BLIP BLN2i-WF Manual de usuario

08-01-2017

Installation manual

BlipTrack BNL2i-WF v1.1

BLIP Systems A/S · support@blipsystems.com · +45 98847202 · www.blipsystems.com

ENGLISH - INDOOR SENSOR

INSTALLATION MANUAL – BLN2i-WF

Page 2 of 11

BLIP Systems A/S · [email protected] · +45 98847202 · www.blipsystems.com

08-01-2017

Installation manual

BlipTrack BNL2i-WF v1.1

INSTALLATION MANUAL – BNL2i-WF

- TABLE OF CONTENTS

Storage of BlipTrack BNL2iWF:

There are no special storage concerns to be observed for this unit

This and other handling manuals (preparation, installation, troubleshooting, storage,

maintenance and other general information) can be found on BLIP Systems web-page:

http://www.blipsystems.com/download/

Contents

Step 1 - Preparations 3

Step 2 - Remove side panels and top lid for mounting access 4

Step 3 - Create cable access 5

Step 4 - Mount the unit safely at the measuring point 6

Step 5 - Connect the unit to the PoE LAN network 7

Step 6 - Check the power-on sequence 8

Step 7 - Fasten the lid and side panels of the unit 9

Step 8 - Await unit conguration 10

Step 9 - Complete the installation 11

Page 3 of 11

BLIP Systems A/S · [email protected] · +45 98847202 · www.blipsystems.com

08-01-2017

Installation manual

BlipTrack BNL2i-WF v1.1

INSTALLATION MANUAL – BNL2i-WF

STEP 1 - PREPARATIONS

1. Check by visual inspection that the unit is undamaged.

2. The serial number and the MAC address are found from the label on the back of the

unit.

3. Check the unit has the correct serial number as agreed with BLIP Systems.

4. Record the MAC address of the unit for the conguration stage.

5. The unit has been fully tested at BLIP Systems prior to shipment so the unit can

be installed “out-of-the-box” at the measurement point without any further

preparations.

6. A LAN cable with PoE (Power over Ethernet) shall be available at the measurement

point.

Back

MAC Address Serial number

Page 4 of 11

BLIP Systems A/S · [email protected] · +45 98847202 · www.blipsystems.com

08-01-2017

Installation manual

BlipTrack BNL2i-WF v1.1

INSTALLATION MANUAL – BNL2i-WF

STEP 2

- REMOVE SIDE PANELS AND TOP LID FOR MOUNTING ACCESS

• The two side panels are released by pressing the small wings and lifting the

side panels upwards.

• Remove the lid by unscrewing the four screws. (Lift the lid carefully to avoid

damaging the green antennas)

Small wing

Four screws

Page 5 of 11

BLIP Systems A/S · [email protected] · +45 98847202 · www.blipsystems.com

08-01-2017

Installation manual

BlipTrack BNL2i-WF v1.1

INSTALLATION MANUAL – BNL2i-WF

STEP 3 - CREATE CABLE ACCESS

To ease creating the cable access the L2i module may be removed.

1. Remove the USB cable from the L2i-module.

2. Remove the L2i module from the unit by lifting it upwards.

3. Cut the rubber cable entry open for normal LAN cable access/Or drill a hole in

the cabinet if the LAN cable shall enter the unit through the back pane.

4. Mount the L2i module again by pressing it rmly onto the four taps.

5. Reattach the USB cable.

USB Cable

Tabs for the L2i module

Entry for LAN Cable

Page 6 of 11

BLIP Systems A/S · [email protected] · +45 98847202 · www.blipsystems.com

08-01-2017

Installation manual

BlipTrack BNL2i-WF v1.1

INSTALLATION MANUAL – BNL2i-WF

STEP 4 - MOUNT THE UNIT SAFELY AT THE MEASURING POINT

• It is recommended to use the prepared mounting locations within the

cabinet when mounting the unit.

• If the PoE LAN cable shall enter the unit through the cabinet then feed the

cable through before mounting the unit.

• The unit is normally placed in the ceiling having unobstructed view in all

directions.

• If mounted on a wall the cable entry shall face downwards for moisture

protection.

• The unit shall be placed 3-10 meters above ground level.

• When mounting the unit it must be placed at least 1 meter apart from any

other radio based equipment.

Location for drilling mounting holes

Page 7 of 11

BLIP Systems A/S · [email protected] · +45 98847202 · www.blipsystems.com

08-01-2017

Installation manual

BlipTrack BNL2i-WF v1.1

INSTALLATION MANUAL – BNL2i-WF

STEP 5 - CONNECT THE UNIT TO THE POE LAN NETWORK

1. If the PoE LAN cable shall enter through the cable entry of the cabinet then feed it

through now.

2. Attach the cable in the LAN slot of the L2i module.

3. As soon as the active PoE LAN cable is attached the unit will be powered and begin

to operate

LAN Cable Plug

Page 8 of 11

BLIP Systems A/S · [email protected] · +45 98847202 · www.blipsystems.com

08-01-2017

Installation manual

BlipTrack BNL2i-WF v1.1

INSTALLATION MANUAL – BNL2i-WF

STEP 6 - CHECK THE POWER-ON SEQUENCE

The unit is powered on when attaching the PoE LAN cable (The outer green LED will go on).

All four Status LED’s will ash once after approx. 20 sec as part of the basic wake up.

• Then both green Status LED’s will start blinking.

The correct operational status is:

• The inner green LED = On (Connected to BlipServer).

• The outer green LED = Blinking (Power & OS is OK).

• Blue LED = Irrelevant for the Indoor Sensor (No Bluetooth activity).

• Yellow LED = Irrelevant for the Indoor Sensor (No modem).

The unit will try to connect to the BlipServer after the basic wake-up.

The unit is shipped without any BlipServer conguration which is needed for successful

operation. So at this point check that the outer green LED is on when attaching the PoE

LAN cable and that both LED’s will start blinking after the wake up ash.

Page 9 of 11

BLIP Systems A/S · [email protected] · +45 98847202 · www.blipsystems.com

08-01-2017

Installation manual

BlipTrack BNL2i-WF v1.1

INSTALLATION MANUAL – BNL2i-WF

STEP 7 - FASTEN THE LID AND SIDE PANELS OF THE UNIT

1. Fasten the lid rmly using the four screws.

2. Click the two side panels in place to close the unit. (Be mindful of the green

antennas)

Four screws

Page 10 of 11

BLIP Systems A/S · [email protected] · +45 98847202 · www.blipsystems.com

08-01-2017

Installation manual

BlipTrack BNL2i-WF v1.1

INSTALLATION MANUAL – BNL2i-WF

STEP 8 - AWAIT UNIT CONFIGURATION

Check that the MAC address of the unit (recorded in “Preparations”stage) can be seen

from the local LAN server.

Blip Support can now provide the needed BlipServer conguration remotely.

1. Contact BLIP Support when the unit is ready for conguration providing the serial

number.

Blip Support can be reached from [email protected]om or phone +4598847202.

Blip Support will report back when the conguration has been completed.

The unit is now linked to the BlipServer and ready for operation.

MAC Address

Tabla de contenidos

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario