Blizzard Lighting Puck Fab5 Skywire Manual de usuario

PUCK

THE

Blizzard Lighting, LLC

www.blizzardlighting.com

Waukesha, WI USA

Page 2

TABLE OF CONTENTS

The Puck™ Fab5 LED PAR Can 1

1. Getting Started 3

What’s In The Box? 3

Getting It Out Of The Box 3

Powering Up! 3

Getting A Hold Of Us 3

Safety Instructions (Don’t Stick Your Hand In The Toaster!) 4

2. Meet The Puck™ Fab5 LED PAR Can 5

Features 5

DMX Quick Reference (3/5/12-Channel Modes) 5

The Puck™Fab5 Pin-up Picture 7

3. Setup 8

Fuse Replacement 8

Connecting A Bunch Of Puck™ Fab5 LED PAR Cans 8

Data/DMX Cables 8

 UsingthisxturewiththewiCICLE®WirelessDMXSystem 8

4. Operating Adjustments 10

DMX Mode & DMX Mode Selection 10

Master/Slave Mode 10

Sound Active Mode 10

Custom Color Display 10

Fixture running hour display 11

Additional Operating Help 11

Troubleshooting 12

5. Appendix 13

A Quick DMX Lesson 13

Keeping The Puck™Fab5 LED PAR Can As Good As New 14

Returns (Gasp!) 14

Shipping Issues 14

Tech Specs 15

Page 3

1. GETTING STARTED

What’s In The Box?

 •1xPuck™Fab5FlatLEDPARFixture

 •1xIECPowerCord

 •ThisLovelyUserManual

Getting It Out Of The Box

Congratulations on being completely and utterly qtastic! Now that

you’ve got The Puck™ Fab5 (or hopefully, Pucks!), you should carefully

unpack the box and check the contents to ensure that all parts are

present and in good condition. If anything looks as if it has been dam-

aged in transit, notify the shipper immediately and keep the packing

material for inspection. Again, please save the carton and all packing

materials.Ifaxturemustbereturnedtothefactory,itisimportant

thatthexturebereturnedintheoriginalfactoryboxandpacking.

Powering Up!

Allxturesmustbepowereddirectlyoffaswitchedcircuitandcannot

be run off a rheostat (variable resistor) or dimmer circuit, even

if the rheostat or dimmer channel is used solely for a 0% to

100% switch.

AC Voltage Switch -Notallxtureshaveavoltageselectswitch,so

pleaseverifythatthextureyoureceiveissuitableforyourlocalpow-

ersupply.Seethelabelonthextureorrefertothexture’sspeci-

cationschartformoreinformation.Axture’slistedcurrentratingis

itsaveragecurrentdrawundernormalconditions.Checkthextureor

device carefully to make sure that if a voltage selection switch exists

that it is set to the correct line voltage you will use.

Warning! Verify that the voltage select switch on your unit

matches the line voltage applied. Damage to your xture may

result if the line voltage applied does not match the voltage

indicated on the voltage selector switch. All xtures must be

connected to circuits with a suitable Ground (Earthing).

Getting A Hold Of Us

If something is wrong, just give us a call or send an email.

We’ll be happy to help, honest.

Blizzard Lighting

W220 N1531 Jericho Ct. Suite E, Waukesha, WI 53186 USA

[email protected]

www.blizzardlighting.com

1.866.493.6025

Page 4

SAFETY INSTRUCTIONS

•PleasekeepthisUserGuideforfutureuse.Ifyouselltheunittosomeone

else, be sure that they also receive this User Guide.

•ALWAYSmakesurethatyouareconnectingtothepropervoltage,andthat

the line voltage you are connecting to is not higher than that stated on the de-

calorrearpanelofthexture.

•Thisproductisintendedforindooruseonly.

•Topreventriskofreorshock,donotexposexturetorainormoisture.

•Makesuretherearenoammablematerialsclosetotheunitwhileoperating.

•Theunitmustbeinstalledinalocationwithadequateventilation,atleast

20in (50cm) from adjacent surfaces. Be sure that no ventilation slots are

blocked.

•ALWAYSdisconnectfromthepowersourcebeforeservicingorreplacingfuse

and be sure to replace with same fuse size and type.

•ALWAYSsecurextureusingasafetychain.NEVERcarrythexturebyits

cord. Use its carrying handles.

•DONOToperateatambienttemperatureshigherthan104°F(40°C).

•Intheeventofaseriousoperatingproblem,stopusingtheunitimmediately.

NEVERtrytorepairtheunitbyyourself.Repairscarriedoutbyunskilledpeople

can lead to damage or malfunction. Please contact the nearest authorized tech-

nical assistance center. Always use the same type spare parts.

•NEVERconnectthedevicetoadimmerpack.

•Makesurethepowercordisnevercrimpedordamaged.

•Neverdisconnectthepowercordbypullingortuggingonthecord.

•Avoiddirecteyeexposuretothelightsourcewhileitison.

Caution! There are no user serviceable parts inside the unit. Do not

open the housing or attempt any repairs yourself. In the unlikely event

your unit may require service, please contact Blizzard Lighting at sup-

[email protected].

Page 5

DMX Quick Reference (12-Channel Mode)

Channel What It Does

1 Dimmer

2 Strobe (0-15 off, 16-255 strobe slow <-> fast)

3 Red Intensity

4 Green Intensity

5 Blue Intensity

6 Amber Intensity

7 White Intensity

8 Color Snap

9 Snap Speed (0-15 off, 16-255 Snap Slow <--> Fast)

10 Color Fade

11 Fade Speed (0-15 off, 16-255 Snap Slow <--> Fast)

12 Sound Active (0-127 off, 128-255 Sound Active)

2. MEET THE PUCK™ FAB5 FLAT LED PAR FIXTURE

MAIN FEATURES

• Light Source: 7* 15-wa, 5-in-1 RGBWA All-In-One LED’s

• Variable electronic strobe and dimmer

• Built-in automated programs via DMX and master/slave

• Built-in sound acve programs

• Full RGBAW color mixing in standalone and master/slave

• Color Preset (3-Channel), RGBAW (5-Channel) and extended (12-Channel) DMX

• Able to directly power the wiCICLE® wireless system via DMX

ADDITIONAL FEATURES

• Lightweight and Compact (It kept its New Years’ resoluon!)

• 4-Buon LED control panel for easy programming

• Dual bracket for exibility in mounng

• Power outlet for xture linking (up to 50 xtures)

• Running hours display

• Two-piece mounng yoke allows exibility in posioning

Opcal:

• Beam Angle: 25°, Field Angle: 29°

• Light Source: 7* 15-wa, 5-in-1 RGBWA All-In-One LED’s

• Flicker-free constant-current LED driver

Page 6

DMX Quick Reference (3-Channel Mode)

Channel What It Does

1 Dimmer (0-15 off, 16-255 Dim <--> Bright)

2 Strobe (0-15 off, 16-255 strobe slow <-> fast)

Color Select

Value Red Green Blue Amber White

001-004 ON

005-008 ON

009-012 ON

013-016 ON

017-020 ON

021-024 ON ON

025-028 ON ON

029-031 ON ON

032-035 ON ON

036-039 ON ON

040-043 ON ON

044-047 ON ON

048-051 ON ON

052-055 ON ON

056-059 ON ON

060-062 ON ON ON

063-066 ON ON ON

067-070 ON ON ON

071-074 ON ON ON

075-078 ON ON ON

079-082 ON ON ON

083-086 ON ON ON

087-090 ON ON ON

091-093 ON ON ON

094-097 ON ON ON

098-101 ON ON ON ON

102-105 ON ON ON ON

106-109 ON ON ON ON

110-113 ON ON ON ON

114-117 ON ON ON ON

118-120 ON ON ON ON ON

121-255 Chase (Slow <--> Fast)

DMX Quick Reference (5-Channel Mode)

Channel What It Does

1 Red Intensity

2 Green Intensity

3 Blue Intensity

4 Amber Intensity

5 White Intensity

Page 7

Figure 1: The Puck™ Fab5 Pin-Up Picture

Ridiculously

thin!

5-in-1 RGBWA-

Color LED’s

Figure 2: The Rear Connections

AC Power In/Out

DMX Out DMX In

LED Control Panel

Microphone

Dual

Mounting Yokes

Page 8

3. SETUP

Fuse Replacement

Withaatheadscrewdriver,wedgethefuseholderoutofits

housing. Remove the damaged fuse from its holder and replace

with exact same type fuse. Insert the fuse holder back in its

place and reconnect power.

Connecting A Bunch of Puck™ Fab5 Flat LED PAR Cans

You will need a serial data link to run light shows using a DMX-

512controllerortorunshowsontwoormorexturessetto

syncinmaster/slaveoperatingmode.Thecombinednumberofchannelsrequiredbyallthexturesona

serialdatalinkdeterminesthenumberofxturesthedatalinkcansupport.

Fixturesonaserialdatalinkmustbedaisychainedinonesingleline.Also,connectingmorethan32x-

tures on one serial data link without the use of a DMX optically-isolated splitter may result in deterioration

of the digital DMX signal.

The maximum recommended cable-run distance is 500 meters (1640 ft). The maximum recommended

numberofxturesonaserialdatalinkis32xtures.

Data/DMX Cabling

Tolinkxturestogetheryou’llneeddatacables.Youshouldusedata-gradecablesthatcancarryahigh

quality signal and are less prone to electromagnetic interference.

Forinstance,Belden©9841meetsthespecicationsforEIARS-485applications.Standardmicrophone

cables will “probably” be OK, but note that they cannot transmit DMX data as reliably over long distances.

In any event, the cable should have the following characteristics:

2-conductor twisted pair plus a shield

Maximum capacitance between conductors – 30 pF/ft.

Maximum capacitance between conductor & shield – 55 pF/ft.

Maximum resistance of 20 ohms / 1000 ft.

Nominal impedance 100 – 140 ohms

USING THIS FIXTURE WITH THE wiCICLE® WIRELESS DMX SYSTEM

Inadditiontotheunbridledthrillyoualreadyreceivedthersttimeyoupluggedin

yourxture,you’llbedelightedtoknowthatThisxturealsoworksseamlesslywithour

wiCICLE®WirelessDMXsystem,withoutadditionalpower.

•ONLYxturesbearingthislogoarecertiedforusewiththewiCICLE®withoutexternal

power.

•Unauthorizedmodicationand/orusingthewiCICLE®with

unapprovedxturesmaycausedamagetothewiCICLE®or

xture.UNDERNOCIRCUMSTANCESISBLIZZARDLIGHTING

RESPONSIBLE FOR ANY DAMAGE FROM SUCH OPERATION.

•FixturesbearingtheabovelogoMUSTonlyusecableandconnectorswhichseparate

chassis/case ground from cable shielding. Cabling with the shield connected to the connec-

tor’scase/chassismaycausemalfunctionanddamagetothewiCICLE®orxture.

•wiCICLE®transmittershaveadditionalpowerrequirementsandthereforecannotbe

powereddirectlyfromthexture.YouwillneedtoutilizethesuppliedAC/DCadaptorto

drivewiCICLE®transmittersinyoursystem.

Page 9

Each wiCICLE®acts as both a transmitter and a receiver, depending on whether a DMX

source is applied to the integral XLR connector. This is an extremely powerful feature of

the system, however, it also requires 1 piece of due dilligence, and that is the removal of

extraneous DMX signals from your lighting rig BEFORE proceeding.

SO: BEFORE DOING ANYTHING ELSE, YOU SHOULD DISABLE ANY BUILT-IN PRO-

GRAMS IN THE FIXTURES YOU WISH TO CONNECT AND/OR SET THEM AS SLAVES

PRIOR TO RETURNING THEM TO DMX MODE (IF APPLICABLE). Most xtures

contain a built-in automatic, sound active or custom program which is designed

to operate with the xture NOT connected to a DMX chain.

Someoftheseprogramswillautomaticallyrununlessthextureissettoslavemode.

ThesexturestypicallysenseDMXautomaticallyandswitchtoDMXmodeuponreceiving

DMX signal (our Pucks do that!)

If you plug a wiCICLE®“receiver”intoanautosensingxturesetasa“master,“chancesare

good that the wiCICLE®“receiver” will begin transmitting the master program. Most times,

this is undesirable, and taking the two seconds to switch these programs off will solve a lot

of ails.

Got that done? Good! Then let’s proceed!

1. Plug the wiCICLE®Receiverintothe“DMXIN”connectorofthextureandverifyitis

receiving power (the STATUS LED should illuminate.)

2. Connect the AC/DC adaptor to the the wiCICLE®Transmitter and verify it is receiving

power (the STATUS LED should illuminate.)

3. Press the RECESSED SELECTOR BUTTON on the Transmitter to select the operating

channel group. (The system will store this setting for future use)

The 7-Color Status LED will change color to indicate the current channel group:

4. Follow the same procedure on the Receiver to select the channel group.

5. Once both the transmitter and receiver(s) are both set to the same channel group,

connectthetransmittertotheDMXcontrollerortheDMXoutofaxtureonyourDMX

chain.

6. Once a DMX signal is provided to the transmitter, the status LED will blink RED slowly

until communication is established with the receiver. The status LED on the receiver(s)

willashGREEN slowly until communication is established.

7. Once the clearest channel is auto-selected, the status LEDs will blink quickly on both

the transmitter and receiver. NOTE: The color of the LED DURING operation does not

indicate channel group, instead it indicates whether the unit is transmitting or receiving.

That’s It!

WE HAD THIS SPACE, SO WE FIGURED WE’D DRAW

YOU A PICTURE:

Antenna Housing & 1/2-wave Antenna

Antenna ferrule & articulation joint

Stainless Steel Housing

Recessed Selector Button

3-Pin XLR Connector

(Male on transmitter, Female on receiver model)

· GROUP 1: RED

· GROUP 2: GREEN

· GROUP 3: YELLOW

· GROUP 4: BLUE

· GROUP 5: VIOLET

· GROUP 6: CYAN

· GROUP 7: WHITE

Status LED

NOTE: “GROUP”

number also

corresponds to the

“GROUP” setting on

our LightCaster™

wireless DMX

Transceiver.

Page 10

4. OPERATING ADJUSTMENTS

NOTE: After making any change, the unit will return to the correct mode in about 10 seconds.

DMX Mode

Allows the unit to be controlled by any universal DMX controller.

1.)ThedefaultmodeforthextureisDMX,whichappearsasAddr on the LED

Readout. Use the <ENTER> button then the <UP> and <DOWN> buttons to

choose a channel between 1and 512. Press <ENTER>againtoconrm.

2.) To change between 3 and 6 channel DMX mode, select ChNd, then press

<ENTER>. Select either 3Ch, 5Ch or 12Ch, then press <ENTER> again to

conrm.

Master/Slave Mode (Auto/Sound Active/Color Preset/Custom):

1.) Use standard DMX cables to daisy chain your units together via the DMX

connector on the rear of the units.

2.) Choose a unit to function as the Master. Select MAST. The master unit must be

therstunit.Finally,chaintheunitstogetherusingDMXcable.

Master SLNd then NASt toconrm.

3.) Select slave function by using the <UP>/<DOWN>keystoreachSLAVinthe

Master/Auto menu on the slave units, and they will react in the same as the Master.

Slave SLNd then SLAu toconrm.

NOTE: When a unit is set to slave and no master is connected, Stby will

appear on the LED display.

4.)Onthemasterxture,usethe<UP>/<DOWN> keys to reach SHND, which

allows you to select the following:

Sound active SoUn then <ENTER>toconrm.

