips head screwdriver, unscrew the fuse holder out of its
housing. Remove the damaged fuse from its holder and replace with
exact same type of fuse. Reattach the fuse holder, and then reconnect
power.
Connecting A Bunch of Kryo.Morph™ Fixtures
You will need a serial data link to run light shows using a DMX-512
controller or to run shows on two or more xtures set to sync in mas-
ter/slave operating mode. The combined number of channels required
by all the xtures on a serial data link determines the number of x-
tures the data link can support.
Fixtures on a serial data link must be daisy chained in one single line.
Also, connecting more than 32 xtures on one serial data link without
the use of a DMX optically-isolated splitter may result in deterioration
of the digital DMX signal. The maximum recommended cable-run dis-
tance is 500 meters (1640 ft). The maximum recommended number of
xtures on a serial data link is 32 xtures.
Data/DMX Cabling
To link xtures together you’ll need data cables. You should use data-
grade cables that can carry a high quality signal and are less prone to
electromagnetic interference.
For instance, Belden© 9841 meets the specications for EIA RS-485
applications. Standard microphone cables will “probably” be OK, but
note that they cannot transmit DMX data as reliably over long distanc-
es. In any event, the cable should have the following characteristics:
2-conductor twisted pair plus a shield
Maximum capacitance between conductors – 30 pF/ft.
Maximum capacitance between conductor & shield – 55 pF/ft.
Maximum resistance of 20 ohms / 1000 ft.
Nominal impedance 100 – 140 ohms
Page 8
Kryo.Morph™ User Manual - Rev. A (c) 2016 Blizzard Lighting, LLC
Cable Connectors
Cables must have a male XLR connector on one end and a female XLR
connector on the other end. (Duh!)
CAUTION: Do not allow contact between the common and the x-
ture’s chassis ground. Grounding the common can cause a ground
loop, and your xture may perform erratically. Test cables with an
ohm meter to verify correct polarity and to make sure the pins are not
grounded or shorted to the shield or each other.
3-Pin??? 5-Pin??? Huh?!?
If you use a controller with a 5 pin DMX output connector, you will need to use a 5 pin to 3-pin adapter.
They are widely available over the internet and from specialty retailers If you’d like to build your own, the
chart below details a proper cable conversion:
Conductor 3-Pin Female
(Output)
5-Pin Male
(Input)
Ground/Shield Pin 1 Pin 1
DMX Data (-) Pin 2 Pin 2
DMX Data (+) Pin 3 Pin 3
Not Used. No Connection. No Connection.
Not Used. No Connection. No Connection.
Take It To The Next Level: Setting Up DMX Control
Step 1: Connect the male connector of the
DMX cable to the female connector (output)
on the controller.
Step 2: Connect the female connector of the
DMX cable to the rst xture’s male connec-
tor (input). Note: It doesn’t matter which
xture address is the rst one connected.
We recommend connecting the xtures in
terms of their proximity to the controller,
rather than connecting the lowest xture
number rst, and so on.
Step 3: Connect other xtures in the chain
from output to input as above. Place a DMX
terminator on the output of the nal xture
to ensure best communication.
Page 9
Kryo.Morph™ User Manual - Rev. A (c) 2016 Blizzard Lighting, LLC
Fixture Linking (Master/Slave Mode)
1. Connect the (male) 3/5-pin connector side of the
DMX cable to the output (female) 3/5-pin connector
of the rst xture.
2. Connect the end of the cable coming from the
rst xture which will have a (female) 3/5-pin con-
nector to the input connector of the next xture
consisting of a (male) 3/5-pin connector. Then, pro-
ceed to connect from the output as stated above to
the input of the following xture and so on.
A quick note: Often,
the setup for Master-
Slave and Standalone
operation requires that
the rst xture in the
chain be initialized for
this purpose via either
settings in the control
panel or DIP-switches.
Secondarily, the xtures
that follow may also re-
quire a slave setting.
Check the “Operating Adjustments” section in this manual for com-
plete instructions for this type of setup and conguration.
Mounting & Rigging
This xture may be mounted in any SAFE position provided there is
enough room for ventilation.
It is important never to obstruct the fan or vents pathway. Mount the
xture using a suitable “C” or “O” type clamp. The clamp should be
rated to hold at least 10x the xture’s weight to ensure structural sta-
bility. Do not mount to surfaces with unknown strength, and ensure
properly “rated” rigging is used when mounting xtures overhead.
Adjust the angle of the xture by loosening both knobs and tilting the
xture. After nding the desired position, retighten both knobs.
• When selecting installation location, take into consideration lamp
replacement access (if applicable) and routine maintenance.
• Safety cables MUST ALWAYS be used.
• Never mount in places where the xture will be exposed to rain,
high humidity, extreme temperature changes or restricted ventilation.
Page 10
Kryo.Morph™ User Manual - Rev. A (c) 2016 Blizzard Lighting, LLC
Mounting Points
Overhead mounting requires extensive experience, which includes
calculating working load limits, knowledge of the installation material
being used, and periodic safety inspection of all installation material
and the xture. If you lack these qualications, do not attempt the
installation yourself. Improper installation can result in bodily injury.
Caution!
Please be aware, you should have a qualied electrician performing all
of your electrical connection needs. Better safe than sorry!
Be sure to complete all rigging and installation procedures before
connecting the main power cord to the appropriate wall outlet.
Tabla de contenidos
Otros manuales de Equipo de iluminación de Blizzard Lighting
Blizzard Lighting
Blizzard Lighting Lo-Pro Flux Manual de usuario
Blizzard Lighting
Blizzard Lighting Flurry Spot Manual de usuario
Blizzard Lighting
Blizzard Lighting ToughPar V12 Manual de usuario
Blizzard Lighting
Blizzard Lighting Kontrol 5 Manual de usuario
Blizzard Lighting
Blizzard Lighting Torrent 90 Beam Manual de usuario
Blizzard Lighting
Blizzard Lighting MAX L Manual de usuario
Blizzard Lighting
Blizzard Lighting Mezmerizor 4FX Manual de usuario
Blizzard Lighting
Blizzard Lighting Switch Blade X3 Manual de usuario
Blizzard Lighting
Blizzard Lighting The Puck RGB Unplugged Manual de usuario
Blizzard Lighting
Blizzard Lighting COLORISE Exa Manual de usuario
Blizzard Lighting
Blizzard Lighting HUSH PAR Theatrik Manual de usuario
Blizzard Lighting
Blizzard Lighting Tournado SKY W-DMX Manual de usuario
Blizzard Lighting
Blizzard Lighting Puck CSI Xtreme Manual de usuario
Blizzard Lighting
Blizzard Lighting PixelStorm COB Mini Manual de usuario
Blizzard Lighting
Blizzard Lighting RokBox Manual de usuario
Blizzard Lighting
Blizzard Lighting SPOTMAN Manual de usuario
Blizzard Lighting
Blizzard Lighting Node:b RGBAL Manual de usuario
Blizzard Lighting
Blizzard Lighting ROCKER PANEL RGBAW Manual de usuario
Blizzard Lighting
Blizzard Lighting Puck Pro Zoom EXA Manual de usuario
Blizzard Lighting
Blizzard Lighting ICE 30 Manual de usuario
Manuales populares de Equipo de iluminación de otras marcas
Qazqa
Qazqa Suplux SL 3 Black 103062 Manual de usuario
Commercial Electric
Commercial Electric 54568141 Manual de usuario
CREE LIGHTING
CREE LIGHTING 304 Series Manual de usuario
Goobay
Goobay 49867 Manual de usuario
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manual de usuario
Alkalite
Alkalite Krypton KT-81 Manual de usuario