Auto mode CoLo then Auto, then <ENTER>toconrm.

Color preset CoLo then CoL 1 - CoL 31, <ENTER>

Color strobe StCo then 0-255 (Slowest <-.-> Fastest)

then CoL 1 - CoL 31, <ENTER>

To set a custom color in Master/Slave/Standalone Mode:

Using this function, you can select any color by adjusting the Red, Green, Blue, Amber and

White values from 0-255. You may also adjust the color balance of the xture.

Please note that modifying the values in this step will affect ALL modes, therefore

we recommend resetting all levels to their highest value (255) after using this mode.

1.) Select NAnu from the control panel, then hit <ENTER>.

2.) Choose rEd, GrEE, bLuE, ANbE or Uhit, then hit <ENTER> to

conrm.

3.) Using the <UP>/<DOWN> keys, select the color you wish to display by

varying Red/Green/Blue intensity between 0 and 255, then hit <ENTER>toconrm

each color choice.

4.) Select Color preset mode as instructed above, then select CoL 15. then

<ENTER>toconrm.

Otros manuales para Puck Fab5 Skywire

Tabla de contenidos

Otros manuales de Foco de Blizzard Lighting

Blizzard Lighting

Blizzard Lighting pixelstorm 240 Manual de usuario

Blizzard Lighting

Blizzard Lighting Stiletto 6 Manual de usuario

Blizzard Lighting

Blizzard Lighting EM-Pulse Manual de usuario

Blizzard Lighting

Blizzard Lighting Rokbox 5 RGBAW Manual de usuario

Blizzard Lighting

Blizzard Lighting ProPar Seven 3 Manual de usuario

Blizzard Lighting

Blizzard Lighting SnowBank Manual de usuario

Blizzard Lighting

Blizzard Lighting Highbeam Manual de usuario

Blizzard Lighting

Blizzard Lighting COBZilla RGB Manual de usuario

Blizzard Lighting

Blizzard Lighting puck Q12 Manual de usuario

Blizzard Lighting

Blizzard Lighting Puck Fab5 Skywire Manual de usuario

Blizzard Lighting

Blizzard Lighting ToughSTICK RGBAW Manual de usuario

Blizzard Lighting

Blizzard Lighting Stiletto Z 19 Manual de usuario

Blizzard Lighting

Blizzard Lighting SkyBox 5 Manual de usuario

Blizzard Lighting

Blizzard Lighting Snowblind FX Manual de usuario

Blizzard Lighting

Blizzard Lighting Flurry Wash Manual de usuario

Blizzard Lighting

Blizzard Lighting Weather System cob Manual de usuario

Blizzard Lighting

Blizzard Lighting Puck Q6 Unplugged Manual de usuario

Blizzard Lighting

Blizzard Lighting Torrent F5 Manual de usuario

Manuales populares de Foco de otras marcas

VIZULO

VIZULO Micro Martin Guía del usuario

EuroLite

EuroLite LED IP FL-100 SMD Manual de usuario

Cooper Wheelock

Cooper Wheelock XB12 Manual de usuario

Allen + Roth

Allen + Roth 17624-000 Manual de usuario

ADJ

ADJ 4 STAGE PAK Manual de usuario

Cooper Lighting

Cooper Lighting EGL91SW233 Manual de usuario

Max

Max 37496 Manual de usuario

BEGA

BEGA 85 143 Manual de usuario

Beamz

Beamz 151.226 Manual de usuario

EuroLite

EuroLite LED IP FL-8 Manual de usuario

Ledj

Ledj PERFORMER 36 RGB Manual de usuario

Perel

Perel ELS3 Manual de usuario

Perel

Perel ELS3WD Manual de usuario

LumX

LumX LM 36130 Manual de usuario

Xtricity

Xtricity 4-80053 Manual de usuario

Stahl

Stahl 6521/4 Series Manual de usuario

Ecosense

Ecosense EcoSpec Manual de usuario

Ayrton

Ayrton minipanel FX Manual de usuario